LEMOKEY G1 (01) PDF DOCUMENT

The LEMOKEY G1 mouse consists of the following parts:

1. Left button

2. Right button

3. Middle wheel button

4. Forward button

5. Backward button

6. Mouse indicator

7. DPI button

8. Modes toggle (B/OFF/G)

9. 2.4GHz Type-A receiver

10. Receiver compartment

To use the LEMOKEY G1 in wired mode, follow these steps:

1. When the mode switch is in the “OFF” position, the mouse will not respond if the cable is not connected.

2. Connect the included cable to the TYPE-C port on the mouse and the other end to a USB port on your device. The mouse is ready to use once the indicator lights up.

Please note: When the LEMOKEY G1 is connected by cable, it will default to wired mode, even if the toggle switch is in Bluetooth or 2.4GHz mode.

1. Switch the modes toggle on the bottom of the mouse to “G” (2.4GHz mode). The mouse will automatically enter 2.4GHz pairing mode, and the mouse indicator will slowly flash green.

2. Find the 2.4GHz receiver and connect it to your device’s USB port. Once successfully connected, the mouse indicator will turn solid green for 3 seconds before dimming. The mouse is now ready for use.

In 2.4GHz pairing mode, the mouse indicator will slowly blink green for 3 minutes. If the mouse does not connect within this time, the indicator will turn off.

To reconnect or re-enter pairing mode:

Hold the “Left button + Middle Wheel + Right button” simultaneously for 4 seconds to re-enter pairing mode.

To repair the connection:

1. Unplug the 2.4GHz receiver from your device.

2. Hold the “Left button + Middle Wheel + Right button” simultaneously for 4 seconds until the green light indicator starts flashing.

3. Plug the 2.4GHz receiver back into your device to complete the pairing process.

Note: It is recommended that when pairing the G1 in 2.4GHz mode, the mouse should be within 20cm of the receiver.

For the best wireless experience with your LEMOKEY G1, we recommend using the included cable and adapter to place the 2.4GHz receiver somewhere on your desk close to your mouse. This helps achieve a lower rate of latency and reduces potential signal interferences.

1. Switch the modes toggle on the bottom of the mouse to “B” (Bluetooth). The mouse will automatically enter Bluetooth pairing mode, and the indicator will slowly flash blue.

2. Open the Bluetooth settings on your device, search for a device named “Lemokey G1”, and then click “connect” to complete the pairing.

If the mouse is not connected within 3 minutes, the indicator will turn off. To reconnect, hold the “Left button + Middle Wheel + Right button” for 4 seconds to re-enter pairing mode.

If the LEMOKEY G1 is already in Bluetooth mode and you need to pair it with a new device, hold both the “Left button + Middle Wheel + Right button” for 4 seconds. Wait for the blue light to flash, which indicates the mouse has re-entered pairing mode. You can now connect the new device to the G1.

You can cycle through the DPI settings by pressing the DPI button on the bottom of the LEMOKEY G1 mouse. The mouse indicator light will change color to show the current DPI level.

The report rate can be adjusted in the driver software. The indicator light on the mouse corresponds to the selected report rate as follows:

Auto-Sleep mode helps conserve battery life. It is not activated when the LEMOKEY G1 is in wired mode. In Bluetooth or 2.4GHz mode, the mouse will go into Auto-Sleep mode after 10 minutes of sitting idle. To wake the mouse, simply move or click it.

To factory reset your LEMOKEY G1, hold down both the “DPI” button and the “Middle Wheel” button simultaneously for 4 seconds. All the LED lights on the mouse will blink three times to indicate that the factory reset was successful.

The charging indicator lights on the LEMOKEY G1 have the following meanings:

Fully Charged: The mouse indicator will stay GREEN.

Low Power: The mouse indicator will slowly blink RED.

When connected via USB Type-C for charging but not paired with a device:

• The mouse indicator will stay RED when charging.

• The mouse indicator will stay GREEN when fully charged.

For the best signal and charging speed, connecting to a USB3.0 port is recommended.

Note: The product supports up to 5V charging voltage and 300 mA charging current. Problems caused by improper recharging are not covered.

The box contains the following items:

• Mouse x 1

• Type-C cable x 1

• Extension adapter x 1

• Type-A receiver x 1

• User manual x 1

• Type-A to Type-C adapter x 1

Size: 116.8*59.5*39.4mm

Weight: 55 ± 3g

Sensor: PixArt 3950

Resolution: 100 – 30000 DPI

Mouse micro switches: Huano Micro Switch (80 million clicks life time)

Connection range: Approx 10m in open space (2.4GHz / Bluetooth)

Battery capacity: 600mAh

Usage duration:

• 140 Hours (Bluetooth mode)

• 120 Hours (1000Hz)

• 45 Hours (4000Hz)

• 40 Hours (8000Hz)

Recharge time: 2.5 Hours

Charging port: USB Type-C

Connection modes: 2.4GHz, Bluetooth, Wired

Device name: Lemokey G1