LASKO 2004W (01) PDF MANUAL

Read all instructions before using this Fan.

DO NOT use this Fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints, gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the containers for these products!

ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition should be replaced by a qualified electrician.

ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the Fan when not in use.

BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.

The Blue Plug™ on your Lasko Fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace, repair or tamper with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.

THIS FAN HAS A POLARIZED PLUG (one blade is wider than the other). This plug is designed to fit into the outlet only one way. Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety feature. If the plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced.

AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these devices may overheat and cause a fire hazard.

DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire hazard. Arrange cord away from traffic area and where it will not be tripped over.

ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.

NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.

DO NOT block, cover or obstruct air flow to or from the Fan while in operation.

DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may create a shock hazard.

NEVER use a single extension cord to operate more than one Fan or other electrical device.

DO NOT use this Fan if it has been damaged or is not functioning properly.

THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008). This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.

THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008). This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for hazardous locations.

1. Fan Head Assembly (2002W/2004W)

2. Stand (2002W)

3. Clip (2004W)

Insert the Fan Head Assembly into the top of the Stand until fully seated.

Insert the Fan Head Assembly into the top of the Clip until fully seated.

Turn the Fan Speed Knob to adjust the Fan Speed to 2 (High), 1 (Low), or 0 (OFF).

To adjust head angle: Loosen Knob under Fan Head. Tilt Head to desired air flow position. Retighten Knob.

To Wallmount: Install a Screw (#8 x 3/4″ Wood Screw or equivalent, not supplied) in the wall and hang the Clip on the Screw, as shown.

Always unplug the cord before moving, servicing or cleaning.

NEVER place the Fan in or near water.

Clean the Fan only with a vacuum equipped with a brush attachment; the vacuum will remove the lint and dirt from inside the Fan.

NEVER attempt to take apart the Fan.

Clean the body of the Fan with a soft cloth only.

NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other harsh cleaners.

If your Fan fails to operate, be sure the power cord is plugged into a working electrical outlet. If you have a problem that can not be resolved by the steps listed above, contact Technical Assistance at (800) 233-0268, Monday through Friday, between the hours of 8:00 a.m. and 5:00 p.m. Eastern.

For servicing, other than general user maintenance, please contact Customer Service at (800) 233-0268, Monday through Friday, from 8am-5pm Eastern.

Store the Fan with these instructions, in the original carton in a cool, dry place.

Motor is permanently lubricated.

Corrugated packaging materials are recyclable. For environmentally responsible disposal of this product, contact your local waste service provider.

This Fan is for residential use only. It is not intended to be used in commercial, industrial or agricultural settings.

Read and Save These Instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage!