KUSMAUL 091-198-12-PP (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSMAUL 091-198-12-PP (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** INSTRUCTION MANUAL- AUTO PUMP STATUS cENTER VOLTAGE e PRESSURE PUMP PLUS STATUS CENTER €9 BATTERY CHARGED CHARGING tow O CONDITION BATTERY VOLTAGE AIR TANK PRESSURE MAH = AIR TANK CONDITION MIN KUSSMAUL ELECTRONICS MODE’ # : File: IM_OBI -1 ea-12-PP_revD.indd Rev: D Date: 1 -30-2015 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com a YEAR WARRANTY KUSSMAUL ELECTRONICS ENERGIZED AND READY, WHEN SECONDS couNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 2 ****** INTRODUCTION The Auto Pump Status Center is an air pressure sensor with indicator that displays air pressure in pounds per square inch (PSI). The indicator contains a 2.5-digit numerical display and bar graph. The PSI indicator works in conjuction with an air pressure sensor. The air pressure sensor port can be connected to an air supply to measure and display PSI. Additionally, a 3.5-digit display measures and displays battery voltage. The indicator is designed to be mounted on the exterior of a vehicle so that the battery voltage and PSI condition may be easily viewed. The indicator fits the Kussmaul standard indicator panel cut out. FEATURES l. PUMP PLUS STATUS CENTER Pressure sensor interface with 5/32 air supply input port 2.5-digit PSI display 3.5 digit VOLTAGE display Battery status LEDs 4-segment bar graph II. AIR SUPPLY A 5/32 air supply input port is used to connect air supply to the pressure sensor interface and a 1/8 NPT is provided for connecting to the air tank. Ill. NUMERICAL DISPLAYS A 2.5-digit display provides a PSI reading of the supplied air pressure; additionally a 3.5-digit display provides a voltage reading of the systems battery voltage. IV. BATTERY STATUS LEDs 4 LED’s provide battery condition status: Hi Voltage, Charged, Charging, and Low Voltage. V. BAR GRAPH The 4-segment bar graph is a graphical representation of the aire supply condition. The bottom bar will flash if the supply pressure is below 50 PSI. All bars are illuminated when the pressure reaches 150 PSI. OPERATION The 091-198-12-PP consists of a pressure sensor interface and indicator to measure and display PSI and battery voltage. A bar graph on the indicator provides a graphical representation of the air supply condition, while LEDs provide information on the condition of the battery. During operation, the pressure sensor continuously monitors the air supply present at the air input port. The pressure sensor then genarates an analog signal, which is then sent to the indicator. The indicator then convertes the analog signal to the digital display. A2-pin terminal connector is used to supply power to the pressure sensor interface. Additionally, a 4-pin terminal connector is used to interface the indicator with the pressure sensor. The 4-pin terminal provides power and pressure sensor signal to the indicator. Whenever the monitored air supply drops below 50 PSI the bottom bar graph LED will flash indicating low pressure. The 4-segment bar graph is fully illuminated when the air supply reaches 150 PSI 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 3 ****** INSTALLATION INSTRUCTIONS l. MOUNTING THE AUTO PUMP STATUS CENTER 1. Mount the pressure sensor interface in a suitable location protected from moisture and excessive heat. 2. The indicator is designed to be mounted on the exterior of a vehicle so that the PSI condition may be easily viewed. II. WIRING THE AUTO PUMP STATUS CENTER 1. 2. 3. 4. See figure 1, Wiring the Auto Pump Status Center. Connect the air supply to the air pressure sensor input port using 5/32 tubing. A straight fitting, 1/8 NPT, is supplied for connecting to the air tank. Connect DC input power to the 2-pin terminal. For continuous operation, supply continuous power to the pressure sensor interface. Connect the indicator to the 4-pin terminal located on the pressure sensor interface. 3

****** Page 4 ****** Ill. FIGURE 1: AUTO PUMP STATUS CENTER AIR PRESSURE SENSOR Model 091-198 KUSSMAUL ELECTRONICS POWER OUTPUT 1 % AMP RED (20AWG) FUSE BLACK (20AWG) 2 1 2 3 FROM AIR SUPPLY (5/32 TUBING) 4 Note: recommended 20 AWG cable not supplied 091- 198-12-PP: Wiring Instructions 4

****** Page 5 ****** SPECIFICATIONS Input Voltage: 7-16 VDC (12 VDC nominal) Input Current: 100 mA, maximum Input Fuse: 250 mA (1/4 Amp) Air Supply: 150 PSI, max LED Voltage Set Points. High Voltage: 14.82 VDC and above Charged: 13.08 to 14.82 VDC Charging: 12.84 to 13.08 VDC No LEDs On: 12.30 to 12.84 VDC Low Voltage: 12.30 VDC and below Hardware Pack Provided: (1) PLBPC4-01: Fitting, Straight, 1/8 NPT X 5/32 (36″) WIRI B-201-10: Nylon, M 5/32″ O.D. Tubing Weight: .5 pounds OUTLINE DRAWING 5.25 4,75 3/16″ DIA. INTERFACE INDICATOR a-oo 0 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 6 ****** OPTIONAL ACCESSORIES l. INDICATOR SEAL, MODEL 091-39-109 Provides a waterproof seal for the status center display 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com KUSSMAUL ELECTRONICS ENERGIZED READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 7 ****** INSTALLATION RECORD DATE INSTALLED INSTALLED BY VEHICLE IDENTIFICATION VEHICLE OWNER WARRANTY POI-ICY All products of Kussmaul Electronics are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. Defective products should be returned to Kussmaul Electronics with shipping charges prepaid. Upon repair, products will be returned to customer with shipping charges paid. Kussmaul Electronics shall have no liability for damages of any kind to associated equipment arising from the installation and/or use of the Kussmaul Electronics products. The purchaser, by the acceptance of the equipment, assumes all liabil- ity for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others. Members of fire and Sinergency Manufacturers and Service Association Members of National Fire Protection Members of Fire Apparatus Manufacturers Made in USA 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com Association Association NFPA KUSSMAUL ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT 5 AMA Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com 7


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.