FREE ENGLISH KIA SPORTAGE 2019 (01) PDF USER GUIDE
FREE ENGLISH KIA SPORTAGE 2019 (01) PDF USER MANUAL
FREE ENGLISH KIA SPORTAGE 2019 (01) PDF OWNER GUIDE
FREE ENGLISH KIA SPORTAGE 2019 (01) PDF OWNER MANUAL
FREE ENGLISH KIA SPORTAGE 2019 (01) PDF REFERENCE GUIDE
FREE ENGLISH KIA SPORTAGE 2019 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH KIA SPORTAGE 2019 (01) PDF REFERENCE MANUAL
FREE ENGLISH KIA SPORTAGE 2019 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH KIA SPORTAGE 2019 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD KIA SPORTAGE 2019 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
KIA SPORTAGE 2019 (01) PDF SUMMARY:
How do you use this manual?
The PDF recommends reading the entire manual to get the greatest possible driving pleasure from your vehicle. It is also recommended to pay close attention to the WARNING and CAUTION sections in the manual, and to use the index when looking for a specific area or subject.
What are the fuel requirements for this vehicle?
This vehicle is designed to use only unleaded fuel having a pump octane number ((R+M)/2) of 87 (Research Octane Number 91) or higher, and should not use methanol blended fuels.
What type of gasoline should be used?
The vehicle is designed to obtain maximum performance with UNLEADED FUEL, as well as minimize exhaust emissions and spark plug fouling, and should not add any fuel system cleaning agents to the fuel tank other than what has been specified.
What should I do when refueling?
Do not “top off” after the nozzle automatically shuts off, as forcing more fuel into the tank can cause fuel overflow and a risk of fire. Also, always check that the fuel cap is installed securely to prevent fuel spillage, especially in the event of an accident.
What should you do if using gasoline containing alcohol and methanol?
Do not use gasohol containing more than 15% ethanol, and do not use gasoline or gasohol containing any methanol. If drivability problems occur, discontinue using gasohol of any kind.
What type of fuel is not compatible with this vehicle?
“E85” fuel, which is comprised of 85 percent ethanol and 15 percent gasoline, is not compatible with the vehicle and may result in poor engine performance and damage to the engine and fuel system.
What should you do if you are going to drive this vehicle in another country?
Be sure to observe all regulations regarding registration and insurance and determine that acceptable fuel is available.
What is an event data recorder (EDR)?
The main purpose of an EDR is to record, in certain crash or near crash-like situations, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is designed to record data such as:
- How various systems in your vehicle were operating
- Whether or not the driver and passenger safety belts were buckled/fastened
- How far (if at all) the driver was depressing the accelerator and/or brake pedal
- How fast the vehicle was traveling
What should you do if the vehicle has a manual seat and you want to adjust it?
To move the seat forward or backward, pull the seat slide adjustment lever up and hold it, slide the seat to the desired position, release the lever and make sure the seat is locked in place. To recline the seatback, lean forward slightly and lift up the seatback recline lever, carefully lean back on the seat and adjust the seatback of the seat to the position you desire, then release the lever and make sure the seatback is locked in place. To change the height of the seat, push the lever upwards or downwards.
What should you do if the vehicle has a power seat and you want to adjust it?
Push the control switch forward or backward to move the seat to the desired position. Push the control switch forward or backward to move the seatback to the desired angle. Pull the front portion of the control switch up to raise or press down to lower the front part of the seat cushion, and pull the rear portion of the control switch up to raise or press down to lower the seat cushion.
How do you adjust the lumbar support on the seat?
Press the front portion of the lumbar support switch to increase support, or the rear portion of the switch to decrease support, then release the switch once it reaches the desired position.
How do you adjust the height of the headrest?
To raise the headrest, pull it up to the desired position. To lower the headrest, push and hold the release button on the headrest support and lower the headrest to the desired position.
How do you remove the headrest?
Recline the seatback, raise the headrest as far as it can go, then press the headrest release button while pulling the headrest up.
How do you reinstall the headrest?
Put the headrest poles into the holes while pressing the release button or switch, then recline the seatback and adjust the headrest to the appropriate height.
How do you adjust the height of the rear headrest?
To raise the headrest, pull it up to the desired position. To lower the headrest, push and hold the release button on the headrest support and lower the headrest to the desired position.
How do you remove and reinstall the rear headrest?
To remove the headrest, raise it as far as it can go then press the release button while pulling the headrest upward. To reinstall the headrest, put the headrest poles into the holes while pressing the release button then adjust it to the appropriate height and ensure that it locks in position.
How do you use the armrest?
To use the armrest, pull it forward from the seatback.
How do you fold down the rear seatback?
Set the front seatback to the upright position and if necessary, slide the front seat forward, lower the rear head restraints to the lowest position, insert the rear seat belt buckle in the pocket between the rear seatback and cushion, and insert the rear seat belt webbing in the guide to prevent the seat belt from being damaged, then lift up the front portion of the seatback folding lever, then fold the seat toward the front of the vehicle. When returning the seatback to its upright position, always be sure it has locked into position by pushing on the top of the seatback.
How do you use the rear seat after it has been folded?
Lift and push the seatback rearward by lifting up the front portion of the folding lever, and push the seatback firmly until it clicks into place.
How do you fasten the seat belt?
To fasten the seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an audible “click” when the tab locks into the buckle. The seat belt automatically adjusts to the proper length only after the lap belt portion is adjusted manually so that it fits snugly around your hips.
What do you do if you cannot pull out the seat belt from the retractor?
Firmly pull the belt out and release it. Then you will be able to pull the belt out smoothly.
How do you adjust the height of the shoulder belt?
To raise the height adjuster, pull it up. To lower it, push it down while pressing the height adjuster button. Release the button to lock the anchor into position.
How do you fasten the rear center seatbelt?
Extract the tongue plate (A) from the hole on the belt assembly cover, insert the tongue plate (A) into the buckle (A’) until an audible “click" is heard, pull out the tongue plate (B) from the pocket ©, then pull the tongue plate (B) and insert it into the buckle (B’) until an audible “click” is heard.
How do you release the rear center seatbelt?
Press the release button on the buckle (B’) and remove the tongue plate (B), insert the tongue plate (B) into the pocket ©, to retract the rear center seatbelt, insert the tongue plate into the web release hole (A’), then pull up on the seat belt web and allow the webbing to retract automatically, and insert the tongue plate (A) into the hole on the belt assembly cover.
How do you stow the rear seat belt buckles when not in use?
The rear seat belt buckles can be stowed in the pocket between the rear seatback and cushion. The center seat belt can be stowed with the plate and webbing rolled in the pocket between the rear seatback and cushion, and routing the seat belt webbing through the rear seat belt guides will help keep the belts from being trapped behind or under the seats.
What are the three main types of child restraint systems?
The three main types of child restraint systems are rear-facing seats, forward-facing seats, and booster seats.
What should you never do when riding in a vehicle with a child?
Never hold a child in your arms or lap when riding in a vehicle.
What can happen if you hold a child in your arms during a crash?
The violent forces created during a crash will tear the child from your arms and throw the child against the car’s interior.
What should you always use for a child in a vehicle?
Always use a child restraint system which is appropriate for your child’s height and weight.
What should you never do with children in a vehicle?
Never leave children unattended in a vehicle.
What can happen if you leave children unattended in a vehicle?
The car can heat up very quickly, resulting in injuries to the child in the vehicle.
What should you never do with a seat belt?
Do not use one seat belt for two occupants at the same time.
Why should you not use one seat belt for two occupants?
This will eliminate any safety benefit provided by the seat belt to the occupants.
What does a rear-facing child seat provide?
A rear-facing child seat provides restraint with the seating surface against the back of the child.
How does a rear-facing child seat protect a child in an accident?
The harness system holds the child in place, and in an accident, acts to keep the child positioned in the seat and reduces the stress to the neck and spinal cord.
How should all children under age one ride?
All children under age one must always ride in a rear-facing infant child restraint.
What do convertible and 3-in-1 child seats allow you to do?
Convertible and 3-in-1 child seats typically have higher height and weight limits for the rear-facing position, allowing you to keep your child rear-facing for a longer period of time.
What is the best way to keep a child safe in a vehicle?
Continue to use a rear-facing child seat for as long as your child will fit within the height and weight limits allowed by the child seat manufacturer.
When is a child ready for a forward-facing child restraint?
Once your child has outgrown the rear-facing child restraint, your child is ready for a forward-facing child restraint with a harness.
How does a forward-facing child seat provide restraint for a child?
A forward-facing child seat provides restraint for the child’s body with a harness.
How long should children stay in a forward-facing child seat with a harness?
Keep children in a forward-facing child seat with a harness until they reach the top height or weight limit allowed by your child restraint’s manufacturer.
When is a child ready for a booster seat?
Once your child outgrows the forward-facing child restraint, your child is ready for a booster seat.
What is a booster seat designed to do?
A booster seat is a restraint designed to improve the fit of the vehicle’s seat belt system.
How does a booster seat position the seat belt?
A booster seat positions the seat belt so that it fits properly over the lap of your child.
How long should a child stay in a booster seat?
Keep your child in a booster seat until they are big enough to sit in the seat without a booster and still have the seat belt fit properly.
How should a lap belt fit properly?
The lap belt must lie snugly across the upper thighs, not the stomach.
How should a shoulder belt fit properly?
The shoulder belt should lie snug across the shoulder and chest and not across the neck or face.
Where should children under age 13 always ride?
Children under age 13 must always ride in the rear seats.
How should children always be restrained?
Children under age 13 must always be properly restrained to minimize the risk of injury.
What should you do after selecting a proper child seat for your child?
After selecting a proper child seat for your child, check to make sure it fits properly in your vehicle.
What instructions should you follow when installing the child seat?
Follow the instructions provided by the manufacturer when installing the child seat.
How should the child restraint be secured to the vehicle?
All child restraints must be secured to the vehicle with the lap part of a lap/shoulder belt or with the LATCH system.
How can you make sure the child restraint is firmly secured?
After installing a child restraint to the vehicle, push and pull the seat forward and from side-to-side to verify that it is securely attached to the seat.
How should a child restraint secured with a seat belt be installed?
A child restraint secured with a seat belt should be installed as firmly as possible.
Is some side-to-side movement expected with a child restraint secured with a seat belt?
Some side-to-side movement can be expected.
How should you secure the child in the child restraint?
Make sure the child is properly strapped in the child restraint according to the manufacturer instructions.
What does the LATCH system do?
The LATCH system holds a child restraint during driving and in an accident.
What is the LATCH system designed to do?
This system is designed to make installation of the child restraint easier and reduce the possibility of improperly installing your child restraint.
How does the LATCH system work?
The LATCH system uses anchors in the vehicle and attachments on the child restraint.
What does the LATCH system eliminate the need to use?
The LATCH system eliminates the need to use seat belts to secure the child restraint to the rear seats.
What are lower anchors?
Lower anchors are metal bars built into the vehicle.
How many lower anchors are there for each LATCH seating position?
There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments.
What must you have to use the LATCH system in your vehicle?
To use the LATCH system in your vehicle, you must have a child restraint with LATCH attachments.
Where can you find instructions on how to use the child seat with its attachments for the LATCH lower anchors?
The child seat manufacturer will provide you with instructions on how to use the child seat with its attachments for the LATCH lower anchors.
Where are LATCH anchors provided?
LATCH anchors have been provided in the left and right outboard rear seating positions.
Where are the LATCH anchors located?
The LATCH anchors are located between the seatback and the seat cushion of the rear seat left and right outboard seating positions.
Are there LATCH anchors provided for the center rear seating position?
There are no LATCH anchors provided for the center rear seating position.
Where should you never attempt to attach a LATCH equipped seat?
Never attempt to attach a LATCH equipped seat in the center seating position.
Where are LATCH lower anchors only to be used?
LATCH lower anchors are only to be used in the left and right rear outboard seating positions.
What can happen if you attempt to attach a LATCH equipped seat in the center seating position?
You may damage the anchors or the anchors may fail and break in a collision.
Where are the lower anchor position indicator symbols located?
The lower anchor position indicator symbols are located on the left and right rear seat backs to identify the position of the lower anchors in your vehicle.
How do you use the lower anchor?
To use the lower anchor, push the upper portion of the lower anchor cover.
What are the steps to install a LATCH-compatible child restraint in either of the rear outboard seating positions?
- Move the seat belt buckle away from the lower anchors.
- Move any other objects away from the anchors that could prevent a secure connection between the child restraint and the lower anchors.
- Place the child restraint on the vehicle seat, then attach the seat to the lower anchors according to the instructions provided by the child restraint manufacturer.
- Follow the child restraint instructions for properly adjusting and tightening the lower attachments on the child restraint to the lower anchors.
What precautions should you take when using the LATCH system?
- Read and follow all installation instructions provided with your child restraint system.
- To prevent the child from reaching and taking hold of unretracted seat belts, buckle all unused rear seat belts and retract the seat belt webbing behind the child.
- NEVER attach more than one child restraint to a single anchor.
- Always have the LATCH system inspected by your authorized Kia dealer after an accident.
What can happen if a shoulder belt becomes wrapped around a child’s neck?
Children can be strangled if a shoulder belt becomes wrapped around their neck and the seat belt tightens.
What can happen if you attach more than one child restraint to a single anchor?
This could cause the anchor or attachment to come loose or break.
Why should you have the LATCH system inspected after an accident?
An accident can damage the LATCH system and may not properly secure the child restraint.
What is the recommended maximum weight for the LATCH system?
The recommended maximum weight for the LATCH system is 65 lbs. (30 kg).
What should you consider when selecting a proper child restraint?
When selecting a proper child restraint, consider that the maximum total weight of the child plus the child restraint should be less than 65 lbs (30 kg).
How can you determine the MAX child restraint weight?
Child Restraint Weight = 65 – (child’s total weight in lbs.).
How should you first secure a child restraint seat with a “Tether Anchor” system?
First secure the child restraint with the LATCH lower anchors or the seat belt.
What should you do if the child restraint manufacturer recommends that the top tether strap be attached?
If the child restraint manufacturer recommends that the top tether strap be attached, attach and tighten the top tether strap to the top tether strap anchor.
Where are child restraint system top tether anchorages located?
Child restraint system top tether anchorages are located on the back of the rear seatbacks.
What precautions should you take when installing the tether strap?
- Read and follow all installation instructions provided with your child restraint system.
- NEVER attach more than one child restraint to a single tether anchor.
- Do not attach the tether strap to anything other than the correct tether anchor.
- Do not use the tether anchors for adult seat belts or harnesses, or for attaching other items or equipment to the vehicle.
- Always fasten the seatbelts behind the child restraint seat when they are not used to secure the child seat.
What can happen if you attach more than one child restraint to a single tether anchor?
This could cause the anchor or attachment to come loose or break.
What can happen if you do not attach the tether strap to the correct tether anchor?
It may not work properly if attached to something else.
What can happen if you fail to fasten the seatbelts behind the child restraint when they are not in use?
Failure to do so may result in child strangulation.
What are the steps to install the tether anchor?
- Route the child restraint tether strap over the child restraint seat-back. Route the tether strap under the head restraint and between the head restraint posts, or route the tether strap over the top of the vehicle seatback. Make sure the strap is not twisted.
- Connect the tether strap hook to the tether anchor, then tighten the tether strap according to the child seat manufacturer’s instructions to firmly secure the child restraint to the seat.
- Check that the child restraint is securely attached to the seat by pushing and pulling the seat forward and from side-to-side.
When should all child restraints be secured with a lap part of a lap/shoulder belt?
When not using the LATCH system, all child restraints must be secured to a vehicle rear seat with the lap part of a lap/shoulder belt.
Why must you manually pull the seat belt all the way out to shift the retractor to the “Automatic Locking” mode?
Since all passenger seat belts move freely under normal conditions and only lock under extreme or emergency conditions (emergency locking mode), you must manually pull the seat belt all the way out to shift the retractor to the “Automatic Locking” mode to secure a child restraint.
What does the “Automatic Locking” mode help prevent?
The “Automatic Locking” mode will help prevent the normal movement of the child in the vehicle from causing the seat belt to loosen and compromise the child restraint system.
What are the steps to install a child restraint system on the rear seats using a lap/shoulder belt?
- Place the child restraint system on a rear seat and route the lap/shoulder belt around or through the child restraint, following the restraint manufacturer’s instructions. Be sure the seat belt webbing is not twisted.
- Fasten the lap/shoulder belt latch into the buckle. Listen for the distinct “click” sound. Position the release button so that it is easy to access in case of an emergency.
- Slowly allow the shoulder portion of the seat belt to retract and listen for an audible “clicking” or “ratcheting” sound. This indicates that the retractor is in the “Automatic Locking” mode. If no distinct sound is heard, repeat steps 3 and 4.
- Remove as much slack from the belt as possible by pushing down on the child restraint system while feeding the shoulder belt back into the retractor.
- Push and pull on the child restraint system to confirm that the seat belt is holding it firmly in place. If it is not, release the seat belt and repeat steps 2 through 6.
- Double check that the retractor is in the “Automatic Locking” mode by attempting to pull more of the seat belt out of the retractor. If you cannot, the retractor is in the “Automatic Locking” mode.
What should you do if your CRS manufacturer instructs or recommends you to use a tether anchor with the lap/shoulder belt?
If your CRS manufacturer instructs or recommends you to use a tether anchor with the lap/shoulder belt, refer to the previous pages for more information.
When does the retractor automatically switch from the “Automatic Locking” mode to the emergency lock mode?
When the seat belt is allowed to retract to its fully stowed position, the retractor will automatically switch from the “Automatic Locking” mode to the emergency lock mode for normal adult usage.
How do you remove the child restraint?
To remove the child restraint, press the release button on the buckle and then pull the lap/shoulder belt out of the restraint and allow the seat belt to retract fully.
When should you set the retractor to Automatic Lock mode?
Set the retractor to Automatic Lock mode when installing any child restraint system.
What can happen if the retractor is not in the Automatic Locking mode?
If the retractor is not in the Automatic Locking mode, the child restraint can move when your vehicle turns or stops suddenly.
What should you and your passengers always do, even in vehicles with air bags?
Even in vehicles with air bags, you and your passengers must always wear the safety belts provided in order to minimize the risk and severity of injury in the event of a collision or rollover.
When are air bags activated?
Air bags are activated (able to inflate if necessary) only when the ignition switch is turned to the ON or START position.
When do the appropriate air bags inflate?
The appropriate air bags inflate instantly in the event of a serious frontal collision or side collision in order to help protect the occupants from serious physical injury.
What is the air bag designed to deploy based on in normal conditions?
In normal conditions, the airbag is designed to deploy based on certain angle and intensity of the collision.
Will the air bag deploy in every crash or collision situation?
The airbag will deploy based on angle and intensity of the collision. It will not deploy in every crash or collision situations.
How quickly do front air bags inflate and deflate?
The front air bags will completely inflate and deflate in an instant.
What will you most likely see after a collision in regards to the air bags?
It is much more likely that you will simply see the deflated air bags hanging out of their storage compartments after the collision.
When will side and/or curtain air bags inflate?
In addition to inflating in serious side collisions, side and/or curtain air bags will inflate if the sensing system detects a rollover.
What do curtain air bags do during a rollover?
When a rollover is detected curtain air bags will remain inflated longer to help provide protection from ejection, especially when used in conjunction with the seat belts.
Why must air bags inflate rapidly?
In order to help provide protection, the air bags must inflate rapidly.
Why is the speed of air bag inflation a necessary part of the air bag design?
This speed of inflation reduces the risk of serious or life-threatening injuries and is thus a necessary part of the air bag design.
What injuries can air bag inflation cause?
Air bag inflation can also cause injuries which can include facial abrasions, bruises and broken bones because the inflation speed also causes the air bags to expand with a great deal of force.
Under what circumstances can contact with the steering wheel or passenger air bag cause fatal injuries?
There are even circumstances under which contact with the steering wheel or passenger air bag can cause fatal injuries, especially if the occupant is positioned excessively close to the steering wheel or passenger air bag.
What do air bags do when inflated?
When inflated, the air bags make a loud noise and leave smoke and powder in the air inside the vehicle.
Is the smoke and powder from an inflated air bag normal?
This is normal and is a result of the ignition of the air bag inflator.
What may you feel after an air bag inflates?
After the air bag inflates, you may feel substantial discomfort in breathing due to the contact of your chest with both the seat belt and the air bag, as well as from breathing the smoke and powder.
What should you do after impact to reduce discomfort and prevent prolonged exposure to the smoke and powder from an air bag inflation?
Open your doors and/or windows as soon as possible after impact in order to reduce discomfort and prevent prolonged exposure to the smoke and powder.
Is the smoke and powder from an air bag inflation toxic?
Though smoke and powder are non-toxic, it may cause irritation to the skin (eyes, nose and throat, etc).
What should you do if the smoke and powder from an air bag inflation causes skin irritation?
If this is the case, wash and rinse with cold water immediately and consult a doctor if the symptom persists.
What should you not touch immediately after airbag inflation?
Do not touch the air bag storage area’s internal components immediately after airbag inflation.
Why should you not touch the air bag related parts immediately after air bag inflation?
The air bag related parts in the steering wheel, instrument panel and the roof rails above the front and rear doors are very hot.
What can hot air bag components result in?
Hot components can result in burn injuries.
How far back should you sit from the steering wheel?
Sit as far back as possible from the steering wheel while still maintaining comfortable control of your vehicle.
What is the recommended distance from your chest to the steering wheel?
A distance of at least 10" from your chest to the steering wheel is recommended.
What can happen if you fail to sit at least 10 inches away from the steering wheel?
Failure to do so can result in airbag inflation injuries to the driver.
What should you not install or place near air bag deployment areas?
Do not install or place any accessories near air bag deployment areas, such as the instrument panel, windows, pillars, and roof rails.
What can happen to objects placed near air bag deployment areas if the air bag deploys?
Such objects may become dangerous projectiles if the air bag deploys.
Where should you not install a child restraint?
Do not install a child restraint on the front passenger’s seat.
Why should you never place a rear-facing child restraint in the front passenger’s seat?
If the air bag deploys, it would impact the rear-facing child restraint, causing serious or fatal injury.
Why should you not place front-facing child restraints in the front passenger’s seat?
If the front passenger air bag inflates, it could cause serious or fatal injuries to the child.
What is the purpose of the air bag warning light?
The purpose of air bag warning light in your instrument panel is to alert you of a potential problem with your air bag system, which could include your side and/or curtain air bags used for rollover protection.
Where should you install a child restraint system when children are seated in the rear outboard seats of a vehicle equipped with side and/or curtain air bags?
When children are seated in the rear outboard seats of a vehicle equipped with side and/or curtain air bags, install the child restraint system as far away from the door side as possible.
What can happen if the side and/or curtain air bags inflate near a child restraint system?
Inflation of the side and/or curtain air bags could impact the child.
What does the SRS consist of?
The SRS consists of the following components:
- Driver’s front air bag module
- Passenger’s front air bag module
- Side air bag modules
- Curtain air bag modules
- Retractor pre-tensioner assemblies
- Air bag warning light
- SRS control module (SRSCM)/ Rollover sensor
- Front impact sensors
- Side impact sensors
- Side pressure sensors
- PASSENGER AIR BAG “OFF” indicator (Front passenger’s seat only)
- Occupant detection system (Front passenger’s seat only)
- Driver’s and front passenger’s seat belt buckle sensors
- Emergency Fastening Device(EFD)
What should you do if the air bag warning light is illuminated for more than 6 seconds after the ignition is turned on, or if it illuminates during vehicle operation?
If the air bag warning light is illuminated for more than 6 seconds after the ignition is turned on, or of it illuminates during vehicle operation, an SRS component may not be functioning properly and you should have your vehicle checked by an authorized Kia dealer.
What conditions indicate a malfunction in the air bag system?
- The light does not turn on briefly when you turn the ignition ON.
- The light stays on after illuminating for approximately 6 seconds.
- The light comes on while the vehicle is in motion.
- The light blinks when the ignition switch is in ON position.
Where are the front air bag modules located?
The front air bag modules are located both in the center of the steering wheel and in the front passenger’s panel above the glove box.
When will the SRSCM deploy the front air bags?
When the SRSCM detects a sufficiently severe impact to the front of the vehicle, it will automatically deploy the front air bags.
How do the front air bags deploy?
Upon deployment, tear seams molded directly into the pad covers will separate under pressure from the expansion of the air bags. Further opening of the covers then allows full inflation of the air bags.
How does a fully inflated air bag, in combination with a properly worn seat belt, help the occupants?
A fully inflated air bag, in combination with a properly worn seat belt, slows the driver’s or the passenger’s forward motion, reducing the risk of head and chest injury.
What happens after complete inflation of the air bag?
After complete inflation, the air bag immediately starts deflating, enabling the driver to maintain forward visibility and the ability to steer or operate other controls.
What may happen when an air bag deploys?
If an air bag deploys, there may be a loud noise followed by a fine dust released in the vehicle.
Why is fine dust released in the vehicle during an air bag deployment?
These conditions are normal and are not hazardous – the air bags are packed in this fine powder.
What should you do if the dust generated during air bag deployment causes skin or eye irritation?
Always wash all exposed skin areas thoroughly with cold water and a mild soap after an accident in which the air bags were deployed.
What should you not install or place on the steering wheel, instrument panel, or on the front passenger’s panel above the glove box?
Do not install or place any accessories on the steering wheel, instrument panel, or on the front passenger’s panel above the glove box in a vehicle.
What can happen if you place objects on the steering wheel, instrument panel, or on the front passenger’s panel above the glove box?
Such objects may become dangerous projectiles if the air bag deploys.
What should you not place between the front door and the front seat?
Do not place any objects (an umbrella, bag, etc.) between the front door and the front seat.
What can happen to objects placed between the front door and front seat if the side airbag inflates?
Such objects may become dangerous projectiles if the side airbag inflates.
When can the SRS function?
The SRS can function only when the ignition switch is in the ON position.
What should you do if the SRS air bag warning light does not illuminate or remains on continuously?
If the SRS air bag warning light does not illuminate, or continuously remains on after illuminating for about 6 seconds when the ignition switch is turned to the ON position, or after the engine is started, comes on while driving, the SRS is not working properly. If this occurs, have your vehicle immediately inspected by an authorized Kia dealer.
What should you do before replacing a fuse or disconnecting a battery terminal?
Before you replace a fuse or disconnect a battery terminal, turn the ignition switch to the LOCK position and remove the ignition switch.
When should you never remove or replace the air bag related fuse(s)?
Never remove or replace the air bag related fuse(s) when the ignition switch is in the ON position.
What can happen if you do not heed the warning about removing the air bag related fuse(s) when the ignition switch is in the ON position?
Failure to heed this warning will cause the SRS air bag warning light to illuminate.
What is the Occupant Detection System designed to do?
The occupant detection system is designed to detect the presence of a properly-seated front passenger and determine if the passenger’s front air bag should be enabled (may inflate) or not.
Which air bag is controlled by the Occupant Detection System?
Only the front passenger front air bag is controlled by the Occupant Detection System.
What should you not put in front of the passenger air bag indicator?
Do not put anything in front of the passenger air bag indicator.
What are the main components of the occupant detection system?
- A detection device located within the front passenger seat cushion.
- An electronic system which determines whether the passenger air bag system should be activated or deactivated.
- An indicator light located on the instrument panel which illuminates the words PASSENGER AIR BAG “OFF” indicates the front passenger air bag system is deactivated.
- The instrument panel air bag warning light is interconnected with the occupant detection system.
When will the PASSENGER AIR BAG “OFF” indicator turn off?
If the front passenger seat is occupied by a person that the system determines to be of appropriate size, and he/she sits properly (sitting upright with the seatback in an upright position, centered on the seat cushion with their seat belt on, legs comfortably extended and their feet on the floor), the PASSENGER AIR BAG “OFF” indicator will turn off.
What does it mean when the front passenger’s air bag is able to inflate?
When the PASSENGER AIR BAG “OFF” indicator turns off, the front passenger’s air bag will be able to inflate, if necessary, in frontal crashes.
Where will you find the PASSENGER AIR BAG “OFF” indicator?
You will find the PASSENGER AIR BAG “OFF” indicator on the center fascia panel.
What conditions does the occupant detection system detect?
The system detects the following conditions and activates or deactivates the front passenger air bag based on these conditions:
- Failing to sit in an upright position.
- Leaning against the door or center console.
- Sitting with hips shifted toward the front of the seat.
- Placing feet on the front passenger seat back.
- Improperly seated occupants.
- Reclined seat back.
How does the occupant detection system classify a person of adult size?
The system judges a person of adult size as an adult.
How may the system recognize a smaller adult sitting in the front passenger seat?
When a smaller adult sits in the front passenger seat, the system may recognize him/her as a child depending on his/her physique and posture.
Should children be allowed to ride in the front passenger seat?
Do not allow children to ride in the front passenger seat.
How may the system recognize a larger child who has outgrown a child restraint system in the front passenger seat?
When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/her as an adult depending upon his/her physique or sitting position.
Should you install a child restraint system on the front passenger seat?
Never install a child restraint system on the front passenger seat.
When may the PASSENGER AIR BAG “OFF” indicator turn on or off when a child above 12 months to 12 years old sits in the front passenger seat?
The PASSENGER AIR BAG “OFF” indicator may turn on or off when a child above 12 months to 12 years old (with or without child restraint system) sits in the front passenger seat. This is a normal condition.
What are the conditions detected by the occupant classification system, and how do they affect the indicator/warning light and the front passenger air bag?
- Adult – “PASSENGER AIR BAG OFF” indicator light: Off; SRS warning light: Off; Front passenger air bag: Activated.
- Child restraint system with child under 12 months old – “PASSENGER AIR BAG OFF” indicator light: On; SRS warning light: Off; Front passenger air bag: Deactivated.
- Unoccupied – “PASSENGER AIR BAG OFF” indicator light: On; SRS warning light: Off; Front passenger air bag: Deactivated.
- Malfunction in the system – “PASSENGER AIR BAG OFF” indicator light: Off; SRS warning light: On; Front passenger air bag: Activated.
What should you not do with the passenger seat when it is heavily soaked with any type of liquid?
Do not install a child restraint seat in the passenger seat when the seat is heavily soaked with any type of liquid.
What should you not do with the ODS (Occupant Detection System)?
Do not alter or remodel the ODS (Occupant Detection System).
What can happen if you alter or remodel the ODS?
This may damage the system and prevent it from functioning properly in a collision.
What should you not use on car seats?
Do not use car seat cushions that cover up the surface of the seat and aftermarket manufactured passenger seat heaters.
What should you do after conducting car interior cleaning using steam or detergent?
After conducting car interior cleaning using steam or detergent, the seat should be dried properly. Afterward, check for normal operation of the “PASS AIR BAG “OFF”” and air bag warning lights.
Where should any service related to the passenger seat and the ODS be done?
Any service related to the passenger seat and the ODS must be done at a Kia service center.
What should you check after the passenger seat has been removed or installed for repair purposes?
After the passenger seat has been removed or installed for repair purposes, check for normal operation of the “PASS AIR BAG “OFF”” and air bag warning lights with a person seated or not seated in the passenger seat.
What happens when the “PASS AIR BAG “OFF”” symbol is illuminated?
When the “PASS AIR BAG “OFF”” symbol is illuminated, the passenger air bag system will not operate.
When will the passenger air bag system operate?
The passenger air bag system will operate when necessary if the symbol is not illuminated.
What should you not do with the front passenger seat?
Do not modify or replace the front passenger seat.
What should you not place on or attach to the front passenger seat?
Don’t place anything on or attach anything such as a blanket, front seat cover or after market seat heater to the front passenger seat.
What can happen if you place or attach things on the front passenger seat?
This can adversely affect the occupant detection system.
How do I unlock the vehicle using the door handle button?
Carry the smart key, press the button of the driver’s outside door handle, the driver’s door will unlock, the hazard warning lights will blink and the chime will sound two times. Press the button twice within 4 seconds and all doors and the lift-gate will unlock and the hazard warning lights will blink and the chime will sound two times.
What is the operating range for the door handle button?
The button will only operate when the smart key is within 28~40in. (0.7 ~ 1 m) from the outside door handle.
What happens if the smart key is recognized near the front door handle?
When the smart key is recognized in the area of 28 ~ 40 in. (0.7 ~ 1 m) from the front outside door handle, other people can also open the doors.
What happens to the doors after unlocking?
After unlocking the driver’s door or all doors, the door(s) will lock automatically unless the door is opened.
How do I unlock the vehicle using the button on the smart key?
Press the unlock button of the smart key, the driver’s door will unlock, the hazard warning lights will blink and the chime will sound two times. Press the unlock button twice within 4 seconds and all doors and the liftgate will unlock. The hazard warning lights will blink and the chime will sound two times.
What happens if no door is opened after pressing the unlock button?
After pressing the button, the doors will lock automatically unless any door is opened within 30 seconds.
What is the Two Turn Unlock function?
The Two Turn Unlock function can be activated or deactivated. Refer to “User settings” in the PDF.
How do I unlock the liftgate using the liftgate handle button?
Carry the smart key and press the liftgate handle button. When all doors are locked, the hazard warning lights will blink two times. Once the liftgate is opened and then closed, the liftgate will lock automatically.
What is the operating range for the liftgate handle button?
The button will only operate when the smart key is within 28 ~ 40 in. (0.7 ~ 1 m) from the liftgate handle.
How do I unlock the liftgate using the button on the smart key?
Press the liftgate unlock button for more than 1 second. When all doors are locked, the hazard warning lights will blink two times.
How do I open the power liftgate?
The Power Liftgate will open if the button is pressed for more than 1 second. Also, once the liftgate is opened and then closed, the liftgate will be locked again automatically.
How do I use the panic button on the smart key?
Press the panic button for more than 1 second. The horn sounds and hazard warning lights flash for about 27 seconds.
How do I stop the horn and lights when the panic button is activated?
To stop the horn and lights, press any button on the smart key.
How many smart keys can be registered to a single vehicle?
A maximum of 2 smart keys can be registered to a single vehicle.
What should I do if I lose my smart key?
If you lose your smart key, you will not be able to start the engine. You should immediately take the vehicle and remaining key to your authorized Kia dealer (tow the vehicle, if necessary) to protect it from potential theft.
What can cause the smart key to not work?
- The smart key is close to a radio transmitter such as a radio station or an airport which can interfere with normal operation of the smart key.
- The smart key is near a mobile two way radio system or a cellular phone.
- Another vehicle’s smart key is being operated close to your vehicle.
- If the smart key is in close proximity to your cellular phone or smart phone, the signal from the smart key could be blocked by normal operation of your cellular phone or smart phone.
What should I do if the smart key does not work correctly?
Open and close the door with the mechanical key and contact an authorized Kia dealer.
What should I do to maintain the smart key properly?
Avoid placing the smart key and your cellular phone or smart phone in the same pants or jacket pocket and maintain adequate distance between the two devices.
What happens if the keyless entry system is inoperative due to water or liquids?
It will not be covered by your manufacturer’s vehicle warranty.
What precautions should I take with the transmitter?
Keep the transmitter away from water or any liquid as it can become damaged and not function properly.
How do I replace the battery in the smart key?
Remove the mechanical key, pry open the rear cover, replace the battery with a new battery (CR2032) making sure the battery is in the correct position, and install the battery in the reverse order of removal.
What should I do if I am unsure how to use my smart key or replace the battery?
Contact an authorized Kia dealer.
What can cause the smart key to malfunction?
The smart key can malfunction if exposed to moisture or static electricity.
What type of battery should I use for the smart key?
Be sure to use the correct battery.
What precautions should I take when handling the smart key?
To avoid damaging the smart key, don’t drop it, get it wet, or expose it to heat or sunlight.
How should I dispose of the smart key battery?
Dispose of the battery according to your local law(s) or regulation.
What is the smart key immobilizer system?
Your vehicle is equipped with an electronic engine immobilizer system to reduce the risk of unauthorized vehicle use. It is comprised of a small transponder in the smart key and electronic devices inside the vehicle.
How does the immobilizer system work?
When you turn the engine start/stop button to the ON position by pressing the button while carrying the smart key, it verifies if the smart key is valid or not. If the key is determined to be valid, the engine will start. If the key is determined to be invalid, the engine will not start.
What can damage the smart key?
Do not drop, get wet or expose the smart key to heat or sunlight, or it will be damaged.
How do I deactivate the immobilizer system?
Turn the engine start/stop button to the ON position by pressing the button while carrying the smart key.
How do I activate the immobilizer system?
Turn the engine start/stop button to the OFF position. The immobilizer system activates automatically.
What should I do when starting the engine with the smart key?
When starting the engine, do not use the key with other immobilizer keys around. Otherwise the engine may not start or may stop soon after it starts. Keep each key separate in order to avoid a starting malfunction.
What should I do if I need additional keys or lose my keys?
Contact an authorized Kia dealer.
What are the conditions for the device to comply with FCC rules?
This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.
What can void the user’s authority to operate the equipment?
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
What happens if the keyless entry system is inoperative due to unapproved changes?
It will not be covered by your manufacturer’s vehicle warranty.
What are the three stages of the theft-alarm system?
The first is the “Armed” stage, the second is the “Theft-alarm” stage, and the third is the “Disarmed” stage.
What does the theft-alarm system do when triggered?
If triggered, the system provides an audible alarm with blinking of the hazard warning lights.
How do I arm the theft-alarm system?
Remove the ignition key from the ignition switch and exit the vehicle, make sure that all doors (and liftgate) and engine hood are closed and latched, then lock the doors using the transmitter of the keyless entry system (or smart key) or ignition key.
How do I know if the system is armed?
After completion of the steps above, the hazard warning lights will blink (for smart key, the chime also sounds) once to indicate that the system is armed.
What happens if a door or hood is not closed properly when arming the system?
If any door (or liftgate) or engine hood remains open, the hazard warning lights and the chime will not operate and the theft-alarm will not arm.
Can the theft-alarm system be armed by locking the doors with the key?
Yes, the system can also be armed by locking the doors with the key from the front doors; however, the hazard warning lights will not blink using this method.
Can the theft-alarm system be deactivated?
The theft-alarm system can be deactivated by an authorized Kia dealer. If you want this feature, consult an authorized Kia dealer.
What should I do before arming the system?
Do not arm the system until all passengers have left the vehicle. If the system is armed while a passenger(s) remains in the vehicle, the alarm may be activated when the remaining passenger(s) leave the vehicle.
What happens if a door or hood is opened within 30 seconds after arming?
If any door (or liftgate ) or engine hood is opened within 30 seconds after the system enters the armed stage, the system is disarmed to prevent an unnecessary alarm.
What will activate the theft-alarm?
- A front or rear door is opened without using the ignition key or transmitter (or smart key).
- The liftgate is opened without using the transmitter (or smart key).
- The engine hood is opened.
What happens when the theft-alarm is activated?
The horn will sound and the hazard warning lights will blink continuously for approximately 27 seconds, and repeat the horn 3 times unless the system is disarmed.
How do I turn off the theft-alarm?
To turn off the system, unlock the doors with the ignition key or transmitter (or smart key).
How is the theft-alarm system disarmed?
The system will be disarmed when the doors (and liftgate) are unlocked with the transmitter (or smart key) or the ignition key.
How do I know if the system is disarmed?
After depressing the unlock button, the hazard warning lights will blink and the chime will sound twice (in smart key) to indicate that the system is disarmed.
What happens if a door is not opened within 30 seconds after disarming?
After depressing the unlock button, if any door (or liftgate) is not opened within 30 seconds, the system will be rearmed.
What happens if I try to start the engine while the alarm is activated?
The vehicle starting motor is disabled during the theft-alarm stage.
How do I disarm the system if I do not have the transmitter?
- If the system is not disarmed with the transmitter, insert the key into the ignition switch, turn the ignition switch to the ON position and wait for 30 seconds. Then the system will be disarmed.
- If the system is not disarmed with the smart key, press the engine start/stop button with smart key. The side with the lock button should contact the engine start/stop button directly.
What should I do if I lose my keys?
Consult your authorized Kia dealer.
What happens if the theft-alarm system malfunctions due to improper alterations?
Malfunctions caused by improper alterations, adjustments or modifications to the theft-alarm system are not covered by your vehicle manufacturer warranty.
What should I do if the theft-alarm system needs to be serviced?
Do not change, alter or adjust the theft-alarm system because it could cause the theft-alarm system to malfunction and should only be serviced by an authorized Kia dealer.
How do I remove the door lock cover (Type C)?
Pull out the door handle, press the lever located inside the bottom part of the cover with a key or flat-head screwdriver, and push out the cover while pressing the lever.
How do I unlock and lock the doors using the key?
Turn the key toward the rear of the vehicle to unlock and toward the front of the vehicle to lock.
What happens if I lock/unlock the driver’s door with a key?
If you lock/unlock the driver’s door with a key, all vehicle doors will lock/unlock automatically.
How else can the doors be locked and unlocked?
Doors can also be locked and unlocked with the transmitter.
How do I open the doors after they are unlocked?
Once the doors are unlocked, they may be opened by pulling the door handle.
How do I close the doors?
When closing the door, push the door by hand. Make sure the doors are closed securely.
What can cause door lock and door mechanisms to not work properly?
In cold and wet climates, door lock and door mechanisms may not work properly due to freezing conditions.
What happens if the door is locked/unlocked multiple times in rapid succession?
If the door is locked/unlocked multiple times in rapid succession with either the vehicle key or door lock switch, the system may stop operating temporarily in order to protect the circuit and prevent damage to system components.
What should I do if people must spend a longer time in the vehicle while it is very hot or cold outside?
Do not lock the vehicle from the outside when there are people in it.
What should I do before driving?
Securely close your door before you begin driving. Failure to fully close your door may cause it to open during vehicle operation.
What should I be aware of when closing the door?
Keep your body out of the way of the closing door to prevent injuries.
What can happen if I open and close the door repeatedly with excessive force?
Do not open and close the door repeatedly if unnecessary or with excessive force. Such action can damage the vehicle door.
How do I lock a door without the key?
Push the inside door lock button or central door lock switch to the “Lock” position when the ignition switch is in the OFF position and close the door.
What happens if I lock the door with the central door lock switch?
If you lock the door with the central door lock switch, all vehicle doors will lock automatically.
What should I always do when leaving your vehicle unattended?
Always remove the ignition key, engage the parking brake, close all windows, and lock all doors when leaving your vehicle unattended.
How do I unlock a door from inside the vehicle?
To unlock a door, push the door lock button to the “Unlock” position. The red mark on the button will be visible.
How do I lock a door from inside the vehicle?
To lock a door, push the door lock button to the “Lock” position. If the door is locked properly, the red mark on the door lock button will not be visible.
How do I open a door from the inside?
To open a door, pull the door handle outward.
What happens if the inner door handle of the driver’s (or front passenger’s) door is pulled when the door lock button is in the lock position?
The button will unlock and the door will open.
Can the front doors be locked if the ignition key is in the ignition switch and any front door is opened?
Front doors cannot be locked if the ignition key is in the ignition switch and any front door is opened.
Can the doors be locked if the smart key is in the vehicle and a door is open?
Doors cannot be locked if the smart key is in the vehicle and an door is open.
What should I do if a power door lock fails while I am in the vehicle?
- Operate the door unlock feature repeatedly (both electronic and manual) while simultaneously pulling on the door handle.
- Operate the other door locks and handles, front and rear.
- Lower a front window and use the key to unlock the door from outside.
How do I operate the central door lock switch?
When pressing the right portion for driver side or the upper portion for passenger side of the switch, all vehicle doors will lock. When pressing the left portion for driver side or the lower portion for passenger side of the switch, all vehicle doors will unlock.
What happens if the key is in the ignition switch (or if the smart key is in the vehicle) and any door is opened?
If the key is in the ignition switch (or if the smart key is in the vehicle) and any door is opened, the doors will not lock even though the central door lock switch is pressed.
What should I not do with the inner door handle while the vehicle is moving?
Do not pull the inner door handle of driver’s(or passenger’s) door while the vehicle is moving.
What happens to the doors in the event of air bag deployment?
In the event of air bag deployment resulting from a vehicle impact, all doors will automatically unlock.
What happens to the doors when the vehicle exceeds 10 mph (15 km/h)?
All doors will automatically lock after the vehicle speed exceeds 10 mph (15 km/h).
Where can I select auto door lock/unlock features?
You can select some auto door lock/unlock features in “User Settings”. Refer to “User Settings” in the PDF.
What should I never do with children or animals in the vehicle?
Never leave children or animals unattended in your vehicle. An enclosed vehicle can become extremely hot, causing death or severe injury to unattended children or animals who cannot escape the vehicle.
What should I ensure when the vehicle is in motion?
The doors should always be fully closed and locked while the vehicle is in motion to prevent accidental opening of the door.
What should I be careful of when opening doors?
Be careful when opening doors and watch for vehicles, motorcycles, bicycles or pedestrians approaching the vehicle in the path of the door. Opening a door when something is approaching can cause damage or injury.
What is the purpose of the child-protector rear door lock?
The child safety lock is provided to help prevent children from accidentally opening the rear doors from inside the vehicle. The rear door safety locks should be used whenever children are in the vehicle.
How do I engage the child safety lock?
Open the rear door, turn the child safety lock located on the rear edge of the door to the lock position, and close the rear door.
What happens when the child safety lock is in the lock position?
When the child safety lock is in the lock position, the rear door will not open even when the inner door handle is pulled.
How do I open the rear door when the child safety lock is engaged?
To open the rear door, pull the outside door handle.
What should I always do when children are in the vehicle?
Use the rear door safety locks whenever children are in the vehicle. If a child accidentally opens the rear doors while the vehicle is moving, they may fall out.
How is the liftgate locked or unlocked?
The liftgate is locked or unlocked when all doors are locked or unlocked with the key, transmitter (or smart key) or central door lock switch.
How do I open the liftgate?
If unlocked, the liftgate can be opened by pressing the handle switch and then pulling the handle up.
How do I unlock only the liftgate?
Only the liftgate is unlocked if the liftgate unlock button on the smart key is pressed (if equipped). Once the liftgate is opened and then closed, the liftgate is locked automatically.
What should I be aware of when opening the liftgate?
The liftgate swings upward. Make sure no objects or people are near the rear of the vehicle when opening the liftgate.
What can cause the liftgate to not work properly?
In cold and wet climates, door lock and door mechanisms may not work properly due to freezing conditions.
How do I close the liftgate?
To close the liftgate, lower and push down the liftgate firmly. Make sure that the liftgate is securely latched.
What should I be aware of when closing the liftgate?
Make sure your hands, feet and other parts of your body are safely out of the way before closing the liftgate.
What can happen if I drive with the liftgate not closed?
Possible damage may occur to the liftgate lift cylinders and attached hardware if the liftgate is not closed prior to driving.
What is the emergency liftgate safety release?
Your vehicle is equipped with an emergency liftgate safety release lever located on the bottom of the liftgate. When someone is inadvertently locked in the cargo area, the liftgate can be opened by pushing the release lever and pushing open the liftgate.
Where should occupants not ride in the vehicle?
Occupants should never ride in the rear cargo area where no restraints are available. Occupants should always be properly restrained.
What can happen if I drive with the liftgate open?
Driving with the liftgate open is not advisable. Dangerous exhaust fumes can enter the passenger compartment. If you must drive with the liftgate opened, keep the air vents and all windows open so that additional outside air can enter.
When should I use the liftgate release lever?
Use the release lever for emergencies only. Use with extreme caution, especially while the vehicle is in motion.
What should I be aware of when closing the liftgate?
Make sure nothing is near the liftgate latch and striker while closing the liftgate. It may damage the liftgate’s latch.
What are the controls for the power liftgate?
- Power liftgate open / close button
- Power liftgate handle switch
- Power liftgate close button
When will the power liftgate operate?
If the ignition is ON, the power liftgate operates when the automatic shift lever is in P (Park).
What can cause the power liftgate to not work properly?
In cold and wet climates, power liftgate may not work properly due to freezing conditions.
What should I not do with heavy objects on the power liftgate?
Do not attach heavy objects to the power liftgate when you operate the power liftgate. Weight on liftgate could cause damages to the system.
What should I never do with children or animals near the power liftgate?
Never leave children or animals unattended in your vehicle. Children or animals might operate the power liftgate in such a way that could result in injury to themselves or others or damage to the vehicle.
How can the power liftgate be opened automatically?
- Press and hold the liftgate unlock button on the transmitter or smart key until power liftgate operates.
- Press the power liftgate open/close button for approximately one second.
- While power liftgate operating, you can stop it if you shortly press the unlock button on the transmitter or smart key.
- For emergency stop while power liftgate operating, press the power liftgate open/close button shortly.
What should I not do when the power liftgate is in automatic operation?
Do not close or open the power liftgate manually during automatic operation. This may cause damage to the power liftgate or to the vehicle.
How should I operate the power liftgate manually when the battery is discharged or disconnected?
If it is necessary to close or open the power liftgate manually when the battery is discharged or disconnected, make sure the liftgate is not in operation. Switch the power liftgate to the off position. Do not apply excessive force.
How do I open the power liftgate with the handle switch?
Press the liftgate handle switch carrying the smart key with you.
How do I close the power liftgate?
Press the power liftgate close button for approximately one second when the liftgate is opened. The liftgate will close and lock automatically. For emergency stop while power liftgate operating, press the power liftgate open/close button shortly.
What conditions will prevent the power liftgate from opening automatically?
The power liftgate will not open automatically, when the vehicle is moving more than 2mph(3km/h) or the automatic shift lever is not in P(Park) position.
What happens if I drive over 2 mph (3 km/h) with the liftgate open?
The chime will sound continuously if you drive over 2 mph (3 km/h) with the liftgate opened. Stop your vehicle at a safe place as soon as possible to check if your liftgate is opened.
Can the power liftgate be operated when the engine is not running?
The power liftgate can be operated when the engine is not running. However the power liftgate operation consumes large amounts of vehicle electric power. To prevent the battery from being discharged, do not operate it excessively.
What should I do to prevent the battery from being discharged when operating the power liftgate?
To prevent the battery from being discharged, do not leave the power liftgate in the open position for a long time.
Should I modify or repair the power liftgate myself?
Do not modify or repair any part of the power liftgate by yourself. This must be done by an authorized Kia dealer.
What should I do when jacking up the vehicle?
When jacking up the vehicle to change a tire or repair the vehicle, do not operate the power liftgate. This could cause the power liftgate to operate improperly.
What can cause the power liftgate to not work properly?
In cold and wet climates, the power liftgate may not work properly due to freezing conditions.
Should I wait until the power liftgate is fully closed before starting the vehicle?
It is recommended to wait until the power liftgate is fully closed before starting the vehicle. The power liftgate may not close fully if the vehicle is started during automatic closing.
What happens if I operate the power liftgate more than 5 times continuously?
Do not operate the power liftgate more than 5 times continuously. It may damage the power liftgate system. If you operate the power liftgate more than 5 times continuously, the chime will sound 3 times and the power liftgate will not operate. At this time, stop operating the liftgate and leave it for more than 1 minute.
What should I be aware of before opening or closing the power liftgate?
Make sure there are no people or objects around the liftgate before opening or closing the power liftgate. Wait until the liftgate is open fully and stopped before loading or unloading cargo from the vehicle.
What is the automatic reversal feature of the power liftgate?
During power opening and closing if the power liftgate is blocked by an object or part of the body, the power liftgate will detect the resistance.
What happens if the resistance is detected while opening the liftgate?
If the resistance is detected while opening the liftgate, it will stop and move in the opposite direction.
What happens if the resistance is detected while closing the liftgate?
If the resistance is detected while closing the liftgate, it will stop and move in the opposite direction.
What happens if the resistance is weak, or the liftgate is near the latched position?
If the resistance is weak such as from an object that is thin or soft, or the liftgate is near the latched position, the automatic stop and reversal may not detect the resistance.
What happens if the automatic reversal feature operates continuously more than twice?
If the automatic reversal feature operates continuously more than twice during opening or closing operation, the power liftgate may stop at that position. At this time, close the liftgate manually and operate the liftgate automatically again.
How do I reset the power liftgate?
Put the automatic shift lever in P (Park). While pressing the liftgate close button, press the liftgate handle switch for more than 3 seconds. (the chime will sound). Close the liftgate manually.
What should I do if the power liftgate does not work properly after resetting it?
If the power liftgate does not work properly after the above procedure, have the system checked by an authorized Kia dealer.
What condition should I check before using the power liftgate?
Make sure the automatic shift lever is in P (Park).
What should I never place in the path of the power liftgate?
Never place any object or part of your body in the path of the power liftgate as it is operating. Doing so could result in personal injury or damage to the vehicle. Never operate power liftgate attached with any heavy objects (ex. Bicycles). It could damage the power liftgate.
How do I set the power liftgate opening height?
Position the liftgate manually to the height you prefer, press the liftgate close button for more than 3 seconds, close the liftgate manually after hearing the buzzer sound. The liftgate will open to the height the driver has set up.
What is the Smart Power Liftgate system?
On a vehicle equipped with a smart key, the liftgate can be opened using the Smart Power Liftgate system.
How can I open the liftgate with the Smart Power Liftgate?
The liftgate can be opened with no-touch activation satisfying all the conditions below:
- After 15 seconds when all doors are closed and locked
- Positioned in the detecting area for more than 3 seconds
When does the Smart Power Liftgate not operate?
- The smart key is detected within 15 seconds after the doors are closed and locked, and is continuously detected.
- The smart key is detected within 15 seconds after the doors are closed and locked, and within 60 inches (1.5 m) from the front door handles (for vehicles equipped with Welcome Light).
- A door is not locked or closed.
- The smart key is in the vehicle.
How do I activate the Smart Power Liftgate?
To activate the Smart Power Liftgate, go to User Settings Mode and select Smart Power Liftgate on the LCD display. Refer to the “LCD Display” section in the PDF for more information.
What happens when the smart key is detected in the detecting area?
If you are positioned in the detecting area (20 ~ 40 inches (50 ~ 100 cm) behind the vehicle) carrying a smart key, the hazard warning lights will blink and chime will sound for about 3 seconds to alert you the smart key has been detected and the liftgate will open.
What should I do if I do not want the liftgate to open?
Do not approach the detecting area if you do not want the liftgate to open. If you have unintentionally entered the detecting area and the hazard warning lights and chime starts to operate, leave the detecting area with the smart key. The liftgate will stay closed.
What happens after the smart key is detected in the detecting area?
The hazard warning lights will blink and chime will sound 2 times and then the liftgate will open.
What should I do before driving?
Make sure you close the liftgate before driving your vehicle.
What should I make sure of before opening or closing the liftgate?
Make sure there are no people or objects around the liftgate before opening or closing the liftgate.
What should I be aware of when opening the liftgate on a slope?
Make sure objects in the liftgate do not come out when opening the liftgate on a slope. It may cause serious injury.
What should I do when washing my vehicle to prevent accidental opening of the liftgate?
Make sure to deactivate the Smart Power Liftgate when washing your vehicle. Otherwise, the liftgate may open inadvertently.
Where should I keep the smart key?
The key should be kept out of reach of children. Children may inadvertently open the Smart Power Liftgate while playing around the rear area of the vehicle.
How do I deactivate the Smart Power Liftgate function using the smart key?
If you press any button of the smart key during the Detect and Alert stage, the Smart Power Liftgate function will be deactivated.
How do I temporarily deactivate the Smart Power Liftgate function?
If you press the door unlock button, the Smart Power Liftgate function will be deactivated temporarily. But, if you do not open any door for 30 seconds, the smart power liftgate function will be activated again.
How do I open the liftgate if the Smart Power Liftgate is deactivated?
If you press the liftgate open button for more than 1 second, the liftgate opens.
What happens if I press the door lock or liftgate open button when the Smart Power Liftgate is not in the Detect and Alert stage?
If you press the door lock button or liftgate open button when the Smart Power Liftgate function is not in the Detect and Alert stage, the smart power liftgate function will not be deactivated.
How can the Smart Power Liftgate function be activated again if it was deactivated and a door was opened?
In case you have deactivated the Smart Power Liftgate function by pressing the smart key button and opened a door, the smart power liftgate function can be activated again by closing and locking all doors.
What is the detecting range of the Smart Power Liftgate?
The Smart Power Liftgate operates with a welcome alert if the smart key is detected within 20 ~ 40 inches (50 ~ 100 cm) from the liftgate.
How do I reprogram a single HomeLink button?
To reprogram a device to HomeLink using a HomeLink button previously trained, follow these steps:
- Press and hold the desired HomeLink button. Do NOT release until step 4 has been completed.
- When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 2-8 cm (1 to 3 inches) away from the HomeLink surface.
- Press and hold the hand-held transmitter button (or press and “cycle” – as described in “Canadian Programming”).
- The HomeLink indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons. The previous device has now been erased and the new device can be activated by pushing the HomeLink button that has just been programmed. This procedure will not affect any other programmed HomeLink buttons.
How do I program my garage or gate opener in Canada?
During programming, your hand-held transmitter may automatically stop transmitting. Continue to press and hold the HomeLink button (note steps 2 through 4 in the “Programming” portion of this text) while you press and re-press (“cycle”) your handheld transmitter every two seconds until the frequency signal has been learned. The indicator light will flash slowly and then rapidly after several seconds upon successful training.
Where can I find more information on the HomeLink Wireless Control System?
If you would like additional information on the HomeLink Wireless Control System, HomeLink compatible products, or to purchase other accessories such as the HomeLink® Lighting Package, please contact HomeLink at 1-800-355-3515 or on the internet at http://www.homelink.com.
What are the FCC rules for this device?
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
What should I do before driving?
Be sure to adjust the mirror angles before driving.
How do I adjust the outside rearview mirrors remotely?
The mirrors can be adjusted remotely with the remote switch.
How do I prevent damage to the mirror heads during an automatic car wash?
The mirror heads can be folded back to prevent damage during an automatic vehicle wash or when passing through a narrow street.
What should I do if the mirror is jammed with ice?
If the mirror is jammed with ice, do not adjust the mirror by force. Use an approved spray de-icer (not radiator antifreeze) to release the frozen mechanism or move the vehicle to a warm place and allow the ice to melt.
How do I remove ice from the mirror face?
Do not scrape ice off the mirror face; this may damage the surface of the glass. If ice should restrict the movement of the mirror, do not force the mirror for adjustment. To remove ice, use a deicer spray, or a sponge or soft cloth with very warm water.
When should I not adjust or fold the outside rearview mirrors?
Do not adjust or fold the outside rearview mirrors while the vehicle is moving. This could result in loss of control.
How do I adjust the position of the outside rearview mirrors using the electric remote control mirror switch?
To adjust the position of either mirror, press the R or L button (1) to select the right side mirror or the left side mirror, then press a corresponding point ( ) on the mirror adjustment control to position the selected mirror up, down, left or right. After adjustment, put the button into neutral (center) position to prevent inadvertent adjustment.
How do I fold or unfold the outside rearview mirrors using the electric type mirror switch?
The outside rearview mirror can be folded or unfolded by pressing the switch when the ignition switch is ACC or ON position as below: Left (1) : The mirror will unfold. Right (2) : The mirror will fold.
What happens when the mirrors reach their maximum adjusting angles?
The mirrors stop moving when they reach the maximum adjusting angles, but the motor continues to operate while the switch is pressed. Do not press the switch longer than necessary, the motor may be damaged.
Should I attempt to adjust the outside rearview mirror by hand?
Do not attempt to adjust the outside rearview mirror by hand. Doing so may damage the parts.
How do the outside rearview mirrors fold or unfold automatically?
The mirror will fold or unfold when the door is locked or unlocked by the folding key or smart key. The mirror will fold or unfold when the door is locked or unlocked by the button on the outside door handle. The mirror will unfold when you approach the vehicle (all doors closed and locked) with a smart key in possession (if equipped).
What should I do to prevent unnecessary battery discharge when adjusting electric mirrors?
The electric type outside rearview mirror operates even though the engine start/stop button is in the OFF position. However, to prevent unnecessary battery discharge, do not adjust the mirrors longer than necessary while the engine is not running.
Can I fold an electric outside rearview mirror by hand?
In case it is an electric type outside rearview mirror, don’t fold it by hand. It could cause motor failure.
How do I fold the outside rearview mirror manually?
To fold the outside rearview mirror, grasp the housing of the mirror and then fold it toward the rear of the vehicle.
How do I adjust the instrument panel illumination?
The brightness of the instrument panel illumination is changed by pressing the illumination control button (“+” or “-”) when the ignition switch or Engine Start/Stop button is ON, or the taillights are turned on. If you hold the illumination control button (“+” or “-”), the brightness will be changed continuously. If the brightness reaches to the maximum or minimum level, an alarm will sound.
How do I change the LCD display modes?
The LCD display modes can be changed by using the control buttons on the steering wheel. (1) : MODE button for change the LCD MODES (2) / : MOVE scroll switch for select the items (3) OK : SET/RESET button for set the items or reset the items
What does the tachometer indicate?
The tachometer indicates the approximate number of engine revolutions per minute (rpm). Use the tachometer to select the correct shift points and to prevent lugging and/or over-revving the engine.
What does it mean if the engine coolant temperature gauge moves beyond the normal range toward the “H” position?
If the gauge pointer moves beyond the normal range area toward the “H” position, it indicates overheating that may damage the engine. Do not continue driving with an overheated engine.
What should I do if the engine overheats?
If your vehicle overheats, refer to “If the Engine Overheats” in chapter 7.
What is the red zone on the tachometer?
Do not operate the engine within the tachometer’s RED ZONE. This may cause severe engine damage.
When will the low fuel warning light illuminate?
The fuel gauge is supplemented by a low fuel warning light which will illuminate when the fuel tank is nearly empty.
What can cause the fuel gauge to fluctuate or the low fuel warning light to come on earlier than usual?
On inclines or curves, the fuel gauge pointer may fluctuate or the low fuel warning light may come on earlier than usual due to the movement of fuel in the tank.
When should I avoid filling the fuel tank?
Fuel display may not be accurate if you are filling in sloping places.
When should I not remove the radiator cap?
Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could cause severe burns. Wait until the engine is cool before adding coolant to the reservoir.
Why should I avoid driving with an extremely low fuel level?
Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire damaging the catalytic converter.
When should I stop to obtain additional fuel?
Stop and obtain additional fuel as soon as possible after the warning light comes on or when the gauge indicator comes close to the E level. Running out of fuel can expose vehicle occupants to danger.
What does the odometer indicate?
The odometer Indicates the total distance that the vehicle has been driven and should be used to determine when periodic maintenance should be performed.
What is the range of the odometer?
Odometer range: 0 ~ 999,999 miles or 1,599,999 km.
What does the outside temperature gauge indicate?
This gauge indicates the current outside air temperatures by 1°F (1°C).
What is the temperature range for the outside temperature gauge?
Temperature range: -40°F ~ 185°F (-40°C ~ 85°C).
Why might the outside temperature display not change immediately?
The outside temperature on the display may not change immediately like a general thermometer to prevent the driver from being distracted.
How do I change the temperature unit on the outside temperature gauge?
The temperature unit can be changed by using the “User Settings” mode of the LCD display.
What does the automatic transaxle shift indicator display?
This indicator displays which automatic transaxle shift lever is selected.
- Park : P
- Reverse : R
- Neutral : N
- Drive : D
- Sports Mode : 1, 2, 3, 4, 5, 6
What are the different LCD modes?
- Trip Computer: This mode displays driving information like the tripmeter, fuel economy, and so on.
- Turn By Turn (if equipped): This mode displays the state of the navigation.
- LDWS (if equipped): This mode displays the state of Lane Departure Warning System (LDWS).
- A/V (if equipped): This mode displays the state of the A/V system.
- Service: This mode informs of service interval (mileage or days) and pressure status of each tire.
- User Settings: On this mode, you can change settings of the doors, lamps, etc.
When should I edit settings from the User Settings mode?
For your safety, change the User Settings after parking the vehicle, applying the parking brake and moving the shift lever to P (Park).
What does the Service Mode Tire Pressure display?
This mode displays the pressure status of each tire.
How do I change the tire pressure unit?
You can change the tire pressure unit in “User settings” mode.
What does the Service Interval mode display?
It calculates and displays when you need a scheduled maintenance service (mileage or days).
When is the “Service in” message displayed?
If the remaining mileage or time reaches 900 mi. (1,500 km) or 30 days, “Service in” message is displayed for several seconds each time you set the ignition switch or Engine Start/Stop Button to the ON position.
How do I reset the service interval to the mileage and days inputted before?
To reset the service interval to the mileage and days you inputted before: Press the OK button (reset) for more than 1 second.
When is the “Service in OFF” message displayed?
If the service interval is not set “Service in OFF” message is displayed on the LCD display.
How do I activate the Service interval function?
If you want to activate Service interval function, set the service interval in the User setting mode.
What can cause the mileage and days to be incorrect?
If any of the following conditions occurs, the mileage and days may be incorrect:
- The battery cable is disconnected.
- The fuse switch is turned off.
- The battery is discharged.
What does the Master Warning Light indicate?
This warning light informs the driver of the following situations:
- Blind Spot Detection (BSD) malfunction (if equipped)
- Tire Pressure Monitoring System (TPMS) malfunction (if equipped)
- Autonomous Emergency Braking (AEB) malfunction (if equipped)
- Lamp malfunction and so on. The Master Warning Light illuminates when more than one of the above warning situations occur.
How do I access the User Settings mode?
In this mode, you can change settings of the doors, lights, etc.
When should I not adjust the User Setting?
Do not adjust the User Setting while driving. You may lose your steering control and cause severe personal injury or accidents.
What does the Rear Cross Traffic Alert do?
If this item is checked, the rear cross traffic alert function will be activated.
How do I activate or deactivate the AEB system?
To activate or deactivate the AEB system.
How do I choose the sensitivity of the FCW?
Choose the sensitivity of the FCW.
What does “Automatically Lock” setting do?
- Enable on Speed: All doors will be automatically locked when the vehicle speed reaches 9.3 mph (15km/h).
- Enable on Shift: All doors will be automatically locked if the automatic transmission is shifted from the P (Park) position to the R (Reverse) position.
What does the “Automatically Unlock” setting do?
- Disable: The auto door unlock operation will be canceled.
- Vehicle Off: All doors will be automatically unlocked when the ignition key is removed or when the ignition switch or the Engine Start/Stop button is set to the OFF position.
- On Shift to P: All doors will be automatically unlocked if the automatic transmission is shifted to the P (Park) position.
What does the “Two Press Unlock” setting do?
If this item is checked, the two press unlock will be activated.
What does the “Power Liftgate” setting do?
If this item is checked, the power liftgate function will be activated.
What does the “Smart Liftgate” setting do?
If this item is checked, the smart liftgate function will be activated. If the power liftgate function is not activated, you cannot activate this function.
How can I deactivate the one-touch turn signal function?
Off : The one touch turn signal function will be deactivated.
How do I activate the Head Lamp Delay function?
If this item is checked, the head lamp delay function will be activated.
How do I activate the Welcome Light function?
If this item is checked, the welcome light function will be activated.
How do I adjust the Park Assist System volume?
Adjust the Park Assist System volume. (Level 1~3).
How do I activate the Blind Spot Detection sound?
If this item is checked, the blind spot detection sound will be activated.
How do I activate the welcome sound?
If this item is checked, the welcome sound function will be activated.
How do I activate the service interval function?
On this mode, you can activate the service interval function with mileage (miles) and time (months).
How do I deactivate the service interval function?
Off : The service interval function will be deactivated.
How do I set the service interval?
On : You can set the service interval (mileage and months).
What does the “Steering Position” setting do?
If this item is checked, the warning function regarding the steering will be activated.
What does the “Wiper/Light Display” setting do?
If this item is checked, the LCD display shows a selected wiper or light mode if it is changed.
How do I set the average fuel economy to reset automatically?
If this item is checked, the average fuel economy will reset automatically when refueling or after ignition.
How do I choose the fuel economy unit?
Choose the fuel economy unit. (US gallon, UK gallon).
How do I choose the temperature unit?
Choose the temperature unit. (°C,°F).
How do I choose the tire pressure unit?
Choose the tire pressure unit. (psi, kPa, Bar).
What happens to some of the driving information stored in the trip computer if the battery is disconnected?
Some driving information stored in the trip computer (for example Average Vehicle Speed) resets if the battery is disconnected.
What is the range indicated by the range function in the trip computer?
The range is the estimated distance the vehicle can be driven with the remaining fuel. Distance range: 1 ~ 9,999 mi or 1 ~ 9,999 km.
What does the trip computer display if the estimated distance is below 1 mi (1 km)?
If the estimated distance is below 1mi. (1km), the trip computer will display “—” as range.
When might the range function not operate correctly?
If the vehicle is not on level ground or the battery power has been interrupted, the range function may not operate correctly.
How do I change the trip mode?
To change the trip mode, scroll the TRIP scroll switch ( / ) in the trip computer mode.
What does the trip computer display?
- Tripmeter
- Average Vehicle Speed
- Elapsed Time
- Range
- Average Fuel Economy
- Instant Fuel Economy
What can cause the range to differ from the actual driving distance?
The range may differ from the actual driving distance as it is an estimate of the available driving distance.
When might the trip computer not register additional fuel?
The trip computer may not register additional fuel if less than 1.6 gallons (6 liters) of fuel are added to the vehicle.
What can cause fuel economy and range to vary?
The fuel economy and range may vary significantly based on driving conditions, driving habits, and condition of the vehicle.
How is the average fuel economy calculated?
The average fuel economy is calculated by the total driving distance and fuel consumption since the last average fuel economy reset. Fuel economy range: 1 ~ 99.9 MPG or L/100km.
How do I reset average fuel economy manually?
To reset average fuel economy manually, press the OK button (reset) on the steering wheel for more than 1 second when the average fuel economy is displayed.
How do I set the average fuel economy to reset automatically when refueling?
To make the average fuel economy reset automatically whenever refueling, select the “Auto Reset” mode in User Setting menu of the LCD display.
What are the three conditions for when the vehicle will automatically reset the average fuel economy to default?
- OFF – You may set to default manually by using the trip switch reset button.
- When driving – The vehicle will automatically set to default once 4 hours pass after the Ignition is in OFF.
- When refueling – After refueling more than 6 liters and driving over 1km/h, the vehicle will reset to default automatically.
When is the average fuel economy not displayed?
The average fuel economy is not displayed for more accurate calculation if the vehicle does not drive more than 10 seconds or 0.03 miles (50 meters) since the ignition switch or Engine Start/Stop button is turned to ON.
What does the instant fuel economy display?
This mode displays the instant fuel economy during the last few seconds when the vehicle speed is more than 6.2 MPH (10 km/h). Fuel economy range: 0 ~ 50 MPG or 0 ~ 30 L/100km.
What does the tripmeter display?
The tripmeter is the total driving distance since the last tripmeter reset. Distance range: 0.0 ~ 9999.9 mi. or km.
How do I reset the tripmeter?
To reset the tripmeter, press the OK button (reset) on the steering wheel for more than 1 second when the tripmeter is displayed.
How is the average vehicle speed calculated?
The average vehicle speed is calculated by the total driving distance and driving time since the last average vehicle speed reset. Speed range : 0~160 MPH or 0~240 km/h.
How do I reset the average vehicle speed?
To reset the average vehicle speed, press the OK button (reset) on the steering wheel for more than 1 second when the average vehicle speed is displayed.
When is the average vehicle speed not displayed?
The average vehicle speed is not displayed if the driving distance is less than 0.03 miles (50 meters) or the driving time is less than 10 seconds since the ignition switch or Engine Start/Stop button is turned to ON.
Does the average vehicle speed stop when the vehicle is not in motion?
Even if the vehicle is not in motion, the average vehicle speed keeps going while the engine is running.
What does the elapsed time display?
The elapsed time is the total driving time since the last elapsed time reset. Time range (hh:mm): 00:00 ~ 99:59.
How do I reset the elapsed time?
To reset elapsed time, press the OK button (reset) on the steering wheel for more than 1 second when the elapsed time is displayed.
Does the elapsed time stop when the vehicle is not in motion?
Even if the vehicle is not in motion, the elapsed time keeps going while the engine is running.
What does the digital speedometer display?
This mode displays the current speed of the vehicle.
What is shown in the one time driving information mode?
This display shows trip distance (1), average fuel economy (2) and the estimated distance the vehicle can be driven with the remaining fuel (3). This information is displayed for a few seconds when you turn off the engine and then goes off automatically.
What happens if the estimated distance is below 1 mi (1 km) in the one time driving information mode?
If the estimated distance is below 1mi. (1km), the range (3) will display as “—”.
What will appear when the low fuel warning light illuminates in the cluster?
When low fuel warning light ( ) illuminates in the cluster, the refuel message will appear (4).
What does the Turn By Turn Mode display?
This mode displays the state of the navigation.
What does the LDWS Mode display?
This mode displays the state of the Lane Departure Warning System (LDWS).
What does the A/V Mode display?
This mode displays the state of the A/V system.
What does the “Shift to P position” warning message mean?
This warning message illuminates if you try to turn off the engine without the shift lever in P (Park) position. At this time, the Engine Start/Stop Button turns to the ACC position (If you press the Engine Start/Stop Button once more, it will turn to the ON position).
What does the “Low Key Battery” warning message mean?
This warning message illuminates if the battery of the smart key is discharged when the Engine Start/Stop Button changes to the OFF position.
What does the “Press start button while turn steering” warning message mean?
This warning message illuminates if the steering wheel does not unlock normally when the Engine Start/Stop Button is pressed. It means that you should press the Engine Start/Stop Button while turning the steering wheel right and left.
What does the “Steering wheel unlocked” warning message mean?
This warning message illuminates if the steering wheel does not lock when the Engine Start/Stop Button changes to the OFF position.
What does the “Check steering wheel lock system” warning message mean?
This warning message illuminates if the steering wheel does not lock normally when the Engine Start/Stop Button changes to the OFF position.
What does the “Press brake pedal to start engine” warning message mean?
This warning message illuminates if the Engine Start/Stop Button changes to the ACC position twice by pressing the button repeatedly without depressing the brake pedal. It means that you should depress the brake pedal to start the engine.
What does the “Key not in vehicle” warning message mean?
This warning message illuminates if the smart key is not in the vehicle when you press the Engine Start/Stop Button. It means that you should always have the smart key with you.
What does the “Key not detected” warning message mean?
This warning message illuminates if the smart key is not detected when you press the Engine Start/Stop Button.
What does the “Press start button again” warning message mean?
This warning message illuminates if you can not operate the Engine Start/Stop Button when there is a problem with the Engine Start/Stop Button system. It means that you could start the engine by pressing the Engine Start/ Stop Button once more. If the warning illuminates each time you press the Engine Start/Stop Button, have your vehicle inspected by an authorized Kia dealer.
What does the “Press start button with key” warning message mean?
This warning message illuminates if you press the Engine Start/Stop Button while the warning message “Key not detected” is illuminating. At this time, the immobilizer indicator light blinks.
What does the “Check fuse BRAKE SWITCH” warning message mean?
This warning message illuminates if the brake switch fuse is disconnected. It means that you should replace the fuse with a new one. If that is not possible, you can start the engine by pressing the Engine Start/Stop Button for 10 seconds in the ACC position.
What does the “Shift to P or N to start engine” warning message mean?
This warning message illuminates if you try to start the engine with the shift lever not in the P (Park) or N (Neutral) position. You can start the engine with the shift lever in the N (Neutral) position; however; we recommend that you start the engine with the shift lever in the P (Park) position for your safety.
What does the “Door/Hood/Liftgate Open” warning message mean?
It means that any door, hood, or liftgate is open.
What does the “Sunroof Open” warning message mean?
The warning message illuminates if you turn off the engine and then open the driver’s door when the sunroof is open.
When does the “Icy Road Warning Light” illuminate?
When the following conditions occur, the warning light (including Outside Temperature Gauge) blinks 5 times and then illuminates, and also warning chime sounds once: The temperature on the Outside Temperature Gauge is below approximately 40°F (4°C).
What should I do if the icy road warning light appears while driving?
If the icy road warning light appears while driving, you should drive more attentively and safely refraining from over-speeding, rapid acceleration, sudden braking or sharp turning, etc.
What does the “Align steering wheel” warning message mean?
This warning message illuminates if you start the engine when the steering wheel is turned to more than 90 degrees to the left or right. It means that you should turn the steering wheel and make the angle of the steering wheel be less than 30 degrees.
What does the “Low Washer Fluid” warning message mean?
This warning message illuminates on the service reminder mode if the washer fluid level in the reservoir is nearly empty. It means that you should refill the washer fluid.
What does the “Turn on FUSE SWITCH” warning message mean?
This warning message illuminates if the fuse switch on the fuse box is OFF. It means that you should turn the fuse switch on.
What does the “Low Fuel” warning message mean?
This warning message illuminates if the fuel tank is nearly empty.
- When the low fuel level warning light is illuminated.
- When the trip computer displays “— mile (or km)” as range. Add fuel as soon as possible.
What does the “Check headlight” warning message mean?
This warning message illuminates if there is a malfunction (burned-out bulb except LED lamp or circuit malfunction) with the headlamp. In this case, have your vehicle inspected by an authorized Kia dealer.
What should I do when replacing the bulb?
When replacing the bulb, use the same wattage bulb.
What happens if different wattage bulb is equipped with the vehicle?
If different wattage bulb is equipped with the vehicle, this warning message is not displayed.
What does the “Check AEB system” warning message mean?
This warning message illuminates if there is a malfunction with the Autonomous Emergency Braking (AEB) system. In this case, have your vehicle be inspected by an authorized Kia dealer.
What does the “Check Smart Phone Wireless Charger” warning message mean?
If a smart phone is still left on the wireless charging pad unattended, even when the ignition is in ACC OFF and the instrument panel’s one time driving information mode has finished, a warning message will light up on the instrument panel.
What does the “Check high beam assist system” warning message mean?
This warning message illuminates if there is a malfunction (burned-out bulb or circuit malfunction) with the headlamp. In this case, have your vehicle inspected by an authorized Kia dealer.
What does the Air Bag Warning Light indicate?
This warning light illuminates:
- Once you set the ignition switch or Engine Start/Stop Button to the ON position. – It illuminates for approximately 6 seconds and then goes off.
- When there is a malfunction with the SRS. In this case, have your vehicle inspected by an authorized Kia dealer.
What does the Seat Belt Warning Light indicate?
This warning light informs the driver that the seat belt is not fastened.
What does the Parking Brake & Brake Fluid Warning Light indicate?
This warning light illuminates:
- Once you set the ignition switch or Engine Start/Stop Button to the ON position. It illuminates for approximately 3 seconds. It remains on if the parking brake is applied.
- When the parking brake is applied.
- When the brake fluid level in the reservoir is low. If the warning light illuminates with the parking brake released, it indicates the brake fluid level in reservoir is low.
What should I do if the brake fluid level is low?
If the brake fluid level in the reservoir is low:
- Drive carefully to the nearest safe location and stop your vehicle.
- With the engine stopped, check the brake fluid level immediately and add fluid as required. Then check all brake components for fluid leaks. If any leaks in the brake system are still found, the warning light remains on, or the brakes do not operate properly, do not drive the vehicle. In this case, have your vehicle towed to an authorized Kia dealer and inspected.
What does the dual-diagonal braking system mean?
Your vehicle is equipped with dual-diagonal braking systems. This means you still have braking on two wheels even if one of the dual systems should fail. With only one of the dual systems working, more than normal pedal travel and greater pedal pressure are required to stop the vehicle. Also, the vehicle will not stop in as short a distance with only a portion of the brake system working.
What should I do if the brakes fail while driving?
If the brakes fail while you are driving, shift to a lower gear for additional engine braking and stop the vehicle as soon as it is safe to do so.
Is it safe to drive with the Parking Brake & Brake Fluid Warning Light ON?
Driving the vehicle with a warning light ON is dangerous. If the Parking Brake & Brake Fluid Warning Light illuminate with the parking brake released, it indicates that the brake fluid level is low. In this case, have your vehicle inspected by an authorized Kia dealer.
What does the Anti-lock Brake System (ABS) Warning Light indicate?
This warning light illuminates:
- Once you set the ignition switch or Engine Start/Stop Button to the ON position. It illuminates for approximately 3 seconds and then goes off.
- When there is a malfunction with the ABS (The normal braking system will still be operational without the assistance of the anti-lock brake system). In this case, have your vehicle inspected by an authorized Kia dealer.
What does it mean when both the ABS and the Parking Brake & Brake Fluid Warning Lights are on?
These two warning lights illuminate at the same time while driving: When the ABS and regular brake system may not work normally. In this case, have your vehicle inspected by an authorized Kia dealer.
What should I do if both the ABS and Parking Brake & Brake Fluid Warning Lights are on?
When both ABS and Parking Brake & Brake Fluid Warning Lights are on, the brake system will not work normally and you may experience an unexpected and dangerous situation during sudden braking thereby increasing the risk of a crash and injury. In this case, avoid high speed driving and abrupt braking. Have your vehicle inspected by an authorized Kia dealer as soon as possible.
What may not work if the ABS Warning Light is on or both ABS and Parking Brake & Brake Fluid Warning Lights are on?
When the ABS Warning Light is on or both ABS and Parking Brake & Brake Fluid Warning Lights are on, the speedometer, odometer, or trip-meter may not work. Also, the EPS Warning Light may illuminate and the steering effort may increase or decrease. In this case, have your vehicle inspected by an authorized Kia dealer as soon as possible.
What does the Electronic Power Steering (EPS) Warning Light indicate?
This warning light illuminates:
- Once you set the ignition switch or Engine Start/Stop Button to the ON position. It remains on until the engine is started.
- When there is a malfunction with the EPS. In this case, have your vehicle inspected by an authorized Kia dealer.
When does the parking assist system not operate normally?
The parking assist system may not operate normally when:
- Moisture is frozen to the sensor. (It will operate normally when moisture melts.)
- The sensor is covered with foreign matter, such as snow or water, or the sensor cover is blocked. (It will operate normally when the material is removed or the sensor is no longer blocked.)
- The sensor is stained with foreign matter such as snow or water. (Sensing range will return to normal when removed.)
- The parking assist button is off.
When is there a possibility of the parking assist system malfunctioning?
There is a possibility of the parking assist system malfunctioning when:
- Driving on uneven road surfaces such as unpaved roads, gravel, bumps, or gradient.
- Objects generating excessive noise such as vehicle horns, loud motorcycle engines, or truck air brakes can interfere with the sensor.
- Heavy rain or water spray.
- Wireless transmitters or mobile phones present near the sensor.
- The sensor is covered with snow.
When may the detecting range of the parking assist system decrease?
The detecting range may decrease when:
- Outside air temperature is extremely hot or cold.
- Undetectable objects are smaller than 1m and narrower than 14cm in diameter.
What objects may not be recognized by the parking assist sensor?
The following objects may not be recognized by the sensor:
- Sharp or slim objects such as ropes, chains or small poles.
- Objects, which tend to absorb sensor frequency such as clothes, spongy material or snow.
What are some limitations of the parking assist system regarding audible warnings?
The warning may not sound sequentially depending on the speed and shapes of the objects detected.
What can cause the parking assist system to malfunction?
The parking assist system may malfunction if the vehicle bumper height or sensor installation has been modified. Any non-factory installed equipment or accessories may also interfere with the sensor performance.
What is the minimum distance that the parking assist sensor may not recognize an object?
The sensor may not recognize objects less than 30 cm from the sensor, or it may sense an incorrect distance.
What should you do if the parking sensor is frozen or stained?
When the sensor is frozen or stained with snow or water, the sensor may be inoperative until the stains are removed using a soft cloth.
What should you avoid doing to the parking sensor?
Do not push, scratch or strike the sensor with any hard objects that could damage the surface of the sensor. Sensor damage could occur.
What indicates a malfunction in the rear parking assist system?
When you shift the gear to the R (Reverse) position and if one or more of the below occurs you may have a malfunction in the rear parking assist system:
- You don’t hear an audible warning sound or if the buzzer sounds intermittently.
What does the vehicle warranty not cover related to the parking assist system?
The new vehicle warranty does not cover any accidents or damage to the vehicle or injuries to its occupants related to a parking assist system.
What should you always do before moving the vehicle?
Always perform a visual inspection to make sure the vehicle is clear of all obstructions before moving the vehicle in any direction.
When does the rearview camera activate?
The rearview camera will activate with the ignition switch ON and the shift lever in the R (Reverse) position.
How can the rearview camera be turned off?
The rearview camera may be turned off by pressing the ON/OFF button when the rearview camera is activated.
How do you turn the camera back on?
To turn the camera on again, press the ON/OFF button again when the ignition switch is on and the shift lever is in R (Reverse). Also, the camera will turn on automatically whenever the ignition switch is turned off and on again.
What should a driver always check before and while backing up?
It is the responsibility of the driver to always check the inside/outside rearview mirrors and the area behind the vehicle before and while backing up because there is a dead zone that can’t be seen by the camera.
What should you always keep clean on the rearview camera?
Always keep the camera lens clean. If lens is covered with foreign matter, the camera may not operate normally.
What should you never rely solely on when backing up?
Never rely solely on the rear view camera when backing.
What methods should you use when backing up besides the rearview camera?
You must always use methods of viewing the area behind you including looking over both shoulders as well as continuously checking all three rear view mirrors.
What is the purpose of the battery saver function?
The purpose of this feature is to prevent the battery from being discharged if the lights are left in the ON position.
When does the system automatically shut off the parking lights?
The system automatically shuts off the parking lights 30 seconds after the ignition key is removed and the driver’s door is opened and closed.
How can you keep the parking lights on when the ignition key is removed?
To keep the parking lights on when the ignition key is removed, perform the following: 1) Open the driver-side door. 2) Turn the parking lights OFF and ON again using the light switch on the steering column.
When does the Daytime Running Lights (DRL) system turn OFF?
The DRL system turns OFF when:
- The headlight switch is ON.
- The engine is OFF.
- The front fog light is ON.
- Engaging the Parking Brake.
What lights turn on when the light switch is in the parking light position?
When the light switch is in the parking light position, the tail, license and instrument panel lights will turn ON.
What lights turn on when the light switch is in the headlight position?
When the light switch is in the headlight position, the head, tail, license lights will turn ON.
What position must the ignition switch be in to turn on the headlights?
The ignition switch must be in the ON position to turn on the headlights.
When do the taillights and headlights turn on automatically when the light switch is in the AUTO position?
When the light switch is in the AUTO light position, the taillights and headlights will turn ON or OFF automatically depending on the amount of light outside the vehicle.
What happens when the light switch is in the AUTO position, the wiper is turned on, and the head lamp is turned on?
When the light switch is positioned at an auto light position, at first, the wiper will turn on and then, after 5 seconds the head lamp will turn on automatically. If the head lamp has been turned on due to this function of the vehicle, the head lamp will turn off 60 seconds after the wiper has been turned off.
How do you turn on the high beam headlamp?
To turn on the high beam headlamp, push the lever away from you. The lever will return to its original position.
What indicates that the headlight high beams are switched on?
The high beam indicator will light when the headlight high beams are switched on.
How do you turn off the high beam headlamp?
To turn off the high beam headlamp, pull the lever to you when the high beam is on. The lever will return to its original position.
How do you flash the headlights?
To flash the headlights, pull the lever towards you. It will return to the normal (low beam) position when released. The headlight switch does not need to be on to use this flashing feature.
When should you not use high beams?
Do not use high beam when there are other vehicles. Using high beam could obstruct the other driver’s vision.
What does the High Beam Assist system do?
The High Beam Assist is a system that automatically adjusts the headlamp range (switches between high beam and low beam) according to the brightness of other vehicles and road conditions.
What are the operating conditions for High Beam Assist?
The operating conditions are:
- Place the light switch in the AUTO position.
- Turn on the high beam by pushing the lever away from you. The High Beam Assist ( ) indicator will illuminate.
- The High Beam Assist will turn on when vehicle speed is above 25mph (40kph).
What happens if the lever is pushed away when the High Beam Assist is operating?
If the lever is pushed away when the High Beam Assist is operating, the High Beam Assist will turn off and the high beam will be on continuously. The High Beam Assist ( ) indicator will turn off.
What happens if the lever is pulled towards you when the High Beam Assist is operating?
If the lever is pulled towards you when the High Beam Assist is operating, the High Beam Assist will turn off.
What happens if the light switch is placed in the headlamp position when using the High Beam Assist?
If the light switch is placed to the headlamp position, the High Beam Assist will turn off and the low beam will be on continuously.
Under what conditions does the high beam switch to low beam?
The high beam switches to low beam in the below conditions:
- When the High Beam Assist is off.
- When the light switch is not in the AUTO position.
- When the headlamp is detected from the on-coming vehicle.
- When the tail lamp is detected from the front vehicle.
- When the surrounding is bright enough high beams are not needed.
- When streetlights or other lights are detected.
- When vehicle speed is below 15mph (24kph).
- When headlamp / taillamp of bicycle/motorcycle is detected.
When may the High Beam Assist system not operate normally?
The system may not operate normally in the below conditions:
- When the light from the on-coming or front vehicle is not detected because of lamp damage, hidden from sight, etc.
- When the lamp of the on-coming or front vehicle is covered with dust, snow or water.
- When the light from the on-coming or front vehicle is not detected because of exhaust fumes, smoke, fog, snow, etc.
- When the front window is covered with foreign matters such as ice, dust, fog, or is damaged.
- When there is a similar shape lamp with the front vehicle’s lamps.
- When it is hard to see because of fog, heavy rain or snow.
- When the headlamp is not repaired or replaced at an authorized dealer.
- When headlamp aiming is not properly adjusted.
- When driving on a narrow curved road or rough road.
- When driving downhill or uphill.
- When only part of the vehicle in front is visible on a crossroad or curved road.
- When there is a traffic light, reflecting sign, flashing sign or mirror.
- When the road conditions are bad such as being wet or covered with snow.
- When the front vehicle’s headlamps are off but the fog lamps on.
- When a vehicle suddenly appears from a curve.
- When the vehicle is tilted from a flat tire or being towed.
- When the LDWS (lane departure warning system) warning light illuminates. (if equipped).
What should you avoid placing on the windshield to ensure proper operation of the High Beam Assist system?
Do not place any accessories, stickers or tint the windshield.
What should you be careful not to do regarding water and the High Beam Assist unit?
Be careful that water doesn’t get into the High Beam Assist unit.
What should you not place on the dashboard, as it may interfere with the High Beam Assist system?
Do not place objects on the dashboard that reflect light such as mirrors, white paper, etc. The system may malfunction if sunlight is reflected.
What should you do if the Smart High Beam system does not work properly?
When the system does not operate normally, manually change between the high beam and low beam.
When do the turn signals function?
The ignition switch must be on for the turn signals to function.
How do you activate the turn signals?
To turn on the turn signals, move the lever up or down (A). The green arrow indicators on the instrument panel indicate which turn signal is operating.
How do the turn signals cancel after a turn is completed?
They will self-cancel after a turn is completed.
What should you do if the turn signal indicator continues to flash after a turn?
If the indicator continues to flash after a turn, manually return the lever to the OFF position.
How do you signal a lane change?
To signal a lane change, move the turn signal lever slightly and hold it in position (B). The lever will return to the OFF position when released.
What does it mean if an indicator stays on and does not flash or if it flashes abnormally?
If an indicator stays on and does not flash or if it flashes abnormally, one of the turn signal bulbs may be burned out and will require replacement.
What does it mean if an indicator flash is abnormally quick or slow?
If an indicator flash is abnormally quick or slow, a bulb may be burned out or have a poor electrical connection in the circuit.
When should fog lights be used?
Fog lights are used to provide improved visibility when visibility is poor due to fog, rain or snow, etc.
How do you turn on the fog lights?
The fog lights will turn on when the fog light switch (1) is turned to the on position after the headlight is turned on.
How do you turn off the fog lights?
To turn off the fog lights, turn the fog light switch (1) to the OFF position.
When should you only use the fog lights?
Only use the fog lights when visibility is poor.
What does the “Check headlight” warning message indicate?
This warning message illuminates if there is a malfunction (burned-out bulb except LED lamp or circuit malfunction) with the headlamp.
What should you do if the “Check headlight” warning message is displayed?
In this case, have your vehicle inspected by an authorized Kia dealer.
What should you do when replacing a bulb?
When replacing the bulb, use the same wattage bulb.
What happens if a different wattage bulb is equipped with the vehicle?
If a different wattage bulb is equipped with the vehicle, this warning message is not displayed.
What does the Adaptive Front Lighting System (AFLS) do?
The adaptive front lighting system uses the steering angle and vehicle speed, to keep your field of vision wide by swiveling and leveling the headlamp.
How do you operate the Adaptive Front Lighting System (AFLS)?
Change the switch to the AUTO position when the engine is running. The adaptive front lighting system will operate when the headlamp is ON.
How do you turn off the AFLS?
To turn off the AFLS, change the switch to other positions.
What happens after turning off the AFLS?
After turning the AFLS off, headlamp swiveling no longer occurs, but leveling operates continuously.
What does the AFLS malfunction indicator mean?
If the AFLS malfunction indicator comes on, the AFLS is not working properly.
What should you do if the AFLS malfunction indicator is displayed?
Drive to the nearest safe location and restart the engine. If the indicator continuously remains on, have the system checked by an authorized Kia dealer.
What are the different settings for the front wiper speed control?
The front wiper speed control settings are:
- MIST – Single wipe
- OFF – Off
- INT – Intermittent wipe
- LO – Low wiper speed
- HI – High wiper speed.
How do you adjust the intermittent control wipe time?
Use the intermittent control wipe time adjustment setting.
How do you use the front wash with brief wipes function?
Use the wash with brief wipes (front) setting.
What are the settings for the rear wiper/washer control?
The settings are:
- HI – Continuous wipe
- LO – Intermittent wipe
- OFF – Off.
How do you use the rear wash with brief wipes function?
Use the wash with brief wipes (rear) setting.
How do you operate the windshield wipers in the MIST position?
For a single wiping cycle, move the lever to this (MIST) position and release it. The wipers will operate continuously if the lever is held in this position.
When should you use the INT setting for the windshield wipers?
Use this mode in light rain or mist.
How do you vary the speed setting when using the INT setting on the windshield wipers?
To vary the speed setting, turn the speed control knob.
What are the LO and HI settings for the windshield wipers?
LO is normal wiper speed and HI is fast wiper speed.
What should you do if there is heavy accumulation of snow or ice on the windshield before using the windshield wipers?
Defrost the windshield for about 10 minutes, or until the snow and/or ice is removed before using the windshield wipers to ensure proper operation.
What can happen if you do not remove snow and/or ice before using the wipers?
If you do not remove the snow and/or ice before using the wiper and washer, it may damage the wiper and washer system.
How do you use the front windshield washers?
In the OFF position, pull the lever gently toward you to spray washer fluid on the windshield and to run the wipers 1-3 cycles.
When should you use the front windshield washer function?
Use this function when the windshield is dirty.
What happens if the washer does not work?
If the washer does not work, check the washer fluid level.
Where is the washer fluid reservoir located?
The reservoir filler neck is located in the front of the engine compartment on the passenger side.
What can happen if you operate the washer when the fluid reservoir is empty?
To prevent possible damage to the washer pump, do not operate the washer when the fluid reservoir is empty.
Where is the rear window wiper and washer switch located?
The rear window wiper and washer switch is located at the end of the wiper and washer switch lever.
How do you operate the rear wiper and washer?
Turn the switch to the desired position to operate the rear wiper and washer.
When should you not use the washer in freezing temperatures?
Do not use the washer in freezing temperatures without first warming the windshield with the defrosters; the washer solution could freeze on the windshield and obscure your vision.
What should you not do when the windshield is dry?
To prevent possible damage to the wipers or windshield, do not operate the wipers when the windshield is dry.
What should you not use on or near the wiper blades?
To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.
What should you not do to the wiper arms?
To prevent damage to the wiper arms and other components, do not attempt to move the wipers manually.
How do you use the rear washer fluid?
Push the lever away from you to spray rear washer fluid and to run the rear wipers 1~3 cycles. The spray and wiper operation will continue until you release the lever.
What should you avoid doing to prevent battery discharge related to interior lights?
Do not use the interior lights for extended periods when the engine is not running. It may cause battery discharge.
How long do interior lights automatically turn off after the ignition switch is turned off?
The interior lights automatically turn off approximately 20 minutes after the ignition switch is turned off, if the lights are in the ON position.
How long do interior lights automatically turn off if the vehicle is equipped with the theft alarm system?
If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 5 seconds after the system is in armed stage.
When should you not use interior lights?
Do not use the interior lights when driving in the dark. Accidents could happen because the view may be obscured by interior lights.
How do you turn the map lamp on and off?
Press the lens (1) to turn ON the map lamp. To turn the map lamp OFF press the lens (1) again.
What does the DOOR mode for the map lamp and room lamp do?
The map lamp and room lamp come on when a door is opened. The lamps go out after approximately 30 seconds.
- The map lamp and room lamp come on for approximately 30 seconds when doors are unlocked with a transmitter or smart key as long as the doors are not opened.
When do the map lamp and room lamp stay on for 20 minutes?
The map lamp and room lamp will stay on for approximately 20 minutes if a door is opened with the ignition switch in the ACC or LOCK/OFF position.
When do the map lamp and room lamp stay on continuously?
The map lamp and room lamp will stay on continuously if the door is opened with the ignition switch in the ON position.
When do the map lamp and room lamp go out immediately?
The map lamp and room lamp will go out immediately if the ignition switch is changed to the ON position or all doors are locked.
How do you turn off the DOOR mode?
To turn off the DOOR mode, press the DOOR button (2) once again (not pressed).
What should be avoided regarding the DOOR mode and ROOM mode?
The DOOR mode and ROOM mode can not be selected at the same time.
How do you turn the front and rear room lamps on using type A?
Press this switch to turn the front and rear room lamps on.
How do you turn the front and rear room lamps off using type A?
Press this switch to turn the front and rear room lamps off.
How do you turn the front and rear room lamps on and off using type B?
Press this switch to turn the front and rear room lamps on and off.
When does the liftgate room lamp come on?
The liftgate room lamp comes on when the liftgate is opened.
What should you do to prevent unnecessary charging system drain related to the liftgate lamp?
To prevent unnecessary charging system drain, close the liftgate lid securely after using the liftgate.
How do you turn the vanity mirror lamp on and off?
Push the switch to turn the light on or off.
When should you always have the vanity mirror lamp switch in the off position?
Always have the switch in the off position when the vanity mirror lamp is not in use. If the sunvisor is closed without the lamp off, it may discharge the battery or damage the sunvisor.
When does the glove box lamp come on?
The glove box lamp comes on when the glove box is opened.
What should you do to prevent unnecessary battery drain related to the glove box lamp?
To prevent unnecessary battery drain, close the glove box securely after using the glove box.
How long do the headlights (and/or taillights) remain on after the ignition key is removed or turned to the ACC or LOCK position for the headlight escort function?
The headlights (and/or taillights) remain on for approximately 5 minutes after the ignition key is removed or turned to the ACC or LOCK position.
How long do the headlights remain on after the driver’s door is opened and closed for the headlight escort function?
If the driver’s door is opened and closed, the headlights are turned off after 15 seconds.
How can the headlights be turned off for the headlight escort function?
The headlights can be turned off by pressing the lock button on the transmitter or smart key twice or turning off the light switch from the headlight or Auto light position.
When will the room lamp come on for 30 seconds if the interior light switch is in the DOOR position and all doors are locked and closed for the Welcome System?
The room lamp will come on for 30 seconds if any of the below is performed.
- Without smart key system: When the door unlock button is pressed on the transmitter.
- With the smart key system:
- When the door unlock button is pressed on the smart key.
- When the button of the outside door handle is pressed.
How can the lamps be turned off immediately for the Welcome System?
At this time, if you press the door lock button, the lamps will turn off immediately.
When will the pocket lamp come on for 15 seconds when all doors are locked and closed for the Welcome System?
The pocket lamp will come on for 15 seconds if any of the below is performed.
- With the smart key system:
- When the door unlock button is pressed on the smart key.
- When the button of the outside door handle is pressed.
How can the pocket lamps be turned off immediately?
At this time, if you press the door lock button, the lamps will turn off immediately.
How do you activate the rear window defroster?
To activate the rear window defroster, press the rear window defroster button located in the center facia switch panel.
What indicates that the rear window defroster is on?
The indicator on the rear window defroster button illuminates when the defroster is ON.
What should you do before operating the rear defroster if there is heavy accumulation of snow on the rear window?
If there is heavy accumulation of snow on the rear window, brush it off before operating the rear defroster.
When does the rear window defroster automatically turn off?
The rear window defroster automatically turns off after approximately 20 minutes or when the ignition switch is turned off.
How do you turn off the rear window defroster?
To turn off the defroster, press the rear window defroster button again.
When does the wiper deicer operate?
If your vehicle is equipped with the wiper deicer, it will operate at the same time you turn on the rear window defroster.
What should you never use to clean the rear window to prevent damage to the conductors?
To prevent damage to the conductors bonded to the inside surface of the rear window, never use sharp instruments or window cleaners containing abrasives to clean the window.
What could operating the blower when the ignition switch is in the ON position cause?
Operating the blower when the ignition switch is in the ON position could cause the battery to discharge. Operate the blower when the engine is running.
How do you operate the heating and air conditioning system?
To operate the heating and air conditioning system:
- Start the engine.
- Set the mode to the desired position.
- Set the temperature control to the desired position.
- Set the air intake control to the outside (fresh) air position (if equipped).
- Set the fan speed control to the desired speed.
- If air conditioning is desired, turn the air conditioning system (if equipped) on.
What does the mode selection button control?
The mode selection button controls the direction of the air flow through the ventilation system. Air can be directed to the floor, dashboard outlets, or windshield.
What are the five symbols used to represent the different modes?
Five symbols are used to represent MAX A/C, Face, Bi-Level, Floor, Floor-Defrost and Defrost air position.
What does the MAX A/C mode do?
The MAX A/C mode is used to cool the inside of the vehicle faster.
What does the Face-Level mode do?
Air flow is directed toward the upper body and face.
What does the Bi-Level mode do?
Air flow is directed towards the face and the floor.
What does the Floor-Level mode do?
Most of the air flow is directed to the floor, with a small amount of the air being directed to the windshield and side window defrosters.
What does the Floor/Defrost-Level mode do?
Most of the air flow is directed to the floor and the windshield with a small amount directed to the side window defrosters.
What does the Defrost-Level mode do?
Most of the air flow is directed to the windshield with a small amount of air directed to the side window defrosters.
How is the airflow of the 2nd row outlet vents controlled?
The air flow of the 2nd row outlet vents is controlled by the front climate control system and delivered through the inside air duct of the floor.
Why may the air flow of the 2nd row outlet vents be weaker?
The air flow of the 2nd row outlet vents may be weaker than the instrument panel vents for the long air duct.
What does the MAX A/C selection do?
The MAX A/C mode is used to cool the inside of the vehicle faster. Air flow is directed toward the upper body and face. In this mode, the air conditioning and the recirculated air position will be selected automatically.
How do you open or close the instrument panel vents?
The outlet vents can be opened or closed separately using the thumb-wheel (if equipped).
How do you adjust the direction of air delivery from the instrument panel vents?
You can adjust the direction of air delivery from these vents using the vent control lever.
How do you change the temperature of air flow for the driver or passenger?
To change the air temperature, turn the knob to the right position for warmer air or left position for cooler air.
What does the air intake control do?
The air intake control is used to select the outside (fresh) air position or recirculated air position.
How do you change the air intake control position?
To change the air intake control position, press the control button.
What happens when the recirculated air position is selected?
With the recirculated air position selected, air from the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.
What happens when the outside (fresh) air position is selected?
With the outside (fresh) air position selected, air enters the vehicle from outside and is heated or cooled according to the function selected.
What can prolonged operation of the heater in the recirculated air position cause?
Prolonged operation of the heater in the recirculated air position (without air conditioning selected) may cause fogging of the windshield and side windows and the air within the passenger compartment may become stale.
What can prolonged use of the air conditioning with the recirculated air position cause?
In addition, prolonged use of the air conditioning with the recirculated air position selected will result in excessively dry air in the passenger compartment.
What happens if the sunroof opens while the heater or Air Conditioning system operates?
If the sunroof opens while the heater or Air Conditioning system operates, the outside (fresh) air will be selected automatically for ventilating the car.
How do I use the cup holders?
Cups or small beverage cans may be placed in the cup holders.
How do I use the bottle holders?
Bottles may be placed in the bottle holder. Only bottles should be placed in the holder labeled “Bottles Only”.
What should I be aware of when placing hot liquids in the cup holder?
Do not place uncovered cups with hot liquid in the cup holder while the vehicle is in motion. If the hot liquid spills, you may burn yourself, and such a burn to the driver could lead to loss of control of the vehicle.
What should I be aware of regarding sealed drinks?
Keep your drinks sealed while driving to prevent spilling your drink. If liquid spills, it may get into the vehicle’s electrical/electronic system and damage electrical/electronic parts.
How should I clean spilled liquids from the cup holders?
When cleaning spilled liquids, do not use heat to dry the cup holders. This may damage the cup holder.
How do I use the seat warmer?
With the ignition switch in the ON position, push either of the switches to warm the driver’s seat or the front passenger’s seat.
What should I do when the seat warmer is not needed?
During mild weather or under conditions where the operation of the seat warmer is not needed, keep the switches in the “OFF” position.
How does the temperature setting of the seat change when using the seat warmer?
Each time you press the switch, the temperature setting of the seat will change as follows: OFF→HIGH→MIDDLE→LOW→ OFF.
What is the default position of the seat warmer?
The seat warmer defaults to the OFF position whenever the ignition switch is turned on.
Does the seat warmer have an automatic heating system?
With the seat warmer switch in the ON position, the heating system in the seat turns off or on automatically depending on the seat temperature.
What are the warnings regarding seat warmer burns?
The seat warmer may cause burns, even at low temperatures, if used over a long period of time. Never allow passengers who may not be able to take care of themselves to be exposed to the risk of seat heater burns. These include:
- Infants, children, elderly or disabled persons, or hospital outpatients
- Persons with sensitive skin or those that burn easily
- Fatigued individuals
- Intoxicated individuals
- Individuals taking medication that can cause drowsiness or sleepiness (sleeping pills, cold tablets, etc.)
How do I use the air ventilation seat?
If you want to ventilate your seat cushion, press the switch (blue color).
How does the airflow change with the air ventilation seat?
Each time you press the button, the airflow will change as follows: OFF→HIGH→MIDDLE→LOW.
What is the default position of the air ventilation seat?
The seat warmer (with air ventilation) defaults to the OFF position whenever the ignition switch is turned on.
What should I not use to clean the air ventilation seats?
When cleaning the seats, do not use an organic solvent such as paint thinner, benzene, alcohol and gasoline. Doing so may damage the air ventilation seat.
What should I be careful of when placing items on the air ventilation seat?
Do not place heavy or sharp objects on the seat. Those things may damage the air ventilation seat.
What should I do if I spill liquid on the air ventilation seat?
Be careful not to spill liquid such as water or beverages on the seat. If you spill some liquid, wipe the seat with a dry towel. Before using the air ventilation seat, dry the seat completely.
How do I use the sunvisor?
To use the sunvisor, pull it downward. To use the sunvisor for the side window, pull it downward, unsnap it from the bracket and swing it to the side. To use the vanity mirror, pull down the visor and slide the mirror cover. Adjust the sunvisor extension forward or backward. The ticket holder is provided for holding a tollgate ticket.
What should I be aware of when using the vanity mirror lamp?
If you use the vanity mirror lamp, turn off the lamp before returning the sunvisor to its original position, otherwise it could result in battery discharge and possible sunvisor damage.
How is the power outlet designed to be used?
The power outlet is designed to provide power for mobile telephones or other devices designed to operate with vehicle electrical systems. The devices should draw less than 10 amps with the engine running.
When should I use the power outlet?
Use the power outlet only when the engine is running and remove the accessory plug after use. Using the accessory plug for prolonged periods of time with the engine off could cause the battery to discharge.
What kind of accessories should be used with the power outlet?
Only use 12V electric accessories which are less than 10A in electric capacity.
What should I do when using the power outlet?
Adjust the air-conditioner or heater to the lowest operating level when using the power outlet. Close the cover when not in use.
What should I be aware of regarding electronic devices used with the power outlet?
Some electronic devices can cause electronic interference when plugged into a vehicle’s power outlet. These devices may cause excessive audio static and malfunctions in other electronic systems or devices used in your vehicle.
What should I do to ensure good contact when plugging into the power outlet?
Push the plug in as far as it will go. If good contact is not made, the plug may overheat and the fuse may open.
What should I be aware of regarding battery equipped electronic devices with the power outlet?
Plug in battery equipped electronic devices with reverse current protection. The current from the battery may flow into the vehicle’s electrical/electronic system and cause system malfunction.
What kind of chargers should I use to charge my devices?
Do not use aftermarket chargers to charge devices. Only use device certified cables to charge.
How does the USB charger work?
The USB charger is designed to recharge batteries of small size electrical devices using a USB cable. The electrical devices can be recharged when the Engine Start/Stop button is in ACC/ON/START position. The battery charging state may be monitored on the electrical device. Disconnect the USB cable from the USB port after use.
What should I be aware of when using the USB charger?
Some devices are not supported for fast charging but will be charged with normal speed. Use the USB charger when the engine is running to prevent battery discharge. Only devices that fit the USB port can be used. The USB charger can be used only for battery charging purposes. Battery chargers cannot be charged.
What are the warnings regarding the power outlet and electric shock?
Do not put a finger or a foreign element (pen, etc.) into a power outlet and do not touch with a wet hand. You may receive an electric shock.
How does the wireless smart phone charging system work?
A wireless smart phone charging system is located in front of the center console. Firmly close all doors, and turn the ignition to ACC or IGN ON. To start wireless charging, place the smart phone equipped with wireless charging function on the wireless charging pad. For best wireless charging results, place the smart phone on the center of the charging pad. The wireless charging system is designed for one smart phone equipped with QI per single usage only.
How can I check if my smart phone supports wireless charging?
Please refer to the smart phone accessory cover or the smart phone manufacturer homepage to check whether your smart phone supports QI function.
What should I do before using the wireless smart phone charger?
Remove any object on the smart phone charging pad including the smart key. If there is any foreign object on the pad other than a smart phone, the wireless charging function may not operate properly. Place the smart phone on the center of the wireless charging pad.
How can I tell if the wireless charging is working?
The indicator light will change to orange once the wireless charging begins. After the charging is complete, the orange light will change to green.
Can I turn off the wireless charging function?
You can choose to turn the wireless charging function to either ON or OFF by selecting the USM on the instrument cluster.
What should I do if the wireless charging does not work?
If the wireless charging does not work, gently move your smart phone around the pad until the charging indicator light turns orange. Depending on the smart phone, the charging indicator light may not turn green even after the charging is complete.
What happens if the wireless charging is not functioning properly?
If the wireless charging is not functioning properly, the orange light will blink and flash for ten seconds then turn off. In such cases, remove the smart phone from the pad and replace it on the pad again, or double check the charging status.
What happens if I leave my smart phone on the charging pad when the vehicle ignition is in OFF?
If you leave the smart phone on the charging pad when the vehicle ignition is in OFF, the vehicle will alert you through warning messages and sound (applicable for vehicles with voice guidance (function) after the ‘Good bye’function on the instrument cluster ends).
What are the warnings regarding distracted driving?
Driving while distracted can result in a loss of vehicle control that may lead to an accident, severe personal injury, and death. The driver’s primary responsibility is in the safe and legal operation of a vehicle, and use of any handheld devices, other equipment, or vehicle systems which take the driver’s eyes, attention and focus away from the safe operation of a vehicle or which are not permissible by law should never be used during operation of the vehicle.
What should I be aware of regarding metal and the wireless charging system?
If any metallic object such as coins is located between the wireless charging system and the smart phone, the charging may be disrupted. Also, the metallic object may heat up and potentially damage the charging system. If there is any metallic object between the smart phone and the charging pad, immediately remove the smart phone. Remove the metallic object after it has cooled down.
What happens when the interior temperature of the wireless charging system rises above a set temperature?
When the interior temperature of the wireless charging system rises above a set temperature, the wireless charging will cease to function. After the interior temperature drops below the threshold, the wireless charging function will resume.
What should I be aware of regarding heavy accessory covers and wireless charging?
The wireless charging may not function properly when there is a heavy accessory cover on the smart phone.
What should I be aware of regarding the wireless smart key search function and wireless charging?
The wireless charging will stop when using the wireless smart key search function to prevent radio wave disruption.
What happens to wireless charging when the smart key is moved out of the vehicle?
The wireless charging will stop when the smart key is moved out of the vehicle with the ignition in ON.
What happens to wireless charging when a door is opened?
The wireless charging will stop when any of the doors is opened (applicable for vehicles equipped with smart keys).
What happens to wireless charging when the vehicle is turned OFF?
The wireless charging will stop when the vehicle is turned OFF.
What happens to wireless charging when the smart phone is not in complete contact with the wireless charging pad?
The wireless charging will stop when the smart phone is not in complete contact with the wireless charging pad.
What types of items might be damaged during wireless charging?
Items equipped with magnetic components such as credit cards, telephone cards, bank books, any transportation ticket and such may become damaged during wireless charging.
Where should the smart phone be placed on the charging pad for best results?
Place the smart phone on the center of the charge pad for best results. The smart phone may not charge when placed near the rim of the charging pad. When the smart phone does get charged, it may heat up excessively.
What should I do if I have a smart phone without a built-in wireless charging system?
For smart phones without built-in wireless charging system, an appropriate accessory has to be equipped.
What does it mean if some smart phones display messages about weak current?
Smart phones of some manufacturers may display messages on weak current. This is due to the particular characteristic of the smart phone and does not imply a malfunction on wireless charging function.
How do I use the clothes hanger?
To use the hanger, pull down the upper portion of hanger.
What should I be careful about when hanging clothes?
Do not hang heavy clothes, since those may damage the hook.
How do I use the floor mat anchor(s)?
When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor(s) in your vehicle. This keeps the floor mat from sliding forward.
What should I be aware of regarding aftermarket floor mats?
Do not install aftermarket floor mats that are not capable of being securely attached to the vehicle’s floor mat anchors. Unsecured floor mats can interfere with pedal operation.
What must be observed when installing ANY floor mat to the vehicle?
- Ensure that the floor mats are securely attached to the vehicle’s floor mat anchor(s) before driving the vehicle.
- Do not use ANY floor mat that cannot be firmly attached to the vehicle’s floor mat anchors.
- Do not stack floor mats on top of one another (e.g. all-weather rubber mat on top of a carpeted floor mat). Only a single floor mat should be installed in each position.
What does Kia recommend regarding the floor mat?
Kia recommends that only the Kia floor mat designed for use in your vehicle be installed.
How do I use the luggage net holder?
To keep items from shifting in the cargo area, you can use the holders located in the cargo area to attach the luggage net. If necessary, we recommend that you contact an authorized Kia dealer.
What should I be careful of when carrying fragile or bulky objects in the luggage compartment?
To prevent damage to the vehicle, care should be taken when carrying fragile or bulky objects in the luggage compartment.
What are the warnings regarding the luggage net?
Always keep your face and body out of the luggage net recoil path and avoid using the luggage net when the straps have visible signs of wear or damage. The luggage net can snap and cause injuries.
How do I use the cargo security screen?
Use the cargo security screen to hide items stored in the cargo area. To use the cargo security screen, pull the handle backward and insert the edges into the slots.
How do I store the cargo security screen when not in use?
- Pull up the luggage cover using the handle.
- Pull up a triangle-shaped cover.
- Place the cargo security screen on the lower portion of the cargo area.
What are the warnings regarding objects placed on the cargo security screen?
Do not place objects on the cargo security screen. Such objects may be thrown about inside the vehicle and possibly injure vehicle occupants during an accident or when braking.
What should I be careful of when placing luggage on the cargo security screen?
Do not place luggage on the cargo security screen. This may cause the security screen to become damaged or malformed.
How do I use the roof rack?
If the vehicle has a roof rack, you can load cargo on top of your vehicle. Crossbars and fixing components needed to install the roof rack on your vehicle may be obtained from an authorized Kia dealer or other qualified shop. The crossbars should be placed in the proper load carrying positions prior to placing items onto the roof rack.
What should I be aware of regarding sunroof operation when using the roof rack?
If the vehicle is equipped with a sunroof, be sure not to position cargo onto the roof rack in such a way that it could interfere with sunroof operation.
What should I do when the roof rack is not being used to carry cargo?
When the roof rack is not being used to carry cargo, the crossbars may need to be repositioned if wind noise is detected.
What are the cautions when loading the roof rack?
- When carrying cargo on the roof rack, take the necessary precautions to make sure the cargo does not damage the roof of the vehicle.
- When carrying large objects on the roof rack, make sure they do not exceed the overall roof length or width.
- When you are carrying cargo on the roof rack, do not operate the sunroof. This can damage the sunroof.
What is the maximum weight that can be loaded onto the roof rack?
The maximum weight that can be loaded onto the roof rack is 220 lbs (100 kg) evenly distributed.
What should I do when loading cargo onto the roof rack?
Distribute the load as evenly as possible across the crossbars and roof rack and secure the load firmly.
What should I be aware of when driving with items loaded onto the roof rack?
The vehicle center of gravity will be higher when items are loaded onto the roof rack. Avoid sudden starts, braking, sharp turns, abrupt maneuvers or high speeds that may result in loss of vehicle control or rollover resulting in an accident. Always drive slowly and turn corners carefully when carrying items on the roof rack. Severe wind updrafts, caused by passing vehicles or natural causes, can cause sudden upward pressure on items loaded on the roof rack. This is especially true when carrying large, flat items such as wood panels or mattresses. This could cause the items to fall off the roof rack and cause damage to your vehicle or others around you. To prevent damage or loss of cargo while driving, check frequently before or while driving to make sure the items on the roof rack are securely fastened.
What can happen if I load cargo or luggage in excess of the specified weight limit on the roof rack?
Loading cargo or luggage in excess of the specified weight limit on the roof rack may damage your vehicle.
What should I be aware of when driving with a roof load?
Always drive slow and turn corners carefully when carrying items on the roof rack. The vehicle center of gravity will be higher when items are loaded onto the roof rack.
What kind of signals does the shark fin antenna receive and transmit?
The shark fin antenna will receive the AM, FM broadcast signals and transmit data.
What should I be aware of regarding the steering wheel audio controls?
To avoid damaging the audio controls, do not operate the steering wheel control buttons simultaneously.
How do I control the volume using the steering wheel controls?
Press the lever upward to increase the volume and press the lever downward to decrease the volume.
What are the functions of the SEEK/PRESET button?
The SEEK/PRESET button has different functions based on the system mode.
- In RADIO mode, if the button is pressed for 1 second or more, it will function as the AUTO SEEK select button. If pressed for less than 1 second, it will function as the PRESET STATION buttons.
- In CD/USB/iPod® mode, if the button is pressed for 1 second or more, it will function as the FF/REW button. If pressed for less than 1 second, it will function as the TRACK UP/DOWN button.
How do I change the audio source using the steering wheel controls?
Press the MODE button to change audio source in the following order: FM(1~2) ➟ AM ➟ SAT(1~3) ➟ CD ➟ USB (iPod®) ➟ AUX ➟ MY MUSIC ➟ BT Audio ➟ FM…
How do I turn the audio on or off using the steering wheel controls?
Power on/off can be made by pressing the MODE button when the ignition switch is on ACC or ON.
- Power ON: Press the button when the audio is off
- Power OFF: Press the button for more than 1 second when the audio is on.
How do I use the MUTE button on the steering wheel?
Press the MUTE button to mute the sound. Press the MUTE button to turn off the microphone during a telephone call.
What should I be aware of regarding distracted driving and audio controls?
Driving while distracted can result in a loss of vehicle control that may lead to an accident, severe personal injury, and death. The driver’s primary responsibility is in the safe and legal operation of a vehicle, and use of any handheld devices, other equipment, or vehicle systems which take the driver’s eyes, attention and focus away from the safe operation of a vehicle or which are not permissible by law should never be used during operation of the vehicle.
How do I use the AUX and USB ports?
You can use the AUX port to connect audio devices and the USB port to plug in a USB device or iPod®.
What should I be aware of when using a portable audio device connected to the power outlet?
When using a portable audio device connected to the power outlet, noise may occur during playback. If this happens, use the power source of the portable audio device.
What kind of USB charging cable should I use?
Always use the USB charging cable that has been certified by the phone manufacturer. Use of aftermarket cables is not recommended.
How do AM and FM radio signals work?
AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your vehicle. This signal is then processed by the radio and sent to your vehicle speakers. However, in some cases the signal coming to your vehicle may not be strong and clear.
What can cause radio signal interference?
This can be due to factors, such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.
What is the difference between AM and FM reception?
AM broadcasts can be received at greater distances than FM broadcasts because AM radio waves are transmitted at low frequencies. These long distance, low frequency radio waves can follow the curvature of the earth rather than traveling straight. In addition, they curve around obstructions resulting in better signal coverage. FM broadcasts are transmitted at high frequencies and do not bend to follow the earth’s surface. Because of this, FM broadcasts generally begin to fade within short distances from the station. Also, FM signals are easily affected by buildings, mountains, and obstructions.
What are the normal conditions that do not indicate radio trouble?
- Fading – As your vehicle moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another station with a stronger signal.
- Flutter/Static – Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.
- Station Swapping – As an FM signal weakens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.
- Multi-Path Cancellation – Radio signals being received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the condition has passed.
What should I do if noise is produced from the audio system when using a cellular phone?
When a cellular phone is used inside the vehicle, noise may be produced from the audio system. This does not mean that something is wrong with the audio equipment. In such a case, try to operate mobile devices as far from the audio equipment as possible.
What should I be aware of when using a communication system such as a cellular phone or a radio set inside the vehicle?
When using a communication system such as a cellular phone or a radio set inside the vehicle, a separate external antenna must be fitted. When a cellular phone or a radio set is used with an internal antenna alone, it may interfere with the vehicle’s electrical system and adversely affect safe operation of the vehicle.
What are the warnings regarding cell phone use?
Do not use a cellular phone while driving. Stop at a safe and legal location to use a cellular phone.
What is the function of the EJECT button on the audio system?
The EJECT button ejects the disc.
What is the function of the RADIO button on the audio system?
The RADIO button changes to FM/AM/SiriusXM mode. Each time the button is pressed, the mode is changed in the order of FM1 ➟ FM2 ➟ AM ➟ SAT1 ➟ SAT2 ➟ SAT3.
What is the function of the MEDIA button on the audio system?
The MEDIA button changes to CD/USB(iPod®)/AUX/My Music/Bluetooth® Audio mode. Each time the button is pressed, the mode is changed in the order of CD ➟ USB(iPod®) ➟ AUX ➟ My Music ➟ BT (Bluetooth®) Audio.
What is the function of the PHONE button on the audio system?
The PHONE button changes to Phone mode. When a phone is not connected, the connection screen is displayed.
What is the function of the PWR/VOL knob on the audio system?
- Power knob : Press to turn power on/off.
- Volume knob : Turn left/right to control volume.
What is the function of the SEEK TRACK button on the audio system?
- When pressed briefly:
- Radio mode : plays previous/next frequency.
- Media (CD/USB/iPod®/My Music) modes : changes the track, Song(file).
- When pressed and held:
- Radio mode : continuously changes the frequency. Upon release, plays the current frequency.
- Media(CD/USB/iPod®/My Music) modes : rewinds or fast forwards the track or file.
- During a Handsfree call, controls the call volume.
What is the function of the RESET button on the audio system?
The RESET button is for forced system termination and system restart.
What is the function of the DISP button on the audio system?
The DISP button turns the monitor display on/off.
What is the function of the CLOCK button on the audio system?
- When pressed briefly : Display time screen
- When pressed and held : Move to the time setting mode
What is the function of the SCAN button on the audio system?
- Radio mode : previews all receivable broadcasts for 5 seconds each
- Media (CD/USB/My Music) modes : previews each song (file) for 10 seconds each.
What is the function of the SETUP button on the audio system?
The SETUP button changes to Setup mode.
What is the function of the TUNE knob on the audio system?
- Radio mode : turn to change broadcast frequencies.
- Media (CD/USB/iPod®/My Music) modes : turn to search Tracks/channels/files.
What is the function of the CAT/FOLDER button on the audio system?
- SiriusXM Radio : Category Search
- MP3 CD/USB mode : Search Folder.
What should I be aware of when using compact discs?
- Do not clean discs with chemical solutions, such as record sprays, antistatic sprays, antistatic liquids, benzene, or thinners.
- After using a disc, put the disc back in its original case to prevent disc scratches.
- Hold discs by their edges or within the center hole to prevent damage to disc surfaces.
- Do not introduce foreign substances into the disc insert/eject slot. Introducing foreign substances could damage the device interior.
- Do not insert two discs simultaneously.
- When using CD-R/CD-RW discs, differences in disc reading and playing times may occur depending on the disc manufacturer, production method and the recording method used.
- Clean fingerprints and dust off the disc surface (coated side) with a soft cloth.
- The use of CD-R/CD-RW discs attached with labels may result in disc slot jams or difficulties in disc removal. Such discs may also result in noise while playing.
- Some CD-R/CD-RW discs may not properly operate depending on the disc manufacturer, production method and the recording method used. If problems persist, try using a different CD as continued use may result in malfunctions.
- The performance of this product may differ depending on the CD-RW Drive Software.
- Copy-protected CDs such as S-type CDs may not function in the device. DATA discs cannot be played. (However, such discs may still operate but will do so abnormally).
- Do not use abnormally shaped discs (8cm, heart-shaped, octagon-shaped) as such discs could lead to malfunctions.
- If the disc is straddled on the disc slot without removal for 10 seconds, the disc will automatically be re-inserted into the disc player.
- Only genuine audio CDs are supported. Other discs may result in recognition failure. (e.g. copy CD-R, CDs with labels).
What should I be aware of when using USB devices?
- Connect the USB device after turning on the engine. The USB device may become damaged if it is already connected when the ignition is turned on. The USB device may not operate properly if the car ignition is turned on or off with the USB device connected.
- Be careful for static electricity when connecting/disconnecting USB devices.
- Encoded MP3 Players will not be recognized when connected as an external device.
- When connecting an external USB device, the vehicle’s audio system may not recognize the USB depending on what firmware is used by USB device or what files are on the USB.
- Only products formatted with byte/sectors under 64 Kb byte will be recognized.
- This device recognizes USB devices formatted in FAT 12/16/32 file formats. This device does not recognize files in NTFS file format.
- Some USB devices may not be supported due to compatibility issues.
- Avoid contact between the USB connector and bodily parts or foreign objects.
- Repeated connecting/disconnecting of USB devices within short periods of time may result in product malfunction.
- A strange noise may occur when disconnecting the USB.
- Make sure to connect/disconnect external USB devices with the audio power turned off.
- The amount of time required to recognize the USB device may differ depending on the type, size or file formats stored on the USB. Such differences in time are not indications of malfunctions.
- The vehicle audio system only supports USB devices designed to play music files.
- USB images and videos are not supported.
- Charging through the USB may not work for some mobile devices.
- The device may not support normal operation when using a typical USB memory device (miniature, keychain, etc.). For best results, use a typical USB device that has a metal case.
- The device may not support normal operation when using formats such as HDD Type, CF, or SD Memory.
- The device will not support files locked by DRM (Digital Rights Management).
- USB memory sticks used by connecting an Adaptor (SD Type or CF Type) may not be properly recognized.
- The device may not operate properly when using USB HDDs or USBs subject to connection failures caused by vehicle vibrations. (e.g. i-stick type).
- Avoid use of USB memory products that can also be used as key chains or mobile phone accessories. Use of such products may cause damage to the USB jack.
- Connecting an MP3 device or phone through various channels, such as AUX/BT or Audio/USB mode may result in pop noises or abnormal operation.
How should I use an iPod® with the vehicle’s audio system?
In order to use the iPod® with your vehicle’s audio system, you must use a dedicated iPod® cable (the cable that is supplied when purchasing iPod® /iPhone® products).
What should I be aware of when connecting an iPod® to the vehicle?
- If the iPod® is connected to the vehicle while it is playing, a high pitch sound could occur for approximately 1-2 seconds immediately after connecting. If possible, connect the iPod® to the vehicle with the iPod® stopped/paused.
- When the vehicle ignition is set to ACC or ON, connecting the iPod® through the iPod® cable will charge the iPod® through the car audio system.
- When connecting with the iPod® cable, make sure to fully insert the jack to prevent communication interference.
- When the EQ features of an external device, such as the iPod®, and the audio system are both active, EQ effects could overlap and cause sound deterioration and distortion. Whenever possible, turn off the EQ feature within the external device when it is connected to the audio system.
- Noise may occur when an iPod® or AUX device is connected. When such devices are not being used, disconnect the device for storage.
- When the iPod® or AUX device power is connected to the power jack, playing the external device may result in noise. In such cases, disconnect the power connection before use.
- Skipping or improper operation may occur depending on the characteristics of your iPod® /iPhone® device.
- Some iPod® products may not sync with the System depending on the version. If the Media is removed before the Media is recognized, then the system may not properly restore the previously operated mode. (iPad® charging is not supported.).
- Use an iPod® cable shorter than 1 meter in length such as the one originally supplied with a new iPod®, longer cables may lead to the audio system not recognizing the iPod®.
How do I play or pause Bluetooth audio?
Once a Bluetooth device is connected, the mode will automatically start. While playing, press the [II] button to pause and press [II] button to play. The play/pause feature may operate differently depending on the mobile phone.
How do I change Bluetooth audio files?
Press the [SEEK TRACK] button to move to the previous or next file.
What do I do if a Bluetooth device has not been connected?
Press the [SETUP] button then the [Phone] button to display the Bluetooth connection screen. You can use the pair phone, connect/disconnect, and delete features from your Bluetooth phone.
What do I do if music is not yet playing from my mobile device after converting to Bluetooth Audio mode?
Press the play button once which may start playing the mode. Make sure music is playing from the Bluetooth device after converting to Bluetooth Audio Mode.
What should I check if I’m streaming audio through Bluetooth?
Ensure the listening volume on the device is turned up.
What happens when I shortly press the steering wheel control button (1)?
It starts voice recognition. When selecting during a voice prompt, it stops the prompt and converts to a voice command waiting state.
What happens when I press and hold the steering wheel control button (1)?
It ends voice recognition.
What happens each time I press the steering wheel control button (2)?
The mode is changed in the order of FM1 ➟ FM2 ➟ AM ➟ SAT1 ➟ SAT2 ➟ SAT3 ➟ CD ➟ USB(iPod®) ➟ AUX ➟ My Music ➟ BT Audio. If the media is not connected or a disc is not inserted, corresponding modes will be disabled.
What does the steering wheel control button (3) do?
It is used to control volume.
What does the steering wheel control button (4) do?
It mutes the audio volume.
What does the steering wheel control button (5) do when pressed shortly in radio mode?
It searches broadcast frequencies saved to pre-sets.
What does the steering wheel control button (5) do when pressed shortly in media (CD/USB/iPod®/My Music/BT Audio) modes?
It changes the track, file or chapter.
What does the steering wheel control button (5) do when pressed and held in radio mode?
It automatically searches broadcast frequencies and channels.
What does the steering wheel control button (5) do when pressed and held in media (CD/USB/iPod®/My Music) modes?
It rewinds or fast forwards the track or song (file).
Is BT Audio mode supported in all mobile phones?
BT Audio mode may not be supported in some mobile phones.
What does the steering wheel control button (6) do when pressed shortly in the phone screen?
It displays the call history screen.
What does the steering wheel control button (6) do when pressed shortly in the dial screen?
It makes a call.
What does the steering wheel control button (6) do when pressed shortly in the incoming call screen?
It answers the call.
What does the steering wheel control button (6) do when pressed shortly during call waiting?
It switches to the waiting call (Call Waiting).
What does the steering wheel control button (6) do when pressed and held in Bluetooth Handsfree wait mode?
It redials the last call.
What does the steering wheel control button (6) do when pressed and held during a Bluetooth Handsfree call?
It switches the call back to mobile phone (Private).
What does the steering wheel control button (6) do when pressed while calling on the mobile phone?
It switches the call back to Bluetooth Handsfree (Operates only when Bluetooth Handsfree is connected).
What does the steering wheel control button (7) do?
It ends the phone call.
What should I do if no devices have been paired and I want to pair one?
Press the [PHONE] button or the [CALL] button on the steering wheel controls. Then press the [OK] button to enter the Pair Phone screen.
What is the “Vehicle Name” on the Bluetooth pairing screen?
It is the name of the device as shown when searching from your Bluetooth device.
What is the “Passkey” on the Bluetooth pairing screen?
It is the passkey used to pair the device.
What should I do on my Bluetooth device to pair with the car audio system?
Search and select your car audio system.
What do I do if I have a non-SSP (Secure Simple Pairing) supported device?
After a few moments, a screen will be displayed where the passkey is entered. Enter the passkey “0000” to pair your Bluetooth device with the car audio system.
What do I do if I have an SSP (Secure Simple Pairing) supported device?
After a few moments, a screen will display a 6-digit passkey. Check the passkey on your Bluetooth device and confirm.
What should I do if Bluetooth devices are paired but none are currently connected?
Pressing the [PHONE] button or the [CALL] button on the steering wheel controls displays the following screen. Press the [Pair] button to pair a new device or press the [Connect] to connect a previously paired device.
How do I pair a phone through the [PHONE] setup?
Press the [SETUP] button then select [Pair]. The following steps are the same as those described in the section “When No Devices have been Paired”.
How do I view the paired phone list?
Press the [SETUP] button then select [Phone] then select [Pair Phone List].
How do I connect a device from the paired phone list?
Select the device you want to connect and press the [Connect] button.
How do I disconnect a device from the paired phone list?
Select the currently connected device and press the [Disconnect] button.
How do I delete a device from the paired phone list?
Select the device you want to delete and press the [Delete] button.
What happens when I delete the currently connected device?
The device will automatically be disconnected to proceed with the deleting process.
What happens when a paired Bluetooth device is deleted?
The device’s call history and contacts data will also be deleted.
What do I need to do to re-use a deleted device?
You must pair the device again.
How do I change the priority of paired phones?
From the paired phone list, select the phone you want to switch to the highest priority, then press the [Change priority] button from the Menu. The selected device will be changed to the highest priority.
How do I display the Phone menu screen?
With a Bluetooth device connected, press the [PHONE] button.
What are the Phone menu options?
- Favorites: Up to 20 frequently used contacts can be saved for easy access
- Call History: Displays the call history list screen
- Contacts: Displays the Contacts list screen
- Dial Number: Displays the dial screen where numbers can be dialed to make calls
- Setup: Displays Phone related settings
What happens if I press the [Call History] button but there is no call history data?
A prompt is displayed which asks to download call history data.
What happens if I press the [Contacts] button but there is no contact data stored?
A prompt is displayed which asks to download contacts data.
Is the contact download feature supported on all mobile phones?
This feature may not be supported in some mobile phones. For more information on download support, refer to your mobile phone user’s manual.
What happens when I select a saved favorite contact?
It connects a call upon selection.
How do I add a favorite contact?
Downloaded contacts can be saved as favorites.
How do I delete all stored favorite contacts?
Select the “Delete All” option.
What do I need to do in order to save a favorite?
Contacts should be downloaded.
What happens if a contact saved in favorites has been updated in the phone?
The contact saved in favorites will not be automatically updated. To update Favorites, delete the Favorite and create a new Favorite.
How do I access the call history list?
Press the [Call History] button.
What does the call history list display?
A list of incoming, outgoing, and missed calls.
How do I download the call history?
Press the [Download] button.
What happens when I select a call from the call history?
It connects a call upon selection.
Will call history be saved in all mobile phones?
Call history may not be saved in the call history list in some mobile phones.
Will calls received with a hidden caller ID be saved?
Calls received with hidden caller ID will not be saved in the call history list.
When can I not call through the call history?
Calling through the call history is not possible when there is no call history stored or a Bluetooth phone is not connected.
How many calls can be stored in the call history?
Up to 50 received, dialed and missed calls are stored in Call History.
What call information is not saved?
Time of received/dialed calls and call time information are not saved.
How do I display the contacts list?
Press the [Contacts] button.
What does the contacts list display?
A list of saved phone book entries.
How do I download the contacts?
Press the [Download] button.
What happens when I select a contact from the contact list?
It connects a call upon selection.
How do I find a contact in alphabetical order?
Select the “Sort by” option.
How many contacts can be downloaded into the car contacts?
Up to 1,000 contacts saved in your Bluetooth phone can be downloaded.
Can contacts that have been downloaded to the car be edited or deleted on the phone?
No, contacts that have been downloaded to the car cannot be edited or deleted on the phone.
Are mobile phone contacts managed separately for each paired Bluetooth device?
Yes, mobile phone contacts are managed separately for each paired Bluetooth device (max 5 devices x 1,000 contacts each).
Is previously downloaded data maintained if the Bluetooth device has been disconnected?
Yes, previously downloaded data is maintained even if the Bluetooth device has been disconnected. However, the contacts and call history saved to the phone will be deleted if a paired phone is deleted.
Can I download contacts during Bluetooth streaming audio?
Yes, it is possible to download contacts during Bluetooth streaming audio.
What icon is displayed when downloading contacts?
The icon will be displayed within the status bar.
What do I do if I cannot begin downloading a contact list?
It is not possible to begin downloading a contact list when the contact download feature has been turned off within the Bluetooth device. In addition, some devices may require device authorization upon attempting to download contacts. If downloading does not normally occur, check the Bluetooth device settings or the screen state.
Is the contacts download feature supported in all mobile phones?
The contacts download feature may not be supported in some mobile phones. For more information of supported Bluetooth devices and function support, refer to your phone’s user manual.
How do I dial a number?
Use the Dial Pad to enter a phone number.
What does the “Call” button do on the dial screen?
If a number has been entered, it calls the number. If no number has been entered, it switches to the call history screen.
What does the “End” button do on the dial screen?
It deletes the entered phone number.
What does the “Delete” button do on the dial screen?
It deletes entered numbers one digit at a time.
What is displayed when answering a call with a Bluetooth device connected?
- Caller: Displays the other party’s name when the incoming caller is saved within your contacts
- Incoming Number: Displays the incoming number
- Accept: Accepts the incoming call
- Reject: Rejects the incoming call
Are most Audio and SETUP mode features enabled when an incoming call pop-up is displayed?
No, most Audio and SETUP mode features are disabled. Only the call volume will operate.
Will the telephone number be properly displayed in all mobile phones?
The telephone number may not be properly displayed in some mobile phones.
What is displayed during a handsfree call?
- Caller: Displays the other party’s name if the incoming caller is saved within your contacts
- Incoming Number: Displays the incoming number
- Call time: Displays the call time
- End: Ends call
- Private: Converts to Private mode
- Out Vol.: Sets call volume as heard by the other party
- Mute: Turns Mic Mute On/Off
What happens if the mic is muted?
The other party will not be able to hear your voice.
How do I start voice recognition?
Shortly press the button on the steering wheel controls.
What happens after starting voice recognition if prompt feedback is in [ON]?
The system will say “Please say a command after the beep (BEEP)”.
What happens after starting voice recognition if prompt feedback is in [OFF] mode?
The system will only say “(BEEP)”.
What should I do for proper voice recognition?
Say the command after the voice instruction and beep tone.
How do I change Prompt Feedback [ON]/[OFF]?
Go to [SETUP] then [System] then [Prompt Feedback].
What are some tips to improve Bluetooth voice recognition performance?
- Use full names vs. short or single syllable names (“John Smith” vs. “Dad”, “Smith Residence” vs. “Home”)
- Avoid using special characters or hyphens (@, &, #, /, -, *, +, etc.)
- Avoid using acronyms (“In Case Emergency" vs. “ICE”)
- Spell words completely, no abbreviations (“Doctor Goodman” vs. “Dr. Goodman”)
What should I do before speaking any commands?
Always wait for the beep before speaking any commands.
How do I skip prompt messages?
While a prompt message is being stated, shortly press the button on the steering wheel controls. The prompt message is immediately ended and the beep tone will sound. After the “Beep”, say the voice command.
How do I re-start voice recognition?
While the system waits for a command, shortly press the button on the steering wheel controls. The command wait state is immediately ended and the beep tone will sound. After the “Beep”, say the voice command.
What are some examples of mode commands?
You can say a radio type like ‘FM’, ‘AM’, or ‘Satellite’. You can also say a media source like ‘USB’, ‘My Music’, or ‘iPod®’. Additionally, there are phone commands like ‘Contacts’, ‘Call History’, or ‘Dial Number’.
What are some common voice commands that can be used in most operations?
- More Help: Provides guidance on commands that can be used anywhere in the system
- Help: Provides guidance on commands that can be used within the current mode
- Call : Calls saved in Contacts. Ex) Call “John Smith”
- Call on Mobile: Calls to the number that is saved as “Mobile” in Contacts. Ex) Call “John Smith” on Mobile
- Call in Office: Calls to the number that is saved as “Office” in Contacts. Ex) Call “John Smith” in Office
- Call at Home: Calls to the number that is saved as “Home” in Contacts Ex) Call “John Smith” at Home
- Call on Other: Calls to the number that is saved as “Other” in Contacts Ex) Call “John Smith” on Other
- Phone: Provides guidance on Phone related commands. After saying this command, say “Favorites”, “Call History”, “Contacts” or ”Dial Number” to execute corresponding functions
- Favorites: Displays the Favorite screen
- Call History: Displays the Call History screen
- Contacts: Displays the Contacts screen to automatically call
- Dial Number: Displays the Dial Number screen to call
- Redial: Connects the last dialed call number
- Tutorial: Provides guidance on how to use Voice Recognition and Bluetooth
- Radio: When listening to the radio, displays the next radio screen. When listening to a different mode, displays the most recently played radio screen. When currently listening to the FM1 or FM2, maintains the current state
What do the voice commands “FM 1(FM One)” and “FM 2(FM Two)” do?
“FM 1(FM One)” displays the FM1 screen. “FM 2(FM Two)” displays the FM2 screen.
What does the voice command “AM” do?
It displays the AM screen.
What do the voice commands “FM Preset 1~6” do?
It plays the most recently played broadcast saved in FM Preset 1~6.
What do the voice commands “AM Preset 1~6” do?
It plays the broadcast saved in AM Preset 1~6.
What do the voice commands “FM 87.5~107.9” do?
It plays the FM broadcast of the corresponding frequency.
What do the voice commands “AM 530~1710” do?
It plays the AM broadcast of the corresponding frequency.
What does the voice command “SIRIUS (Satellite)” do?
When listening to the SiriusXM®, it maintains the current state. When listening to a different mode, it displays the most recently played SiriusXM® screen.
What do the voice commands “SIRIUS (Satellite) 1~3” do?
It displays the selected SiriusXM® screen.
What does the voice command “SIRIUS Channel 0~223” do?
It plays the selected SiriusXM® channel.
What does the voice command “Media” do?
It moves to the most recently played media screen.
What does the voice command “CD” do?
It plays music on the CD.
What does the voice command “USB” do?
It plays music on the USB device.
What does the voice command “iPod®” do?
It plays music on the iPod®.
What does the voice command “My Music” do?
It plays music saved in My Music.
What does the voice command “AUX (Auxiliary)” do?
It plays the connected external device.
What does the voice command “Bluetooth® Audio” do?
It plays the music saved in connected Bluetooth device.
What does the voice command “Mute” do?
It mutes the sound.
What does the voice command “Cancel (Exit)” do?
It ends voice command.
What are some commands available during FM/AM Radio operation?
- Preset 1~6: Plays the broadcast station saved in Preset 1~6
- Scan: Scans receivable frequencies from the current broadcast and plays for 10 seconds each
- Preset Scan: Moves to the next preset from the current preset and plays for 10 seconds each
What are some commands that can be used with SiriusXM Radio?
- Channel 0~223: Plays the selected SiriusXM channel
- Scan: Scans receivable broadcast and plays for 10 seconds each
- Preset 1~6: Plays the broadcast saved in Preset 1~6
- Information: Displays the information screen
What are some commands available during Audio CD operation?
- Random: Randomly plays the tracks within the CD
- Random Off: Cancels random play to play tracks in sequential order
- Repeat: Repeats the current track
- Repeat Off: Cancels repeat play to play tracks in sequential order
- Track 1~30: Plays the desired track number
What are some commands available during MP3 CD/USB operation?
- Random: Randomly plays the files within the current folder
- Random Off: Cancels random play to play files in sequential order
- Repeat: Repeats the current file
- Repeat Off: Cancels repeat play to play files in sequential order
- Information: Displays the information screen of the current file
- Next Folder: Plays the first file in the next folder
- Previous Folder: Plays the first file in the previous folder
What are some commands available during iPod operation?
- Random: Randomly plays the songs within the current category
- Random Off: Cancels random play to play songs in sequential order
- Repeat: Repeats the current song
- Repeat Off: Cancels repeat play to play songs in sequential order
What are some commands available during My Music operation?
- Random: Randomly plays the songs within the current category
- Random Off: Cancels random play to play songs in sequential order
- Repeat: Repeats the current file
- Repeat Off: Cancels repeat play to play files in sequential order
- Delete: Deletes the current file. You will be prompted for additional confirmation
What are some commands available during Bluetooth audio streaming from mobile phone operation?
- Play: Plays the currently paused song
- Pause: Pauses the current song
How do I access the Setup screen?
Press the [SETUP] button.
What options can I control from the Setup screen?
You can select and control options related to [Display], [Sound], [Clock/Calendar], [Phone] and [System].
What Display options can I control?
You can select and control options related to [Brightness], [Mode Pop up] and [Media Display].
How do I adjust the screen brightness?
Use the [Left/Right] buttons to adjust the screen brightness or set the Brightness on Automatic, Day or Night mode. Press the [Default] button to reset.
What are the screen brightness options?
- Automatic: Adjusts the brightness automatically
- Day: Always maintains the brightness on high
- Night: Always maintains the brightness on low
What is the “Mode Pop up” feature used for?
This feature is used to display the Mode Pop up screen when entering radio and media modes. When this feature is turned on, pressing the [RADIO] or [MEDIA] button will display the Mode Pop up screen.
When can the media Mode Pop up screen be displayed?
The media Mode Pop up screen can be displayed only when two or more media modes have been connected.
What is the “Media Display” feature used for?
This feature is used to change the information displayed within USB and MP3 CD modes.
What are the “Media Display” options?
- Folder File: Displays file name and folder name
- Album Artist Song: Displays album name/artist name/song name
What Sound options can I control?
You can select and control options related to [Sound Settings], [Speed Dependent Vol.], [Voice Recognition Vol.] and [Touch Screen Beep].
How do I adjust the Fader/Balance settings?
Use the [Up/Down/Left/Right] buttons.
How do I adjust the Bass/Middle/Treble settings?
Use the [Left/Right] buttons.
How do I reset the Sound settings?
Press the [Default] button.
What is SDVC (Speed Dependent Volume Control)?
The volume level is controlled automatically according to the vehicle speed.
How do I set SDVC?
Select from On/Off.
How do I adjust the Voice Recognition volume?
Use the [-], [+] buttons.
What is the “Touch Screen Beep” feature used for?
This feature is used to turn the touch screen beep on/off.
What Clock/Calendar options can I control?
You can select and control options related to [Clock Settings], [Calendar Settings], [Time Format] and [Clock Display].
How do I set the Hour, Minutes and AM/PM setting?
Use the [Up/Down] buttons.
How do I display the Clock/Calendar screen?
Press and hold the [CLOCK] button.
How do I set the Day, Month and Year setting?
Use the [Up/Down] buttons.
What is the “Time Format” feature used for?
This feature is used to change the clock format between 12hr or 24hr.
What is the “Clock Display” feature used for?
This feature is used to display a clock on the screen when the audio system is turned off.
What Phone options can I control?
You can select and control options related to [Pair Phone], [Paired Phone List], [Contacts Download], [Auto Download], [Outgoing Volume] and [Bluetooth System Off].
How can Bluetooth devices be paired with the audio system?
Refer to the “Pairing through Phone Setup” section within Bluetooth.
What is the Paired Phone List feature used for?
This feature is used to view mobile phones that have been paired with the audio system. Upon selecting a paired phone, the setup menu is displayed. For more information, refer to the “Setting Bluetooth Connection” section within Bluetooth.
What are the options in the paired phone setup menu?
- (1) Moves to the previous screen
- (2) Connect/Disconnect Phone: Connects/Disconnects currently selected phone
- (3) Delete: Deletes the currently selected phone
- (4) Change priority: Sets currently selected phone to highest connection priority
What should I do before downloading contacts?
Only contacts within connected phones can be downloaded. Also check to see that your mobile phone supports the download feature.
How do I check if my phone supports contact downloads?
Refer to your mobile phone user’s manual.
Can I download contacts for only the connected phone?
Yes, the contacts for only the connected phone can be downloaded.
What happens when downloading phone contacts?
The previous corresponding data is deleted and a download progress bar is displayed.
Can I use Voice Recognition while contacts are being downloaded?
No, Voice Recognition may not operate while contacts are being downloaded.
How do I adjust the outgoing volume level?
Use the [-], [+] buttons.
How do I change the volume during a call?
Use the [SEEK TRACK] button.
What happens when Bluetooth is turned off?
Bluetooth related features will not be supported within the audio system.
How do I turn Bluetooth back on?
Go to [SETUP] then [Phone] and press “Yes”.
What System options can I control?
You can select and control options related to [Memory Information], [Prompt Feedback] and [Language].
What does the “Memory Information” feature display?
It displays information related to system memory.
What information is displayed in “Memory Information”?
- Using: Displays capacity currently in use
- Capacity: Displays total capacity
What are the “Prompt Feedback” options?
- ON: When using voice recognition, provides detailed guidance prompts
- OFF: When using voice recognition, omits some guidance prompts
What does the “Language” feature do?
This feature is used to change the system and voice recognition language. If the language is changed, the system will restart and apply the selected language.
What are some important things to be aware of before driving the vehicle?
- Be sure that all windows, outside mirror(s), and outside lights are clean.
- Check the condition of the tires.
- Check under the vehicle for any sign of leaks.
- Be sure there are no obstacles behind you if you intend to back up.
What fluid levels should be checked regularly?
Fluid levels, such as engine oil, engine coolant, brake fluid, and washer fluid should be checked on a regular basis, at the exact interval depending on the fluid.
What should be done before starting the vehicle?
- Close and lock all doors.
- Position the seat so that all controls are easily reached.
- Buckle your seat belt.
- Adjust the inside and outside rearview mirrors.
- Be sure that all lights work.
- Check all gauges.
- Check the operation of warning lights when the ignition switch is turned to the ON position.
- Release the parking brake and make sure the brake warning light goes out.
What should a driver focus on while driving?
Focus on the road while driving. The driver’s primary responsibility is in the safe and legal operation of the vehicle.
What should a driver not do while operating a vehicle?
Use of any handled devices, other equipment or vehicle systems that distract the drive should not be used during vehicle operation.
What should I do before putting the vehicle in D (Drive) or R (Reverse)?
Always check the surrounding areas near your vehicle for people, especially children.
What should I do to avoid a fire risk when parking or stopping with the engine on?
Be careful not to depress the accelerator pedal for a long period of time. It may overheat the engine or exhaust system and cause fire.
What should I do with loose objects inside the vehicle?
Securely store items in your vehicle. When you make a sudden stop or turn the steering wheel rapidly, loose objects may drop on the floor and it could interfere with the operation of the foot pedals, possibly causing an accident.
What should I avoid when driving?
Do not drive while intoxicated. Drinking and driving is dangerous.
What can affect reflexes, perceptions and judgment?
Even a small amount of alcohol will affect your reflexes, perceptions and judgment. Driving while under the influence of drugs is as dangerous as or more dangerous than driving drunk.
When does the ignition switch illuminate?
Whenever a front door is opened, the ignition switch will illuminate for your convenience, provided the ignition switch is not in the ON position.
When does the ignition switch light go off?
The light will go off immediately when the ignition switch is turned on. It will also go off after about 30 seconds when the door is closed.
When can the ignition key be removed?
The ignition key can be removed only in the LOCK position.
What does the ACC (Accessory) position do?
The electrical accessories are operative. If difficulty is experienced turning the ignition switch to the ACC position, turn the key while turning the steering wheel right and left to release the tension.
What does the ON position do?
The warning lights can be checked before the engine is started. This is the normal running position after the engine is started. Do not leave the ignition switch ON if the engine is not running to prevent battery discharge.
What does the START position do?
Turn the ignition switch to the START position to start the engine. The engine will crank until you release the key; then it returns to the ON position. The brake warning light can be checked in this position.
What should I always do before leaving the driver’s seat?
Always make sure the shift lever is engaged in P (Park) for automatic transaxle, set the parking brake fully and shut the engine off. Unexpected and sudden vehicle movement may occur if these precautions are not taken.
How should you drive in AWD?
Slow down and be ready for changes in the composition and traction of the surface under your tires. If you have any doubt about the safety of the conditions you are facing, stop and consider the best way to proceed. Do not exceed your own ability or your vehicle’s ability to operate safely.
What should you avoid when driving in deep standing water or mud?
Do not try to drive in deep standing water or mud since such conditions can stall your engine and clog your exhaust pipes.
What should you avoid when driving down steep hills?
Do not drive down steep hills since it requires extreme skill to maintain control of the vehicle.
When driving up or down hills, what is the recommended way to drive?
When you are driving up or down hills drive as straight as possible. Use extreme caution in going up or down steep hills, since you may flip your vehicle over depending on the grade, terrain and water/mud conditions.
What is an important thing to learn when driving an AWD vehicle?
You must consciously take the effort to learn how to corner in a AWD vehicle. Do not rely on your experience in conventional FWD vehicles in choosing safe cornering speed in AWD mode. For starters, you must drive more slowly in AWD.
Why should you drive carefully off-road?
Drive carefully off-road because your vehicle may be damaged by rocks or roots of trees. Become familiar with the off-road conditions where you are going to drive before you begin driving.
What should you always do when driving off-road?
Always hold the steering wheel firmly when you are driving off-road.
What should you make sure all passengers do when driving?
Make sure all passengers are wearing seat belts.
What should you not do with the steering wheel when driving off-road?
Do not grab the inside of the steering wheel when you are driving off-road. You may hurt your arm by a sudden steering maneuver or from steering wheel rebound due to impact with objects on the ground. You could also lose control of your steering wheel while driving on rough terrain.
What should you do when driving in heavy wind?
If you are driving in heavy wind, the vehicle’s higher center of gravity decreases your steering control capacity and requires you to drive more slowly.
What should you do when turning corners in an AWD vehicle?
Reduce speed when you turn corners. The center of gravity of AWD vehicles is higher than that of conventional FWD vehicles, making them more likely to roll over when you turn corners too fast.
If you need to drive in the water, what steps should you take?
If you need to drive in the water, stop your vehicle, set your transfer to the AWD LOCK mode and drive at less than 5 mph (8 km/h). Do not drive in water if the level is higher than the bottom of the vehicle.
What should you do after driving through mud or water?
Check your brake condition once you are out of mud or water. Press the brake pedal several times as you move slowly until you feel normal braking forces return.
When should you shorten your scheduled maintenance interval?
Shorten your scheduled maintenance interval if you drive in off-road conditions such as sand, mud or water. Always wash your vehicle thoroughly after off-road use, especially cleaning the bottom of the vehicle.
What should you make sure of regarding your tires when driving an AWD vehicle?
Be sure to equip the vehicle with four tires of the same size and type.
How should a full time all wheel drive vehicle be towed?
A full time all wheel drive vehicle cannot be towed by an ordinary tow truck. Make sure that the vehicle is placed on a flat bed truck for moving.
What is a warning about driving through water?
Drive slowly. If you are driving too fast in water, the water can get into the engine compartment and wet the ignition system, causing your vehicle to suddenly stop. If this happens and your vehicle is in a tilted position, your vehicle may roll over.
What should you avoid when driving an AWD vehicle?
Avoid high cornering speed and do not make quick steering wheel movements, such as sharp lane changes or fast, sharp turns.
What is an increased risk if you lose control of your vehicle at high speed?
The risk of rollover is greatly increased if you lose control of your vehicle at high speed.
What should you do if your vehicle leaves the roadway?
In the event your vehicle leaves the roadway, do not steer sharply. Instead, slow down before pulling back into the travel lanes.
What are some steps a driver can take to reduce the risk of a rollover?
If at all possible, avoid sharp turns or abrupt maneuvers, do not load your roof rack with heavy cargo, and never modify your vehicle in any way.
What should you do if one of the front or rear wheels begins to spin in mud or snow?
If one of the front or rear wheels begins to spin in mud, snow, etc. the vehicle can sometimes be driven out by depressing the accelerator pedal further; however, do not run the engine continuously at high rpms to free the vehicle from snow or mud because doing so could damage the AWD system.
What should you always use when replacing tires?
Always use the size and type of tires recommended in the tire section of the manual. Installation of variant tires can affect the safety and performance of your vehicle.
How should full-time AWD vehicles be tested?
Full-time AWD vehicles must be tested on a special four wheel chassis dynamometer. Never engage the parking brake while performing these tests.
What should you do if a FWD roll tester must be used?
If a FWD roll tester must be used, perform the following: Check the tire pressures recommended for your vehicle. Place the front wheels on the roll tester for a speedometer test. Release the parking brake. Place the rear wheels on the temporary free roller.
What is a notice about lifting up a vehicle?
When lifting up the vehicle, do not operate front and rear wheel separately. All four wheels should be operated. If you need to operate the front wheel and rear wheel when lifting up the vehicle, you should release the parking brake.
What is a warning about a jacked vehicle?
While the full-time AWD vehicle is being raised on a jack, never start the engine or cause the tires to rotate. There is the danger that rotating tires touching the ground could cause the vehicle to go off the jack and to jump forward.
What is a warning about dynamometer testing?
Keep away from the front of the vehicle while the vehicle is in gear on the dynamometer. This is very dangerous as the vehicle can jump forward and cause serious injury or death.
What should you do if the power-assisted brakes lose power?
In the event that the power-assisted brakes lose power because of a stalled engine or some other reason, you can still stop your vehicle by applying greater force to the brake pedal than you normally would. The stopping distance, however, will be longer. When the engine is not running, the reserve brake power is partially depleted each time the brake pedal is applied.
What should you not do when the power assist has been interrupted?
Do not pump the brake pedal when the power assist has been interrupted. Pump the brake pedal only when necessary to maintain steering control on slippery surfaces.
What should you do if you think your brakes might be wet?
Applying the brakes lightly will indicate whether they have been affected in this way. Always test your brakes in this fashion after driving through deep water.
How can you dry the brakes?
To dry the brakes, apply them lightly while maintaining a safe forward speed until brake performance returns to normal.
What should you avoid when descending a long or steep hill?
Avoid continuous application of the brakes when descending a long or steep hill by shifting to a lower gear. Continuous brake application will cause the brakes to overheat and could result in a temporary loss of braking performance.
What should you not do with your foot on the brake pedal?
Do not drive with your foot resting on the brake pedal. This will create abnormally high brake temperatures which can cause excessive brake lining and pad wear.
What can you do to make an emergency stop if the service brakes fail?
If service brakes fail to operate while the vehicle is in motion, you can make an emergency stop with the parking brake. The stopping distance, however, will be much greater than normal.
What will you hear when your brake pads are worn?
When your brake pads are worn and new pads are required, you will hear a high-pitched warning sound from your front brakes or rear brakes.
What should you always do when replacing brake pads?
Always replace the front or rear brake pads as pairs.
What should you avoid doing with the parking brake while the vehicle is moving?
Avoid applying the parking brake to stop the vehicle while it is moving except in an emergency situation.
What can happen if you apply the parking brake while the vehicle is moving at normal speeds?
Applying the parking brake while the vehicle is moving at normal speeds can cause a sudden loss of control of the vehicle. If you must use the parking brake to stop the vehicle, use great caution in applying the brake.
What is a warning about ignoring high pitched wear sounds from your brakes?
Do not ignore high pitched wear sounds from your brakes. If you ignore this audible warning, you will eventually lose braking performance, which could lead to a serious accident.
What is a caution about driving with worn brake pads?
Do not continue to drive with worn brake pads. Continuing to drive with worn brake pads can damage the braking system and result in costly brake repairs.
How do you apply the foot type parking brake?
To engage the parking brake, first apply the foot brake and then depress the parking brake pedal down as far as possible.
How do you release the foot type parking brake?
To release the parking brake, depress the parking brake pedal a second time while applying the foot brake. The pedal will automatically extend to the fully released position.
What is a caution about driving with the parking brake applied?
Driving with the parking brake applied will cause excessive brake pad (or lining) and brake rotor wear.
What is a warning about parking brake use?
All vehicles should always have the parking brake fully engaged when parked to avoid inadvertent movement of the vehicles which can injure occupants or pedestrians.
What should you check before driving, in regards to the brake warning light?
Check the brake warning light by turning the ignition switch ON (do not start the engine). This light will be illuminated when the parking brake is applied with the ignition switch in the START or ON position. Before driving, be sure the parking brake is fully released and the brake warning light is off. If the brake warning light remains on after the parking brake is released while the engine is running, there may be a malfunction in the brake system. Immediate attention is necessary.
If the brake warning light remains on after releasing the parking brake, what should you do?
If at all possible, cease driving the vehicle immediately. If that is not possible, use extreme caution while operating the vehicle and only continue to drive the vehicle until you can reach a safe location or repair shop.
How do you apply the EPB (electronic parking brake)?
To apply the EPB (electronic parking brake): Depress the brake pedal and pull up the EPB switch. Make sure the warning light comes on. Also, the EPB is applied automatically if the Auto Hold button is on when the engine is turned off. However, if you press the EPB switch after the engine is turned off, the EPB will not be applied.
When should you apply the EPB on a steep incline or when pulling a trailer?
On a steep incline or when pulling a trailer, if the vehicle does not remain at a standstill, apply the EPB and pull up the EPB switch for more than 3 seconds.
What should you not do with the parking brake or EPB while the vehicle is moving?
Do not operate the parking brake/ EPB while the vehicle is moving except in an emergency situation.
Is a click or electric brake motor whine sound while operating or releasing the EPB normal?
A click or electric brake motor whine sound may be heard while operating or releasing the EPB, but these conditions are normal and indicate that the EPB is functioning properly.
How do you release the EPB (electronic parking brake)?
To release the EPB (electronic parking brake), press the EPB switch while doing the following: Have the ignition switch or engine start/stop button in the ON position. Depress the brake pedal. The shift lever must be in P (Park). Make sure the brake warning light goes off.
How do you release the EPB (electronic parking brake) automatically?
To release EPB (electronic parking brake) automatically: Shift lever in P (Park) With the engine running depress the brake pedal and shift out of P (Park) to R (Reverse) or D (Drive). Shift lever in N (Neutral) With the engine running depress the brake pedal and shift out of N (Neutral) to R (Reverse) or D (Drive). Automatic Transaxle 1. Start the engine. 2. Fasten the driver’s seat belt. 3. Close the driver’s door, engine hood and tailgate. 4. Depress the accelerator pedal while the shift lever is in R (Rear), D (Drive) or manual mode. Make sure the brake warning light goes off.
Can you engage the EPB when the ignition is off, and can you release it?
For your safety, you can engage the EPB even though the ignition switch or engine stop/start button is in the OFF position, but you cannot release it.
When should you manually release the parking brake with the EPB switch?
For your safety, depress the brake pedal and release the parking brake manually with the EPB switch when you drive downhill or when backing up the vehicle. Do not follow the above procedure when driving on a flat level ground. The vehicle may suddenly move forward.
What should you do if the parking brake warning light is still on even though the EPB has been released?
If the parking brake warning light is still on even though the EPB has been released, have the system checked by an authorized Kia dealer.
When might the EPB (electronic parking brake) be automatically applied?
EPB (electronic parking brake) may be automatically applied when: The EPB is overheated or requested by other systems. If the driver turns the engine off by mistake while Auto Hold is operating, EPB will be automatically applied.
What is a caution about driving with the EPB applied?
Do not drive your vehicle with the EPB applied. It may cause excessive brake pad and brake rotor wear.
What warning will you hear if you try to drive off with the EPB applied?
If you try to drive off depressing the accelerator pedal with the EPB applied, but the EPB doesn’t release automatically, a warning will sound and a message will appear.
What other warning sounds and messages might you hear?
If the driver’s seat belt is not fastened and the engine hood, driver’s door or trunk is opened, a warning will sound and a message will appear. If there is a problem with the vehicle, a warning may sound and a message may appear.
If any of the above warning situations occur, what should you do?
If the above situation occurs, depress the brake pedal and release EPB by pressing the EPB switch.
When leaving your keys with a parking lot attendant or valet, what should you do?
When leaving your keys with a parking lot attendant or valet, make sure to inform him/her how to operate the EPB.
What is a warning about the EPB malfunctioning?
The EPB may malfunction if you drive with the EPB applied.
How should you depress the accelerator when automatically releasing the EPB?
When you automatically release EPB by depressing the accelerator pedal, depress it slowly.
What is a warning about parking brake use?
All vehicles should always have the parking brake fully engaged when parked to avoid inadvertent movement of the car which can injure occupants or pedestrians.
How do you disengage the EPB?
To disengage EPB, fasten seatbelt, close door, hood, and trunk.
What happens when the conversion from Auto Hold to EPB is not working properly?
When the conversion from Auto Hold to EPB is not working properly a warning will sound and a message will appear.
What should you do when the message appears that the Auto Hold and EPB may not activate?
Depress the brake pedal.
What happens if the EPB is applied while Auto Hold is activated because of ESC (Electronic Stability Control) signal?
If the EPB is applied while Auto Hold is activated because of ESC (Electronic Stability Control) signal, a warning will sound and a message will appear.
What does the EPB malfunction indicator light mean?
This warning light illuminates if the engine start/stop button is changed to the ON position and goes off in approximately 3 seconds if the system is operation normally. If the EPB malfunction indicator remains on, comes on while driving, or does not come on when the ignition switch or the engine start/stop button is changed to the ON position, this indicates that the EPB may have malfunctioned. If this occurs, have your vehicle checked by an authorized Kia dealer as soon as possible.
What does it mean if the EPB malfunction indicator illuminates when the ESC indicator comes on?
The EPB malfunction indicator may illuminate when the ESC indicator comes on to indicate that the ESC is not working properly, but it does not indicate a malfunction of the EPB.
What should you do if the EPB warning light illuminates if the EPB switch operates abnormally?
Shut the engine off and turn it on again after a few minutes. The warning light will go off and the EPB switch will operate normally. However, if the EPB warning light is still on, have the system checked by an authorized Kia dealer.
What should you do if the parking brake warning light does not illuminate or blinks?
If the parking brake warning light does not illuminate or blinks even though the EPB switch was pulled up, the EPB is not applied. If the parking brake warning light blinks when the EPB warning light is on, press the switch, then pull it up. Once more press it back to its original position and pull it back up. If the EPB warning does not go off, have the system checked by an authorized Kia dealer.
How can you use the EPB for emergency braking?
If there is a problem with the brake pedal while driving, emergency braking is possible by pulling up and holding the EPB switch. Braking is possible only while you are holding the EPB switch. During emergency braking by the EPB, the parking brake warning light will illuminate to indicate that the system is operating.
What should you do if you notice a continuous noise or burning smell when the EPB is used for emergency braking?
If you notice a continuous noise or burning smell when the EPB is used for emergency braking, have your vehicle checked by an authorized Kia dealer.
What should you do if the EPB does not release normally?
If the EPB does not release normally, take your vehicle to an authorized Kia dealer by loading the vehicle on a flatbed tow truck and have the system checked.
What is a warning about operating the electronic parking brake while the vehicle is moving?
Do not operate the electronic parking brake while the vehicle is moving except in an emergency situation. Applying the electronic parking brake while the vehicle is moving at normal speeds can cause a sudden loss of control of the vehicle. If you must use the electronic parking brake to stop the vehicle, use great caution in applying the brake.
How does the Auto Hold system work?
The Auto Hold maintains the vehicle in a standstill even though the brake pedal is not depressed after the driver brings the vehicle to a complete stop by depressing the brake pedal.
How do you engage the Auto Hold system?
Depress the brake pedal, start the engine and then press the Auto Hold button. The white AUTO HOLD indicator will come on indicating the system is in standby. Before the Auto Hold will engage, the driver’s door, engine hood must be closed and the driver’s seat belt must be fastened.
How do you know when Auto Hold is engaged?
When coming to a complete stop by depressing the brake pedal, the AUTO HOLD indicator changes from white to green indicating the AUTO HOLD is engaged and EPB is applied. The vehicle will remain at a standstill even if you release the brake pedal.
What will release Auto Hold?
If EPB is applied, Auto Hold will be released. If you press the accelerator pedal with the shift lever in D (Drive) or manual mode, the Auto Hold will be released automatically and the vehicle will start to move. The indicator changes from green to white indicating the Auto Hold is in standby and the EPB is released.
What should you check when driving off from Auto Hold?
When driving off from Auto Hold by depressing the accelerator pedal, always check the surrounding area near your vehicle. Slowly depress the accelerator pedal for a smooth launch.
How do you cancel the Auto Hold operation?
To cancel the Auto Hold operation, press the Auto Hold switch. The AUTO HOLD indicator will go out. To cancel the Auto Hold operation when the vehicle is at a standstill, press the Auto Hold switch while depressing the brake pedal.
When will the Auto Hold not engage?
The following are conditions when the Auto Hold will not engage: The driver’s seat belt is unfastened and driver’s door is opened. The engine hood is opened. The shift lever is in P (Park) or R (Reverse). The EPB is applied.
When will the Auto Hold automatically switch to EPB?
The Auto Hold automatically switches to EPB under any of the following conditions: The driver’s seat belt is unfastened and driver’s door is opened. The engine hood is opened. The vehicle is in a standstill for more than 10 minutes. The vehicle is standing on a steep slope. The vehicle moved several times. In these cases, the brake warning light comes on, the AUTO HOLD indicator changes from green to white, and a warning sounds and a message will appear to inform you that EPB has been automatically engaged.
What should you do before driving off again after Auto Hold switches to EPB?
Before driving off again, press foot brake pedal, check the surrounding area near your vehicle and release parking brake manually with the EPB switch.
What should you do if the AUTO HOLD indicator lights up yellow?
If the AUTO HOLD indicator lights up yellow, the Auto Hold is not working properly. Take your vehicle to an authorized Kia dealer and have the system checked.
What should you do if there is a malfunction with the driver’s door or engine hood open detection system?
If there is a malfunction with the driver’s door, engine hood open detection system, the Auto Hold may not work properly. Take your vehicle to an authorized Kia dealer and have the system checked.
What does it mean if you hear a click or electric brake motor whine sound while operating or releasing the EPB?
A click or electric brake motor whine sound may be heard while operating or releasing the EPB, but these conditions are normal and indicate that the EPB is functioning properly.
What warning will you hear when the EPB is applied from Auto Hold?
When the EPB is applied from Auto Hold, a warning will sound and a message will appear.
What is a warning about activating Auto Hold?
To reduce the risk of an accident, do not activate Auto Hold while driving downhill, backing up or parking your vehicle.
What should you do when the message ‘AUTO HOLD deactivating. Press brake pedal’ appears?
When the conversion from Auto Hold to EPB is not working properly a warning will sound and a message will appear. Depress the brake pedal.
What will happen if you do not apply the brake pedal when you release the Auto Hold by pressing the Auto Hold switch?
If you do not apply the brake pedal when you release the Auto Hold by pressing the [AUTO HOLD] switch, a warning will sound and a message will appear.
What warning will you hear if the driver’s door or engine hood are not closed or the driver’s seat belt is unfastened?
When you press the [AUTO HOLD] switch, if the driver’s door, engine hood are not closed or the driver’s seat belt is unfastened, a warning will sound and a message will appear on the LCD display.
What should you do if the driver’s door or engine hood are not closed or the driver’s seat belt is unfastened and you want to use Auto Hold?
At this moment, press the [AUTO HOLD] button after closing the driver’s door, engine hood and fastening the seat belt.
Will ABS (or ESC) prevent accidents due to improper or dangerous driving maneuvers?
ABS (or ESC) will not prevent accidents due to improper or dangerous driving maneuvers. Even though vehicle control is improved during emergency braking, always maintain a safe distance between you and objects ahead.
When should vehicle speeds be reduced?
Vehicle speeds should always be reduced during extreme road conditions such as when driving on rough, gravel or snow-covered roads, when driving with tire chains installed, or when driving on roads where the road surface is pitted or has different surface heights.
What might you hear or feel when the ABS is active?
When you apply your brakes under conditions which may lock the wheels, you may hear a “tik-tik’’ sound from the brakes, or feel a corresponding sensation in the brake pedal. This is normal and it means your ABS is active.
How should you apply the brakes in an emergency situation to get the maximum benefit from the ABS?
In order to obtain the maximum benefit from your ABS in an emergency situation, do not attempt to modulate your brake pressure and do not try to pump your brakes. Press your brake pedal as hard as possible or as hard as the situation allows the ABS to control the force being delivered to the brakes.
What does it mean if you hear a click sound in the engine compartment when the vehicle begins to move after the engine is started?
A click sound may be heard in the engine compartment when the vehicle begins to move after the engine is started. These conditions are normal and indicate that the anti-lock brake system is functioning properly.
What should you always maintain, even with the anti-lock brake system?
Even with the anti-lock brake system, your vehicle still requires sufficient stopping distance. Always maintain a safe distance from the vehicle in front of you.
What should you always do when cornering?
Always slow down when cornering. The anti-lock brake system cannot prevent accidents resulting from excessive speeds.
What might happen on loose or uneven road surfaces when the anti-lock brake system is operating?
On loose or uneven road surfaces, operation of the anti-lock brake system may result in a longer stopping distance than for vehicles equipped with a conventional brake system.
What does it mean if the ABS warning light stays on?
The ABS warning light will stay on for approximately 3 seconds after the ignition switch is ON. During that time, the ABS will go through self-diagnosis and the light will go off if everything is normal. If the light stays on, you may have a problem with your ABS. Contact an authorized Kia dealer as soon as possible.
What is the Electronic Stability Control (ESC) system designed to do?
The Electronic Stability Control (ESC) system is designed to stabilize the vehicle during cornering maneuvers. ESC checks where you are steering and where the vehicle is actually going. ESC applies the brakes on individual wheels and intervenes with the engine management system to stabilize the vehicle.
Will Electronic Stability Control (ESC) prevent accidents?
Electronic stability control (ESC) will not prevent accidents. Excessive speed in turns, abrupt maneuvers and hydroplaning on wet surfaces can still result in serious accidents. Only a safe and attentive driver can prevent accidents by avoiding maneuvers that cause the vehicle to lose traction. Even with ESC installed, always follow all the normal precautions for driving – including driving at safe speeds for the conditions.
What is the driver’s responsibility, even with ESC installed?
It is still your responsibility to drive and corner at reasonable speeds and to leave a sufficient margin of safety.
What might you hear or feel when the ESC is active?
When you apply your brakes under conditions which may lock the wheels, you may hear a “tik-tik’’ sound from the brakes, or feel a corresponding sensation in the brake pedal. This is normal and it means your ESC is active.
What does it mean if you hear a click sound in the engine compartment when the vehicle begins to move after the engine is started?
A click sound may be heard in the engine compartment when the vehicle begins to move after the engine is started. These conditions are normal and indicate that the Electronic Stability Control System is functioning properly.
When is ESC turned on?
When the ignition is turned ON, ESC and ESC OFF indicator lights illuminate for approximately 3 seconds, then ESC is turned on.
How can you turn ESC off?
Press the ESC OFF button for at least half a second after turning the ignition ON to turn ESC off. (ESC OFF indicator will illuminate).
How can you turn the ESC back on?
To turn the ESC on, press the ESC OFF button (ESC OFF indicator light will go off).
Is a ticking sound when starting the engine normal?
When starting the engine, you may hear a slight ticking sound. This is the ESC performing an automatic system self-check and does not indicate a problem.
How do you know when the ESC is in operation?
When the ESC is in operation, the ESC indicator light blinks. When the Electronic Stability Control is operating properly, you can feel a slight pulsation in the vehicle. This is only the effect of brake control and indicates nothing unusual.
What might happen when moving out of the mud or driving on a slippery road?
When moving out of the mud or driving on a slippery road, pressing the accelerator pedal may not cause the engine rpm (revolutions per minute) to increase.
What are the 2 kinds of ESC off states?
This car has 2 kinds of ESC off states. If the engine stops when ESC is off, ESC remains off. Upon restarting the engine, the ESC will automatically turn on again.
How do you cancel ESC operation in ESC off state 1?
To cancel ESC operation, press the ESC OFF button shortly (ESC OFF indicator light illuminates). At this state, the engine control function does not operate. It means the traction control function does not operate. Brake control function only operates.
How do you cancel ESC operation in ESC off state 2?
To cancel ESC operation, press the ESC OFF button for more than 3 seconds. ESC OFF indicator light illuminates and ESC OFF warning chime will sound. At this state, the engine control function and brake control function do not operate. It means the car stability control function does not operate any more.
What does the ESC indicator light mean?
When ignition switch is turned to ON, the indicator light illuminates, then goes off if the ESC system is operating normally. The ESC indicator light blinks whenever ESC is operating or illuminates when ESC fails to operate. The ESC OFF indicator light comes on when the ESC is turned off with the button.
When should ESC be turned on?
ESC should be turned on for daily driving whenever possible.
How do you turn ESC off while driving?
To turn ESC off while driving, press the ESC OFF button while driving on a flat road surface.
What should you do when operating the vehicle on a dynamometer?
When operating the vehicle on a dynamometer, ensure that the ESC is turned off (ESC OFF light illuminated). If the ESC is left on, it may prevent the vehicle speed from increasing, and result in false diagnosis.
Does turning the ESC off affect the ABS or brake system operation?
Turning the ESC off does not affect ABS or brake system operation.
What is a warning about operating ESC?
Never press the ESC OFF button while ESC is operating (ESC indicator light blinks). If ESC is turned off while ESC is operating, the vehicle may slip out of control.
What is a warning about Electronic stability control?
Drive carefully even though your vehicle has Electronic Stability Control. It can only assist you in maintaining control under certain circumstances.
What does the Vehicle Stability Management (VSM) system do?
This system provides further enhancements to vehicle stability and steering responses when a vehicle is driving on a slippery road or a vehicle detects changes in coefficient of friction between right wheels and left wheels when braking.
How do you know when the VSM is in operation?
When the VSM is in operation, ESC indicator light blinks. When the vehicle stability management is operating properly, you can feel a slight pulsation in the vehicle and/or abnormal steering responses (EPS- Electronic Power Steering). This is only the effect of brake and EPS control and indicates nothing unusual.
When does the VSM not operate?
The VSM does not operate when: Driving on a sloping road such as a gradient or incline, driving in reverse, the ESC OFF indicator light remains on the instrument cluster or the EPS indicator light remains on the instrument cluster.
How do you turn off the VSM?
If you press the ESC OFF button to turn off the ESC, the VSM will also cancel and the ESC OFF indicator light illuminates.
How do you turn on the VSM?
To turn on the VSM, press the button again. The ESC OFF indicator light goes out.
What should you make sure of when replacing tires and wheels?
When replacing tires and wheels, make sure they are the same size as the original tires and wheels installed. Driving with varying tire or wheel sizes may diminish any supplemental safety benefits of the VSM system.
What does it mean if the VSM is deactivated without pressing the ESC OFF button?
The VSM can be deactivated even if you don’t cancel the VSM operation by pressing the ESC OFF button. It indicates that a malfunction has been detected somewhere in the Electric Power Steering system or VSM system.
What should you do if the ESC indicator light or EPS warning light remains on?
If the ESC indicator light or EPS warning light remains on, take your vehicle to an authorized Kia dealer and have the system checked.
At what speeds is the VSM designed to function on curves?
The VSM is designed to function above approximately 13 mph (22 km/h) on curves.
At what speeds is the VSM designed to function when braking on a split-mu surface?
The VSM is designed to function above approximately 6 mph (10 km/h) when a vehicle is braking on a split-mu surface. A split-mu surface is made of two surfaces which have different friction forces.
What is a caution about the Vehicle Stability Management system?
The Vehicle Stability Management system is not a substitute for safe driving practices but a supplementary function only. It is the responsibility of the driver to always check the speed and the distance to the vehicle ahead. Always hold the steering wheel firmly while driving.
What should you always follow, even with VSM installed?
Your vehicle is designed to activate according to the driver’s intention, even with installed VSM. Always follow all the normal precautions for driving at safe speeds for the conditions – including driving in clement weather and on a slippery road.
What is the most important thing to do for maximum protection while driving?
For maximum protection, always wear your seat belt. No system, no matter how advanced, can compensate for all driver error and/or driving conditions. Always drive responsibly.
How does the Hill-start Assist Control (HAC) work?
The Hill-start Assist Control (HAC) prevents the vehicle from rolling back by applying the brakes automatically for about 2 seconds. The brakes are released when the accelerator pedal is depressed or after about 2 seconds. The HAC is activated only for about 2 seconds, so when the vehicle is starting off always depress the accelerator pedal.
What is a warning about maintaining brake pressure on an incline?
HAC does not replace the need to apply brakes while stopped on an incline. While stopped, make sure you maintain brake pressure sufficient to prevent your vehicle from rolling backward and causing an accident. Don’t release the brake pedal until you are ready to accelerate forward.
When does the Blind Spot Detection System (BSD) activate?
The system activates when the vehicle speed exceeds 20 mph (32 km/h).
How do you turn on the Blind Spot Detection System (BSD)?
The indicator on the switch will illuminate when the Blind Spot Detection System (BSD) switch is pressed with the Engine Start/Stop Button ON.
How do you turn off the Blind Spot Detection System (BSD)?
Press the switch again, and the switch indicator and system will be turned off.
What happens to the Blind Spot Detection System (BSD) settings when the vehicle is turned off?
The system will remember the last settings upon restart.
What happens when the Blind Spot Detection System (BSD) is turned on?
When the system is turned on the warning light will illuminate for 3 seconds on the outside rearview mirror.
When will the Blind Spot Detection System (BSD) activate?
The system will activate when: 1. The system is on. 2. Vehicle speed is above 20 mph (32 km/h). 3. Other vehicles are detected in the rear side.
What should you always do when changing lanes?
Always drive safely and use caution when changing lanes.
When will a warning light illuminate on the outside rearview mirror?
If a vehicle is detected within the boundary of the system, a warning light will illuminate on the outside rearview mirror.
When will the second stage alarm activate?
The second stage alarm will activate when: 1. The first stage alert is on 2. The turn signal is on to change a lane.
What happens when the second stage alert is activated?
When the second stage alert is activated, a warning light will blink on the outside rearview mirror and an alarm will sound.
How do you deactivate the second stage alert?
If you move the turn signal switch to the original position, the second stage alert will be deactivated.
How do you activate the second stage alarm sound?
Go to the User Settings Mode → Sound and select “BSD” on the LCD display.
How do you deactivate the second stage alarm sound?
Go to the User Settings Mode → Sound and deselect “BSD” on the LCD display.
Where are the sensors located for the Blind Spot Detection System (BSD)?
The sensors are located inside of the rear bumper.
Why is it important to keep the rear bumper clean?
Always keep the rear bumper clean for the system to work properly.
When may a warning message appear for the Blind Spot Detection System (BSD)?
This warning message may appear when:
- There are foreign substances on the rear bumper or inside the rear bumper.
- The vehicle carries a trailer or carrier on the rear.
- Driving in rural areas with little traffic or open terrains such as a wide expanse of desert.
- There is heavy snow or rain.
What should you do if you are carrying a trailer or carrier on the rear of the vehicle?
Turn off the BSD.
What happens when you turn off the BSD?
The light on the switch and the system will turn off automatically.
How long does it take for the Blind Spot Detection System (BSD) to work normally after removing a foreign substance?
After the foreign substance is removed, if you drive for approximately 10 minutes, the system will work normally.
What should you do if the Blind Spot Detection System (BSD) does not operate normally after removing a foreign substance, or if it is not one of the situations previously mentioned?
We recommend that you take your vehicle to an authorized Kia dealer and have the system checked.
What happens if the Blind Spot Detection System (BSD) does not work properly?
If the system does not work properly, a warning message will appear and the light on the switch will turn off. The system will turn off automatically.
What should you do if the Blind Spot Detection System (BSD) does not work properly?
Have your vehicle inspected by an authorized Kia dealer.
What is the Rear Cross Traffic Alert (RCTA) system?
When your vehicle moves backwards from a parking position, the sensor detects approaching vehicles to the left or right side direction and gives information to the driver.
How do you turn on the Rear Cross Traffic Alert (RCTA) system?
Select RCTA (Rear Cross Traffic Alert) in “User Settings” under “Driving Assist” on the instrument cluster.
How do you turn off the Rear Cross Traffic Alert (RCTA) system?
Select RCTA again, to turn the system off.
What happens to the Rear Cross Traffic Alert (RCTA) system when the vehicle is turned off?
The RCTA system will remember the last settings upon restart.
When does the Rear Cross Traffic Alert (RCTA) system operate?
The system operates when the vehicle speed is below 7 mph (11 km/h) with the shift lever in R (Reverse).
What is the detecting range for the Rear Cross Traffic Alert (RCTA) system?
The RCTA (Rear Cross Traffic Alert) detecting range is 1.6 feet ~ 65 feet based on the side direction.
What is the speed range for the Rear Cross Traffic Alert (RCTA) system to detect an approaching vehicle?
If the approaching vehicle speed is 2.5 mph (4 km/h) ~ 22 mph (36 km/h) within sensing range, it is detected.
What happens when the Rear Cross Traffic Alert (RCTA) system detects a vehicle?
If the vehicle detected by sensors approaches your vehicle, the warning chime will sound and the warning light will blink on the outside rearview mirror.
What should you do if the detected object is not in your way when using the Rear Cross Traffic Alert (RCTA) system?
Move the vehicle away from the detected object slowly; and the warning will cancel once the object has been safely cleared.
What can cause the Rear Cross Traffic Alert (RCTA) system to not operate properly?
The system may not operate properly due to other factors or circumstances.
What can deteriorate the Rear Cross Traffic Alert (RCTA) system’s sensing ability?
If your vehicle’s left or right side bumper is blinded by a barrier or vehicles, the system sensing ability may be deteriorated.
When might the Rear Cross Traffic Alert (RCTA) system not work properly?
The system may not work properly if the bumper has been replaced or if repair work has been done near the sensor.
How does the road width affect the Rear Cross Traffic Alert (RCTA) system?
The detection area differs according to the road’s width. If the road is narrow the system may detect other vehicles in the next lane. If the road is very wide the system may not detect other vehicles.
What can cause the Rear Cross Traffic Alert (RCTA) system to turn off?
The system may turn off due to strong electromagnetic interference.
When should the driver be cautious because the system may not assist the driver or work properly?
- Curved roads, tollgates, etc.
- The surrounding of the sensor cover is dirty with rain, snow, mud, etc.
- The rear bumper near the sensor is covered or obstructed with foreign matter such as a sticker, bumper guard, bicycle racks, etc.
- The rear bumper is damaged or the sensor is out of place.
- The height of the vehicle has significantly changed such as when the trunk is loaded with heavy objects, abnormal tire pressure etc.
- Due to bad weather such as heavy rain or snow.
- A fixed object is near such as a guardrail, etc.
- A substantial amount of metallic objects such as a construction area.
- A large vehicle is nearby such as a bus or truck.
- A motorcycle or bicycle is near.
- A flat trailer is near.
- If two vehicles near each other accelerate together.
- When another vehicle passes by at a high rate of speed.
- When changing lanes.
- When going down or up a steep, uneven road.
- When another vehicle drives very close to the back bumper/trunk.
- When a trailer or carrier is installed.
- When the temperature of the rear bumper is very high or low.
- When bike racks, etc. cover the sensor.
- When reversing from a parking space with pillars or metal structures.
- When you are reversing and if the detected vehicle is simultaneously reversing.
- If there are small objects like shopping carts and baby carriages.
- If there is a vehicle with decreased ride height (lowered).
- When the vehicle is close to another vehicle.
- When driving through a narrow road with many plants.
- When driving on a wet surface.
What can cause the outside rearview mirror to not alert the driver?
- The outside rearview mirror housing is very dirty.
- The window is very dirty.
- The windows are tinted very dark.
What is the Lane Departure Warning System (LDWS)?
This system detects the lane with a sensor at the front windshield and notifies you if it detects that your vehicle leaves the lane.
Does the Lane Departure Warning System (LDWS) make the vehicle change lanes?
The LDWS does not make the vehicle change lanes.
What is the driver’s responsibility when using the Lane Departure Warning System (LDWS)?
It is the driver’s responsibility to always check the road conditions.
When will the Lane Departure Warning System (LDWS) not notify you if the vehicle leaves the lane?
If the sensor cannot detect the lane or if the vehicle speed does not exceed 40 mph (64 kph), the LDWS will not be able to notify you if the vehicle leaves the lane.
What can affect the Lane Departure Warning System (LDWS)?
If your vehicle has window tint or other types of coating on the front windshield, the LDWS may not work properly.
What should you do to protect the Lane Departure Warning System (LDWS) sensor?
Prevent damage to the LDWS sensor from water or any liquid. Do not remove the LDWS parts and avoid damaging the sensor by avoiding strong impacts. Do not put objects that reflect light on the dash board.
What can affect the operation of the Lane Departure Warning System (LDWS)?
The operation of the LDWS can be affected by several factors (including environmental conditions).
What is the driver’s responsibility when using the Lane Departure Warning System (LDWS)?
It is the responsibility of the driver to pay attention to the roadway and to maintain the vehicle in its lane at all times.
What should you do upon receiving an LDWS alert?
Upon receiving an LDWS alert, you must take the necessary steps to maintain control of your vehicle.
What does the Lane Departure Warning System (LDWS) not provide?
The LDWS does not provide any steering inputs into the vehicle for you.
What can happen if you make a large sudden steering input in response to an LDWS alert?
It can be dangerous to make a large sudden steering input in response to an alert, since that could result in loss of control.
How do you turn on the Lane Departure Warning System (LDWS)?
To operate the LDWS, press the button with the engine start/stop button in the ON position. The indicator illuminates white on the cluster.
How do you cancel the Lane Departure Warning System (LDWS)?
To cancel the LDWS, press the LDWS button again. The indicator on the cluster will go off.
When does the Lane Departure Warning System (LDWS) warning activate?
If the system detects that your vehicle is leaving the lane when the LDWS is operating and vehicle speed exceeds 40 mph (64 kph), the warning operates.
What are the Lane Departure Warning System (LDWS) warnings?
- Visual warning: If you leave a lane, the lane you cross will blink (yellow) and LDWS indicator will blink green on LCD during max 3 seconds.
- Auditory warning: If you leave the lane, the warning sound operates for maximum 3 seconds.
What does the white color of the Lane Departure Warning System (LDWS) symbol mean?
When you activate the lane departure warning system by pressing the LDWS button, system operating conditions are not satisfied or the sensor does not detect the lane line.
What does the green color of the Lane Departure Warning System (LDWS) symbol mean?
When you activate the lane departure warning system by pressing the LDWS button, system operating conditions are satisfied and the sensor detects the lane line.
What does the yellow color of the Lane Departure Warning System (LDWS) symbol mean?
When there is a malfunction with the lane departure warning system.
What happens when the Lane Departure Warning System (LDWS) is not working properly?
When the LDWS is not working properly, the warning light will illuminate and the warning message will come on for a few seconds. After the message disappears, the master warning light will illuminate.
What should you do if the Lane Departure Warning System (LDWS) is not working properly?
Take your vehicle to an authorized Kia dealer and have the system checked.
What conditions cause the Lane Departure Warning System (LDWS) not to operate?
- The driver turns on the turn signal or the hazard warning flasher to change lanes.
- Driving on the lane line.
What should you do to change lanes?
Operate the turn signal switch then change the lane.
What are conditions that cause missed warnings and false warnings for the Lane Departure Warning System (LDWS)?
- The lane is not visible due to snow, rain, debris, puddles or other environmental conditions.
- The brightness outside changes suddenly such as when entering/exiting a tunnel.
- The headlights are off at night or the vehicle is in a tunnel.
- The color of the lane marking from the road is difficult to distinguish.
- Driving on a steep grade or a curve.
- Light such as street lights, sunlight or oncoming vehicle lights reflect off of water on the road.
- The lens or windshield is obscured by debris.
- The sensor cannot detect the lane because of fog, heavy rain or heavy snow.
- The rear view mirror housing has overheated from exposure to direct sunlight.
- The lane is very wide or narrow.
- The lane line is damaged or indistinct.
- The windshield is fogged up by humidity.
- Objects in the median or along the side of the road cast shadows over the lane markings.
- The sensor cannot distinguish the lane from the road due to the dust/dirt.
- There are other markings similar to lane lines.
- There are lane boundaries instead of markings.
- The vehicle ahead is very close, obscuring the view of the lane markings, or the vehicle ahead is driving over the lane markings.
- The vehicle vibrates heavily due to poor road conditions.
- The lanes are merging, expanding, or otherwise overlapping.
- Something reflective is placed on the dashboard.
How should you drive to be more fuel efficient?
- Drive smoothly. Accelerate at a moderate rate. Don’t make “jack-rabbit” starts or full-throttle shifts and maintain a steady cruising speed. Don’t race between stop-lights. Try to adjust your speed to the traffic so you don’t have to change speeds unnecessarily. Avoid heavy traffic whenever possible. Always maintain a safe distance from other vehicles so you can avoid unnecessary braking. This also reduces brake wear.
- Drive at a moderate speed. The faster you drive, the more fuel your vehicle uses. Driving at a moderate speed, especially on the highway, is one of the most effective ways to reduce fuel consumption.
- Don’t “ride” the brake pedal. This can increase fuel consumption and also increase wear on these components. In addition, driving with your foot resting on the brake pedal may cause the brakes to overheat, which reduces their effectiveness and may lead to more serious consequences.
- Take care of your tires. Keep them inflated to the recommended pressure. Incorrect inflation, either too much or too little, results in unnecessary tire wear. Check the tire pressures at least once a month.
- Be sure that the wheels are aligned correctly. Improper alignment can result from hitting curbs or driving too fast over irregular surfaces. Poor alignment causes faster tire wear and may also result in other problems as well as greater fuel consumption.
- Keep your vehicle in good condition. For better fuel economy and reduced maintenance costs, maintain your vehicle in accordance with the maintenance schedule. If you drive your vehicle in severe conditions, more frequent maintenance is required.
- Keep your vehicle clean. For maximum service, your vehicle should be kept clean and free of corrosive materials. It is especially important that mud, dirt, ice, etc. not be allowed to accumulate on the underside of the vehicle. This extra weight can result in increased fuel consumption and also contribute to corrosion.
- Travel lightly. Don’t carry unnecessary weight in your vehicle. Weight reduces fuel economy.
- Don’t let the engine idle longer than necessary. If you are waiting (and not in traffic), turn off your engine and restart only when you’re ready to go.
How long should you warm up your vehicle?
Your vehicle does not require extended warm-up. After the engine has started, allow the engine to run for 10 to 20 seconds prior to placing the vehicle in gear. In very cold weather, however, give your engine a slightly longer warm-up period.
What is “lugging” the engine?
Lugging is driving too slowly in a very high gear resulting in engine bucking. If this happens, shift to a lower gear.
What is “over-revving” the engine?
Over-revving is racing the engine beyond its safe limit. This can be avoided by shifting at the recommended speed.
How does using the air conditioner affect fuel economy?
The air conditioning system is operated by engine power so your fuel economy is reduced when you use it.
How do open windows at high speeds affect fuel economy?
Open windows at high speeds can reduce fuel economy.
How do crosswinds and headwinds affect fuel economy?
Fuel economy is less in crosswinds and headwinds. To help offset some of this loss, slow down when driving in these conditions.
What should you do if you encounter hazardous driving conditions?
- Drive cautiously and allow extra distance for braking.
- Avoid sudden braking or steering.
- When braking with non-ABS brakes pump the brake pedal with a light up-and-down motion until the vehicle is stopped.
- Do not pump the brake pedal on a vehicle equipped with ABS.
- If stalled in snow, mud, or sand, use the second gear. Accelerate slowly to avoid spinning the drive wheels.
- Use sand, rock salt, or other non-slip material under the drive wheels to provide traction when stalled in ice, snow, or mud.
What should you do to reduce the risk of a rollover?
If at all possible, avoid sharp turns or abrupt maneuvers, do not load your roof rack with heavy cargo, and never modify your vehicle in any way.
What type of tires should you use on your vehicle?
Do not use a size and type of tire and wheel that is different from the one that is originally installed on your vehicle. When replacing the tires, be sure to equip all four tires with the tire and wheel of the same size, type, tread, brand and load-carrying capacity.
What should you not do when driving on slippery surfaces with an automatic transaxle?
Do not downshift with an automatic transaxle while driving on slippery surfaces. The sudden change in tire speed could cause the tires to skid and result in an accident.
What should you do if your vehicle is stuck in snow, sand, or mud?
If it is necessary to rock the vehicle to free it from snow, sand, or mud, first turn the steering wheel right and left to clear the area around your front wheels. Then, shift back and forth between R (Reverse) and any forward gear in vehicles equipped with an Automatic Transaxle. Do not race the engine, and spin the wheels as little as possible. The ESC system should be turned OFF prior to rocking the vehicle.
What can prolonged rocking of the vehicle cause?
Prolonged rocking may cause engine overheating, transaxle damage or failure, and tire damage.
What can spinning the wheels at high speeds when the vehicle is stationary cause?
Spinning the wheels at high speeds when the vehicle is stationary could cause a tire to overheat which could result in tire damage that may injure bystanders.
What should you avoid doing when cornering?
Avoid braking or gear changing in corners, especially when roads are wet.
How should corners be taken?
Ideally, corners should always be taken under gentle acceleration.
What are some important tips to remember when driving at night?
- Slow down and keep more distance between you and other vehicles, as it may be more difficult to see at night, especially in areas where there may not be any street lights.
- Adjust your mirrors to reduce the glare from other driver’s headlights.
- Keep your headlights clean and properly aimed. (On vehicles not equipped with the automatic headlight aiming feature.) Dirty or improperly aimed headlights will make it much more difficult to see at night.
- Avoid staring directly at the headlights of oncoming vehicles. You could be temporarily blinded, and it will take several seconds for your eyes to readjust to the darkness.
What should you consider when driving in the rain?
- A heavy rainfall will make it harder to see and will increase the distance needed to stop your vehicle, so slow down.
- Keep your windshield wiping equipment in good shape. Replace your windshield wiper blades when they show signs of streaking or missing areas on the windshield.
- If your tires are not in good condition, making a quick stop on wet pavement can cause a skid and possibly lead to an accident. Be sure your tires are in good shape.
- Turn on your headlights to make it easier for others to see you.
- Driving too fast through large puddles can affect your brakes. If you must go through puddles, try to drive through them slowly.
- If you believe you may have gotten your brakes wet, apply them lightly while driving until normal braking operation returns.
What should you do when driving in flooded areas?
Avoid driving through flooded areas unless you are sure the water is no higher than the bottom of the wheel hub. Drive through any water slowly. Allow adequate stopping distance because brake performance may be affected. After driving through water, dry the brakes by gently applying them several times while the vehicle is moving slowly.
What should you do when driving off-road?
Drive carefully off-road because your vehicle may be damaged by rocks or roots of trees. Become familiar with the off-road conditions where you are going to drive before you begin driving.
What should you do with your tires before highway driving?
Adjust the tire inflation pressures to specification. Low tire inflation pressures will result in overheating and possible failure of the tires. Avoid using worn or damaged tires which may result in reduced traction or tire failure. Never exceed the maximum tire inflation pressure shown on the tires.
What should you always check on your tires before driving?
Always check the tires for proper inflation before driving.
What can underinflated or overinflated tires cause?
Underinflated or overinflated tires can cause poor handling, loss of vehicle control, and sudden tire failure leading to accidents, injuries, and even death.
What should you check when traveling at high speeds?
Do not forget to check both the engine coolant and engine oil.
What can a loose or damaged drive belt cause?
A loose or damaged drive belt may result in overheating of the engine.
What should you check before driving your vehicle?
Always check the tire tread before driving your vehicle.
What can worn-out tires cause?
Worn-out tires can result in loss of vehicle control.
What should you do with worn-out tires?
Worn-out tires should be replaced as soon as possible.
What should you do to minimize the problems of winter driving?
- To drive your vehicle in deep snow, it may be necessary to use snow tires or to install tire chains on your tires. If snow tires are needed, it is necessary to select tires equivalent in size and type of the original equipment tires.
- Furthermore, speeding, rapid acceleration, sudden brake applications, and sharp turns are potentially very hazardous practices. During deceleration, use engine braking to the fullest extent.
- Sudden brake applications on snowy or icy roads may cause skids to occur. You need to keep sufficient distance between the vehicle in operation in front of your vehicle. Also, apply the brake gently.
- It should be noted that installing tire chains on the tire will provide a greater driving force, but will not prevent side skids. Tire chains are not legal in all states. Check state laws before fitting tire chains.
What type of snow tires should you use?
If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as the original tires.
Where should you mount snow tires?
Mount snow tires on all four wheels to balance your vehicle’s handling in all weather conditions.
What should you keep in mind when using snow tires on dry roads?
Keep in mind that the traction provided by snow tires on dry roads may not be as high as your vehicle’s original equipment tires.
What should you do before installing studded tires?
Do not install studded tires without first checking local, state and municipal regulations for possible restrictions against their use.
What type of snow tires should you use?
Snow tires should be equivalent in size and type to the vehicle’s standard tires.
Why is it recommended to use snow tires instead of snow chains?
Since the sidewalls of radial tires are thinner, they can be damaged by mounting some types of snow chains on them. Therefore, the use of snow tires is recommended instead of snow chains.
Should you mount tire chains on vehicles equipped with aluminum wheels?
Do not mount tire chains on vehicles equipped with aluminum wheels; snow chains may cause damage to the wheels.
What type of snow chains should you use if you have to use them?
If snow chains must be used, use wire-type chains with a thickness of less than 0.59 in (15mm).
Where should you install tire chains?
When using tire chains, install tire chains only on the front tires.
What should you make sure of when installing snow chains?
Make sure the snow chains are SAE class “S” certified.
What should you do after driving a short distance after installing snow chains?
Always check chain installation for proper mounting after driving approximately 0.3 to 0.6 miles (0.5 to 1 km) to ensure safe mounting. Retighten or remount the chains if they are loose.
What should you do before installing snow chains?
When mounting snow chains, park the vehicle on level ground away from traffic. Turn on the vehicle Hazard Warning flashers and place a triangular emergency warning device behind the vehicle if available. Always place the vehicle in P (Park), apply the parking brake and turn off the engine before installing snow chains.
What should you make sure about the snow chains you are using?
Make sure the snow chains are the correct size and type for your tires.
What can incorrect snow chains cause?
Incorrect snow chains can cause damage to the vehicle body and suspension.
How can the use of tire chains affect vehicle handling?
The use of chains may adversely affect vehicle handling.
What speed should you not exceed when using tire chains?
Do not exceed 20 mph (30 km/h) or the chain manufacturer’s recommended speed limit, whichever is lower.
What driving conditions should you avoid when using tire chains?
Drive carefully and avoid bumps, holes, sharp turns, and other road hazards, which may cause the vehicle to bounce.
What should you avoid doing when braking with tire chains?
Avoid sharp turns or locked-wheel braking.
What type of coolant should you use in your vehicle?
Use high quality ethylene glycol coolant. It is the only type of coolant that should be used because it helps prevent corrosion in the cooling system, lubricates the water pump and prevents freezing.
When should you replace or replenish your coolant?
Be sure to replace or replenish your coolant in accordance with the maintenance schedule.
What should you do before winter regarding your vehicle’s coolant?
Before winter, have your coolant tested to assure that its freezing point is sufficient for the temperatures anticipated during the winter.
What should you do to prepare your battery for winter?
Visually inspect the battery and cables.
Who should check your battery level of charge?
The level of charge in your battery can be checked by an authorized Kia dealer or a service station.
What type of oil should you use in cold weather?
In some climates it is recommended that a lower viscosity “winter weight” oil be used during cold weather.
What should you do if you aren’t sure what weight oil you should use?
Consult an authorized Kia dealer.
What should you check regarding your spark plugs and ignition system?
Inspect your spark plugs and replace them if necessary. Also check all ignition wiring and components to be sure they are not cracked, worn or damaged in any way.
What can chains that are the wrong size or improperly installed damage?
Chains that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body and wheels.
What should you do if you hear chains hitting the vehicle?
Stop driving and retighten the chains any time you hear them hitting the vehicle.
How do you keep locks from freezing?
To keep the locks from freezing, squirt an approved de-icer fluid or glycerine into the key opening. If a lock is covered with ice, squirt it with an approved de-icing fluid to remove the ice. If the lock is frozen internally, you may be able to thaw it out by using a heated key.
How do you keep the water in the window washer system from freezing?
To keep the water in the window washer system from freezing, add an approved window washer anti-freeze solution in accordance with instructions on the container.
What should you not use in the window washer system?
Do not use engine coolant or other types of anti-freeze as these may damage the paint finish.
How can you prevent your parking brake from freezing?
Under some conditions your parking brake can freeze in the engaged position. If there is a risk the parking brake may freeze, apply it only temporarily while you put the gear shift lever in P (Park, Automatic Transaxle) and block the rear wheels so the vehicle cannot roll. Then release the parking brake.
What should you periodically check underneath the vehicle for?
Under some conditions, snow and ice can build up under the fenders and interfere with the steering. When driving in severe winter conditions where this may happen, you should periodically check underneath the vehicle to be sure the movement of the front wheels and the steering components are not obstructed.
What should you do before towing a trailer?
If you are considering towing with your vehicle, you should first check with your country’s Department of Motor Vehicles to determine their legal requirements.
What may you need to install a trailer hitch?
You may require an additional wiring harness connector to install a trailer hitch.
What should you remember when trailering?
Remember that trailering is different than just driving your vehicle by itself. Trailering means changes in handling, durability, and fuel economy. Successful, safe trailering requires correct equipment, and it has to be used properly.
What are load-pulling components forced to do when trailering?
Load-pulling components such as the engine, transaxle, wheel assemblies, and tires are forced to work harder against the load of the added weight.
What should you do if you are pulling a trailer improperly?
Pulling a trailer improperly can damage your vehicle and result in costly repairs not covered by your warranty.
What should you always check before using your towing equipment?
Always check your towing equipment to confirm correct equipment size and installation before use.
What should you make sure of before towing?
Before towing, make sure the total trailer weight, GCW (gross combination weight), GVW (gross vehicle weight), GAW (gross axle weight) and trailer tongue load are all within the limits.
What should you consider when installing a trailer hitch?
- Will you have to make any holes in the body of your vehicle when you install a trailer hitch? If you do, then be sure to seal the holes later when you remove the hitch. If you don’t seal them, deadly carbon monoxide (CO) from your exhaust can get into your vehicle, as well as dirt and water.
- The bumpers on your vehicle are not intended for hitches. Do not attach rental hitches or other bumper-type hitches to them. Use only a frame-mounted hitch that does not attach to the bumper.
Where can you get a Kia trailer hitch accessory?
Kia trailer hitch accessory is available at an authorized Kia dealer.
How should you attach safety chains?
You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer so that the tongue will not drop to the road if it becomes separated from the hitch. Always leave just enough slack so you can turn with your trailer. And, never allow safety chains to drag on the ground.
What should you do if your trailer is equipped with a braking system?
If your trailer is equipped with a braking system, make sure it conforms to your state’s regulations and that it is properly installed and operating correctly.
When is your trailer required to have its own brakes?
If your trailer weight exceeds the maximum allowed weight without trailer brakes, then the trailer will also require its own brakes as well.
What should I do if I have a flat tire (with spare tire, if equipped)?
The jack and wheel lug nut wrench are stored in the luggage compartment. Remove the panel indicated in the illustration. The jack is provided for emergency tire changing only. To prevent the jack from “rattling” while the vehicle is in motion, store it properly. Follow jacking instructions to reduce the possibility of personal injury. Always move the vehicle completely off the road and onto the shoulder before trying to change a tire. The jack should be used on firm level ground. If you cannot find a firm, level place off the road, call a towing service company for assistance.
What should I never use for jack support?
Never use the bumpers or any other part of the vehicle for jack support.
What should I do to make sure the vehicle does not roll off of the jack?
Do not place any portion of your body under a vehicle that is only supported by a jack since the vehicle can easily roll off the jack. Use vehicle support stands.
How do I remove and store the spare tire?
Turn the tire hold-down wing bolt counterclockwise. Store the tire in the reverse order of removal. To prevent the spare tire and tools from “rattling” while the vehicle is in motion, store them properly.
How can I loosen the tire hold-down wing bolt if it is hard to loosen by hand?
Put the jack handle inside of the tire hold-down wing bolt and turn the tire hold-down wing bolt counterclockwise with the jack handle.
What should I not do while the vehicle is on the jack?
Do not start or run the engine of the vehicle while the vehicle is on the jack as this may cause the vehicle to fall off the jack.
What are the steps for changing a tire?
- Park on a level surface and apply the parking brake firmly.
- Place the transaxle shift lever in P (Park) with automatic transaxle.
- Activate the hazard warning flashers.
- Remove the wheel lug nut wrench, jack and spare tire from the vehicle.
- Block both the front and rear of the wheel that is diagonally opposite from the jack position.
- Loosen the wheel lug nuts counterclockwise one turn each, but do not remove any nut until the tire has been raised off the ground.
- Place the jack at the front or rear jacking position closest to the tire you are changing. Place the jack at the designated locations under the frame.
- Insert the wheel lug nut wrench into the jack and turn it clockwise, raising the vehicle until the tire just clears the ground.
- Loosen the wheel nuts and remove them with your fingers.
- Slide the wheel off the studs and lay it flat so it cannot roll away.
- Pick up the spare tire, line up the holes with the studs and slide the wheel onto them.
- Hold it on the studs, put the wheel nuts on the studs and tighten them finger tight.
- Jiggle the tire to be sure it is completely seated, then tighten the nuts as much as possible with your fingers again.
- Insert the wrench into the jack and lower the vehicle to the ground by turning the wheel nut wrench counterclockwise.
- Tighten every nut following the numerical sequence shown in the image until they are all tight. Double-check each nut for tightness.
- After changing wheels, have an authorized Kia dealer tighten the wheel nuts to their proper torque as soon as possible.
What is the wheel nut tightening torque?
79 ~ 94 lb·ft (11 ~ 13 kg·m).
What should I do after changing the wheels?
Always secure the flat tire in its place and return the jack and tools to their proper storage locations.
What should I do if I have a tire gauge after changing a tire?
Remove the valve cap and check the air pressure. If the pressure is lower than recommended, drive slowly to the nearest service station and inflate to the correct pressure. If it is too high, adjust it until it is correct. Always reinstall the valve cap after checking or adjusting the tire pressure. If the cap is not replaced, dust and dirt may get into the tire valve and air may leak from the tire. If you lose a valve cap, buy another and install it as soon as possible.
What kind of threads do lug nuts have?
Your vehicle has metric threads on the wheel studs and nuts.
What should I do to make sure I’m using the correct lug nuts?
Make certain during wheel removal that the same nuts that were removed are reinstalled -or, if replaced, that nuts with metric threads and the same chamfer configuration are used.
What can happen if I install a non-metric thread nut on a metric stud?
Installation of a non-metric thread nut on a metric stud will not secure the wheel to the hub properly and will damage the stud so that it must be replaced.
What should I check after installing the spare tire?
Check the inflation pressures as soon as possible after installing the spare tire. Adjust it to the specified pressure, if necessary.
What kind of spare tire is in the vehicle?
Your vehicle is equipped with a compact spare tire. This compact spare tire takes up less space than a regular-size tire. This tire is smaller than a conventional tire and is designed for temporary use only.
What should I do when the compact spare is in use?
You should drive carefully when the compact spare is in use. The compact spare should be replaced by the proper conventional tire and rim at the first opportunity. The operation of this vehicle is not recommended with more than one compact spare tire in use at the same time.
What is the recommended inflation for the compact spare tire?
The compact spare should be inflated to 60 psi (420 kPa).
What speed should I not exceed when operating the vehicle with the compact spare?
Do not operate your vehicle on this compact spare at speeds over 50 mph (80 km/h).
What should I do with the original tire as soon as possible?
The original tire should be repaired or replaced as soon as possible to avoid failure of the spare possibly leading to personal injury or death.
What can happen if the studs are damaged?
If the studs are damaged, they may lose their ability to retain the wheel. This could lead to the loss of the wheel and a collision resulting in serious injuries.
What precautions should I take when using a compact spare tire?
- Under no circumstances should you exceed 50 mph (80 km/h); a higher speed could damage the tire.
- Ensure that you drive slowly enough for the road conditions to avoid all hazards. Any road hazard, such as a pothole or debris, could seriously damage the compact spare.
- Any continuous road use of this tire could result in tire failure, loss of vehicle control, and possible personal injury.
- Do not exceed the vehicle’s maximum load rating or the load-carrying capacity shown on the sidewall of the compact spare tire.
- Avoid driving over obstacles. The compact spare tire diameter is smaller than the diameter of a conventional tire and reduces the ground clearance approximately 1 inch (25 mm), which could result in damage to the vehicle.
- Do not take this vehicle through an automatic vehicle wash while the compact spare tire is installed.
- Do not use tire chains on the compact spare tire. Because of the smaller size, a tire chain will not fit properly. This could damage the vehicle and result in loss of the chain.
- Do not use the compact spare tire on any other vehicle because this tire has been designed especially for your vehicle.
- The compact spare tire’s tread life is shorter than a regular tire. Inspect your compact spare tire regularly and replace worn compact spare tires with the same size and design, mounted on the same wheel.
- The compact spare tire should not be used on any other wheels, nor should standard tires, snow tires, wheel covers or trim rings be used with the compact spare wheel.
- Do not use more than one compact spare tire at a time.
- Do not tow a trailer while the compact spare tire is installed.
What are some important things to know about the jack?
- When using the jack, set your parking brake.
- When using the jack, stop the engine.
- Do not get under a vehicle that is supported by a jack.
- The jack should be used on firm level ground.
- When supporting the vehicle, the base plate of jack must be vertical under the lifting point.
- Move the shift lever to the P position on vehicles with automatic transmission.
What is the tire mobility kit?
The Tire Mobility Kit is a temporary fix to the tire and the tire should be inspected by an authorized Kia dealer as soon as possible.
When should I not use the tire mobility kit?
When two or more tires are flat, do not use the tire mobility kit. The Tire Mobility Kit supports only enough sealant for one flat tire.
What should I do after using the tire mobility kit?
Have your tire repaired as soon as possible. The tire may lose air pressure at any time after inflating with the Tire Mobility Kit.
What does the Tire Mobility Kit do?
The system of compressor and sealing compound effectively and comfortably seals most punctures in a passenger car tire caused by nails or similar objects and reinflates the tire. After you ensured that the tire is properly sealed you can drive cautiously on the tire (up to 120 miles (200 km)) at a max. speed of 50 mph (80 km/h) in order to reach a service station or tire dealer to have the tire replacement.
What kind of tire punctures can’t be repaired with the tire mobility kit?
Do not use the Tire Mobility Kit to repair punctures in the tire walls. This can result in an accident due to tire failure.
What should I do if the tire cannot be sealed completely by the tire mobility kit?
Avoid abrupt steering or other driving maneuvers, especially if the vehicle is heavily loaded or if a trailer is in use.
Is the tire mobility kit a permanent tire repair method?
The Tire Mobility Kit is not designed or intended as a permanent tire repair method and is to be used for one tire only.
What are the notes on the safe use of the tire mobility kit?
- Park your car at the side of the road so that you can work with the Tire Mobility Kit away from moving traffic.
- To be sure your vehicle will not move, even when you’re on fairly level ground, always set your parking brake.
- Only use the Tire Mobility Kit for sealing/inflation passenger car tires.
- Only punctured areas located within the tread region of the tire can be sealed using the tire mobility kit.
- Do not use on motorcycles, bicycles or any other type of tires.
- When the tire and wheel are damaged, do not use Tire Mobility Kit for your safety.
- Use of the Tire Mobility Kit may not be effective for tire damage larger than approximately 0.24 in (6 mm). Please contact the nearest Kia dealership if the tire cannot be made roadworthy with the Tire Mobility Kit.
What should I do after repairing the tire with the Tire Mobility Kit?
Carefully remove any extra sealant applied on the tire air pressure sensor and wheel.
What should I avoid using when repairing the tire?
Do not use an aftermarket tire repair kit (including sealant). The aftermarket sealant may lead to malfunction of the tire air pressure sensor.
What are the components of the Tire Mobility Kit?
- Speed restriction label
- Sealant bottle and label with speed restriction
- Filling hose from sealant bottle to wheel
- Connectors and cable for the power outlet direct connection
- Holder for the sealant bottle
- Compressor
- On/off switch
- Pressure gauge for displaying the tire inflation pressure
- Button for reducing tire inflation pressure
- Hose to connect compressor and sealant bottle or compressor and wheel
What should I do before using the tire mobility kit?
Detach the speed restriction label from the sealant bottle and place it in a highly visible place inside the vehicle such as on the steering wheel to remind the driver not to drive too fast.
What are the steps for using the Tire Mobility Kit?
- Thoroughly shake the sealant bottle.
- Screw connection hose onto the connector of the sealant bottle.
- Ensure that button on the compressor is not pressed.
- Unscrew the valve stem cap from the flat tire and screw the filling hose of the sealant bottle onto the valve stem.
- Insert the sealant bottle into the housing of the compressor so that the bottle is upright.
- Ensure that the compressor is switched off, position 0.
- Connect between compressor and the vehicle power outlet using the cable and connectors.
- With the engine start/stop button position on or ignition switch position on, switch on the compressor and let it run for approximately 5~7 minutes to fill the sealant up to proper pressure.
- Switch off the compressor.
- Detach the hoses from the sealant bottle connector and from the tire valve stem.
- Return the Tire Mobility Kit to its storage location in the vehicle.
- Immediately drive approximately 4~6 miles (7~10 km or, about 10 min) to evenly distribute the sealant in the tire.
- After driving approximately 4 ~ 6 miles (7 ~ 10 km or about 10 min), stop at a safe location.
- Screw the connection hose of the compressor to the valve stem.
- Plug the compressor power cord into the vehicle power outlet.
- Adjust the tire inflation pressure to the recommended tire inflation.
What is important to know about the sealant?
- Keep out of reach of children.
- Avoid contact with eyes.
- Do not swallow.
- Do not use the Tire sealant after the sealant has expired.
What can happen if the sealant is applied when the valve is incompletely connected?
The sealant may backdraft and result in valve clogging.
What should I do if a visible foreign object has punctured the tire?
Do not remove it before using Tire Mobility Kit.
What can happen if the engine is left running in a poorly ventilated area?
Carbon monoxide poisoning and suffocation is possible if the engine is left running in a poorly ventilated or unventilated location (such as inside a building).
What should I do if the tire pressure is below 29 psi (200kPa)?
Do not attempt to drive your vehicle if the tire pressure is below 29 psi (200kPa). This could result in an accident due to sudden tire failure.
How do I increase the inflation pressure?
Switch on the compressor, position I.
How do I reduce the inflation pressure?
Press the button on the compressor.
What is the system voltage of the Tire Mobility Kit?
DC 12 V.
What is the working voltage of the Tire Mobility Kit?
DC 10 – 15 V.
What is the amperage rating of the Tire Mobility Kit?
max.15 A.
What temperatures is the Tire Mobility Kit suitable for use at?
-22 ~ +158°F (-30 ~ +70°C).
What is the max. working pressure of the Tire Mobility Kit?
87 psi (6 bar).
What should I do if my tire pressure sensors are damaged by sealant?
The sealant on the tire pressure sensor and wheel should be removed when you replace the tire with a new one and inspect the tire pressure sensors at an authorized dealer.
What should I do if emergency towing is necessary?
We recommend having it done by an authorized Kia dealer or a commercial tow-truck service. Proper lifting and towing procedures are necessary to prevent damage to the vehicle. The use of wheel dollies or flatbed is recommended.
How should an AWD vehicle be towed?
Your vehicle must be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground.
How should an FWD vehicle be towed?
It is acceptable to tow the vehicle with the rear wheels on the ground (without dollies) and the front wheels off the ground. If any of the loaded wheels or suspension components are damaged or the vehicle is being towed with the front wheels on the ground, use a towing dolly under the front wheels. When being towed by a commercial tow truck and wheel dollies are not used, the front of the vehicle should always be lifted, not the rear.
What should the ignition switch be set to when being towed?
If your vehicle is equipped with side and curtain air bag, set the ignition switch to LOCK or ACC position when the vehicle is being towed.
Why should the ignition switch be set to LOCK or ACC when being towed?
The side and curtain air bag may deploy when the ignition is ON,and the rollover sensor detects the situation as a rollover.
How should an AWD vehicle not be towed?
The AWD vehicle should never be towed with the wheels on the ground. This can cause serious damage to the transaxle or the AWD system.
What steps should I take when towing my vehicle in an emergency without wheel dollies?
- Set the ignition switch in the ACC position.
- Place the transaxle shift lever in N (Neutral).
- Release the parking brake.
Where is the towing hook?
Open the tailgate, and remove the towing hook from the tool case.
How do I install the towing hook?
Install the towing hook by turning it clockwise into the hole until it is fully secured.
What should I do with the towing hook after use?
Remove the towing hook and install the cover after use.
What should I do if towing service is not available in an emergency?
Your vehicle may be temporarily towed using a cable or chain secured to the emergency towing hook under the front (or rear) of the vehicle. Use extreme caution when towing the vehicle. A driver must be in the vehicle to steer it and operate the brakes. Towing in this manner may be done only on hard-surfaced roads for a short distance and at low speed. Also, the wheels, axles, power train, steering and brakes must all be in good condition.
What should I not do with the tow hooks?
Do not use the tow hooks to pull a vehicle out of mud, sand or other conditions from which the vehicle cannot be driven out under its own power.
What should I avoid when towing a vehicle?
Avoid towing a vehicle heavier than the vehicle doing the towing.
What should the drivers of both vehicles do when towing?
The drivers of both vehicles should communicate with each other frequently.
What should I do when attaching a towing strap to the tow hook?
Use only a cable or chain specifically intended for use in towing vehicles. Securely fasten the cable or chain to the towing hook provided.
What should I check before emergency towing?
Before emergency towing, check if the hook is not broken or damaged.
How should I use the tow hook?
- Fasten the towing cable or chain securely to the hook.
- Do not jerk the hook. Apply it steadily and with even force.
- To avoid damaging the hook, do not pull from the side or at a vertical angle. Always pull straight ahead.
- Use a towing strap less than 16 feet (5 m) long. Attach a white or red cloth (about 12 inches (30 cm) wide) in the middle of the strap for easy visibility.
- Drive carefully so that the towing strap is not loosened during towing.
What should I not use for towing?
Using a portion of the vehicle other than the tow hooks for towing may damage the body of your vehicle.
What should I avoid doing when towing?
Avoid sudden starts or erratic driving maneuvers which would place excessive stress on the emergency towing hook and towing cable or chain.
What should I do if the disabled vehicle is unable to be moved?
If the disabled vehicle is unable to be moved, do not forcibly continue the towing. We recommend that you contact an authorized Kia dealer or a commercial tow truck service for assistance.
What should I do when towing the vehicle?
Tow the vehicle as straight ahead as possible.
What should I do to stay safe when towing?
Keep away from the vehicle during towing.
What should I do to prepare the car for emergency towing?
- Turn the ignition switch to ACC so the steering wheel isn’t locked.
- Place the transaxle shift lever in N (Neutral).
- Release the parking brake.
- Press the brake pedal with more force than normal since you will have reduced brake performance.
- More steering effort will be required because the power steering system will be disabled.
- If you are driving down a long hill, the brakes may overheat and brake performance will be reduced. Stop often and let the brakes cool off.
- If the car is being towed with all four wheels on the ground, it can be towed only from the front. Be sure that the transaxle is in neutral. Be sure the steering is unlocked by placing the ignition switch in the ACC position. A driver must be in the towed vehicle to operate the steering and brakes.
What are the automatic transaxle precautions when towing?
- To avoid serious damage to the automatic transaxle, limit the vehicle speed to 10 mph (15 km/h) and drive less than 1 mile (1.5 km) when towing.
- Before towing, check the automatic transaxle for fluid leaks under your vehicle. If the automatic transaxle fluid is leaking, flatbed equipment or a towing dolly must be used.
What should I check when stopping for fuel?
- Check the engine oil level.
- Check the coolant level in the coolant reservoir.
- Check the windshield washer fluid level.
- Look for low or under-inflated tires.
What should I check while operating my vehicle?
- Note any changes in the sound of the exhaust or any smell of exhaust fumes in the vehicle.
- Check for vibrations in the steering wheel.
- Notice any increased steering effort or looseness in the steering wheel, or change in its straight-ahead position.
- Notice if your vehicle constantly turns slightly or “pulls” to one side when traveling on smooth, level roads.
- When stopping, listen and check for unusual sounds, pulling to one side, increased brake pedal travel or “hard-to-push” brake pedal.
- If any slipping or changes in the operation of your transaxle occurs, check the transaxle fluid level.
- Check the automatic transaxle P (Park) function.
- Check the parking brake.
- Check for fluid leaks under your vehicle (water dripping from the air conditioning system during or after use is normal).
What should I do monthly?
- Check the coolant level in the engine coolant reservoir.
- Check the operation of all exterior lights, including the stoplights, turn signals and hazard warning flashers.
- Check the inflation pressures of all tires including the spare.
What should I do at least twice a year?
- Check the radiator, heater and air conditioning hoses for leaks or damage.
- Check the windshield washer spray and wiper operation. Clean the wiper blades with clean cloth dampened with washer fluid.
- Check the headlight alignment.
- Check the muffler, exhaust pipes, shields and clamps.
- Check the lap/shoulder belts for wear and function.
- Check for worn tires and loose wheel lug nuts.
What are the conditions for following the Maintenance Under Severe Usage Conditions?
- Repeated driving short distance of less than 5 miles (8 km) in normal temperature or less than 10 miles (16 km) in freezing temperature.
- Extensive engine idling or low speed driving for long distances.
- Driving on rough, dusty, muddy, unpaved, graveled or salt-spread roads.
- Driving in areas using salt or other corrosive materials or in very cold weather.
- Driving in heavy dust conditions.
- Driving in heavy traffic areas.
- Driving on uphill, downhill, or mountain roads repeatedly.
- Towing a trailer or using a camper, or roof rack.
- Driving as a patrol car, taxi, other commercial use of vehicle towing.
- Driving over 106 mile/h (170 km/h).
- Frequently driving in stop-and-go condition.
How often should I rotate tires?
Rotate tires every 7,500 miles (12,000 km).
When should I replace the climate control air filter?
The climate control air filter should be replaced every 12 months or 7,500 miles (12,000 km).
How often should I inspect the vacuum hose?
The vacuum hose should be inspected every 12 months or 7,500 miles (12,000 km).
When should I first replace the coolant?
At first, replace the coolant at 120,000 miles (200,000 km) or 10 years.
How often should I replace the coolant after the first time?
After that, replace the coolant every 30,000 miles (50,000 km) or 24 months.
How often should I inspect the battery condition?
The battery condition should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect brake lines, hoses and connections?
Brake lines, hoses and connections should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect disc brakes and pads?
Disc brakes and pads should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect steering gear rack, linkage and boots?
Steering gear rack, linkage and boots should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect driveshaft and boots?
Driveshaft and boots should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect suspension mounting bolts/ball joints?
Suspension mounting bolts should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect the air conditioner refrigerant?
The air conditioner refrigerant should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect the air conditioner compressor?
The air conditioner compressor should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect the propeller shaft?
The propeller shaft should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect the exhaust pipe and muffler?
The exhaust pipe and muffler should be inspected every 12 months or 7,500 miles (12,000 km).
How often should I inspect intercooler, in/out hose, air intake hose?
The intercooler, in/out hose, air intake hose should be inspected every 12 months or 6,000 miles (10,000 km) on Turbo models.
How often should I inspect the cooling system?
The cooling system should be inspected every 36 months or 18,000 miles (30,000 km) on Turbo models and every 24 months or 15,000 miles (24,000 km) on Non-Turbo models.
How often should I inspect differential oil (rear)?
The differential oil (rear) should be inspected every 40,000 miles (60,000 km) on Turbo models.
How often should I inspect transfer case oil (AWD)?
The transfer case oil (AWD) should be inspected every 40,000 miles (60,000 km) on Turbo models and Non-Turbo models.
How often should I inspect vapor hose, fuel filler cap and fuel tank?
The vapor hose, fuel filler cap and fuel tank should be inspected every 36 months or 18,000 miles (30,000 km) on Turbo models.
How often should I inspect the fuel tank air filter?
The fuel tank air filter should be inspected every 48 months or 24,000 miles (40,000 km) on Turbo models and every 36 months or 22,500 miles (36,000 km) on Non-Turbo models.
How often should I inspect fuel lines, hoses and connections?
Fuel lines, hoses and connections should be inspected every 36 months or 18,000 miles (30,000 km) on Turbo models and every 24 months or 15,000 miles (24,000 km) on Non-Turbo models.
How often should I inspect the parking brake?
The parking brake should be inspected every 24 months or 12,000 miles (20,000 km) on Turbo models and every 12 months or 7,500 miles (12,000 km) on Non-Turbo models.
How often should I inspect the brake fluid?
The brake fluid should be inspected every 24 months or 12,000 miles (20,000 km) on Turbo models and every 12 months or 7,500 miles (12,000 km) on Non-Turbo models.
What should be serviced more frequently on cars normally used under severe driving conditions?
- Engine oil and engine oil filter.
- Air cleaner filter.
- Spark plugs.
- Automatic transaxle fluid.
- Front brake disc/pads, calipers.
- Rear brake disc/pads.
- Parking brake.
- Steering gear box, linkage & boots/ Lower arm ball joint, upper arm ball joint.
- Drive shafts and boots.
- Differential oil (rear).
- Climate control air filter (for evaporator and blower unit).
- Propeller shaft.
- Transfer case oil (AWD).
How often should I replace the engine oil and filter under severe conditions for Turbo models?
Replace the engine oil and filter every 3,000 miles (5,000 km) or 3 months.
How often should I replace the automatic transaxle fluid under severe conditions for Turbo models?
Replace the automatic transaxle fluid every 60,000 miles (100,000 km).
How often should I replace the differential oil (rear) under severe conditions?
Replace the differential oil (rear) every 80,000 miles (120,000 km).
How often should I replace the transfer case oil (AWD) under severe conditions?
Replace the transfer case oil (AWD) every 80,000 miles (120,000 km).
How often should I replace the engine oil and filter under severe conditions for Non-Turbo models?
Replace the engine oil and filter every 3,750 miles (6,000 km) or 6 months.
How often should I replace the automatic transmission fluid under severe conditions for Non-Turbo models?
Replace the automatic transmission fluid every 60,000 miles (96,000 km).
How should you check the condition of the cooling system hoses and heater hoses?
Check the condition and connections of all cooling system hoses and heater hoses. Replace any swollen or deteriorated hoses.
How should you fill the coolant reservoir?
The coolant level should be filled between the MAX and MIN marks on the side of the coolant reservoir when the engine is cool.
What should you do if the coolant level is low?
If the coolant level is low, add enough specified coolant to provide protection against freezing and corrosion. Bring the level to MAX, but do not overfill.
What should you do if you need to add coolant frequently?
If frequent additions are required, see an authorized Kia dealer for a cooling system inspection.
What should you be cautious about when working near the cooling fan?
Use caution when working near the blade of the cooling fan. The electric motor (cooling fan) is controlled by engine coolant temperature, refrigerant pressure, and vehicle speed. It may sometimes operate even when the engine is not running.
What should you make sure of after refilling coolant?
Make sure the coolant cap is properly closed after refill of coolant. Otherwise, the engine could be overheated while driving.
How should you check if the radiator cap is correctly placed?
Check if the radiator cap label is straight in front. Make sure that the tiny protrusions inside the coolant cap should be securely interlocked.
What type of water should be used when adding coolant?
When adding coolant, use only deionized water or soft water for your vehicle and never mix hard water in the coolant filled at the factory.
What can happen if you use an improper coolant mixture?
An improper coolant mixture can result in serious malfunction or engine damage.
What type of coolant should be used in your vehicle?
The engine in your vehicle has aluminum engine parts and must be protected by an ethylene-glycol with phosphate-based coolant to prevent corrosion and freezing.
What type of coolants should you NOT use?
Do NOT use alcohol or methanol coolant or mix them with the specified coolant.
What are the recommended antifreeze percentages for different temperatures?
- 5°F (-15°C): 35% Antifreeze, 65% Water
- -13°F (-25°C): 40% Antifreeze, 60% Water
- -31°F (-35°C): 50% Antifreeze, 50% Water
- -49°F (-45°C): 60% Antifreeze, 40% Water
What should you do before refilling the coolant to prevent overflow?
Put a thick cloth or fabric around the radiator cap before refilling the coolant in order to prevent the coolant from overflowing into engine parts such as the generator.
How often should you have the coolant changed?
Have the coolant changed by an authorized Kia dealer according to the Maintenance Schedule.
How should you check the brake fluid level?
Check the fluid level in the reservoir periodically. The fluid level should be between MAX (Maximum) and MIN (Minimum) marks on the side of the reservoir.
What should you do before removing the brake fluid reservoir cap?
Before removing the reservoir cap and adding brake fluid, clean the area around the reservoir cap thoroughly to prevent brake fluid contamination.
What should you do if the brake fluid level is low?
If the level is low, add fluid to the MAX (Maximum) level.
What does it mean if the brake fluid level falls with accumulated mileage?
The level will fall with accumulated mileage. This is a normal condition associated with the wear of brake linings.
When should you have the brake system checked by an authorized Kia dealer?
If the fluid level is excessively low or if the brake system requires frequent additions of fluid, the vehicle should be inspected by an authorized Kia dealer.
What type of brake fluid should you use?
Use only the specified brake fluid.
Should you mix different types of brake fluid?
Never mix different types of fluid.
What should you do if brake fluid comes in contact with your eyes?
If brake fluid should come in contact with your eyes, immediately flush them with a large quantity of fresh tap water. Have your eyes examined by a doctor as soon as possible.
Should brake fluid exposed to open air be used?
Brake fluid, which has been exposed to open air for an extended time should never be used as its quality cannot be guaranteed.
What should you do with used brake fluid?
It should be disposed of properly.
What should you do to avoid paint damage from brake fluid?
Do not allow brake fluid to contact the vehicle’s body paint, as paint damage will result.
What fluids should you use in the brake system?
Only use brake fluid in the brake system.
What damage can occur if you use improper fluids (such as engine oil) in the brake system?
Small amounts of improper fluids (such as engine oil) can cause damage to the brake system.
How can you check the washer fluid level?
The reservoir is translucent so that you can check the level with a quick visual inspection.
What should you do if the washer fluid level is low?
Check the fluid level in the washer fluid reservoir and add fluid if necessary.
What can be used if washer fluid is not available?
Plain water may be used if washer fluid is not available.
What type of washer solvent should be used in cold climates?
Use washer solvent with antifreeze characteristics in cold climates to prevent freezing.
What should you be cautious of with washer fluid?
Do not allow the washer fluid to come in contact with open flames or sparks. The windshield washer fluid reservoir is flammable under certain circumstances. This can result in a fire.
Is it safe to drink windshield washer fluid?
Do not drink the windshield washer fluid. The windshield washer fluid is poisonous to humans and animals.
Can you use radiator coolant or antifreeze in the washer fluid reservoir?
Do not use radiator coolant or antifreeze in the washer fluid reservoir.
Why should you not use radiator coolant in the washer fluid reservoir?
Radiator coolant can severely obscure visibility when sprayed on the windshield and may cause loss of vehicle control.
How should you check the parking brake?
Check whether the stroke is within specification when the parking brake pedal is depressed with 44 lbs, 196 N (20 kg) of force. Also, the parking brake alone should securely hold the vehicle on a fairly steep grade.
What should you do if the parking brake stroke is not within specification?
If the stroke is more or less than specified, have the parking brake adjusted by an authorized Kia dealer.
What is the parking brake stroke specification?
Stroke : 4~5 notch
When should the air filter be replaced?
It must be replaced when necessary, and should not be washed.
How can you clean the air filter?
You can clean the filter when inspecting the air cleaner element. Clean the filter by using compressed air.
How should you replace the air cleaner filter?
- Pull out the air cleaner cover.
- Unlock by turning the locking lever downward.
- Pull the air cleaner filter to replace.
- Pull up the lever (1) to the LOCK position.
- Rise up the cover (2) until the hooks on the cover are securely fastened into the latches (3).
- Check if the cover is firmly installed.
When should you replace the air filter according to the maintenance schedule?
Replace the filter according to the Maintenance Schedule.
When should you replace the air filter more often than the usual recommended intervals?
If the vehicle is operated in extremely dusty or sandy areas, replace the element more often than the usual recommended intervals.
What can happen if you drive with the air cleaner removed?
Do not drive with the air cleaner removed; this will result in excessive engine wear.
What should you be careful of when removing the air cleaner filter?
When removing the air cleaner filter, be careful that dust or dirt does not enter the air intake, or damage may result.
What type of air filter should you use for replacement?
Use a Kia genuine part. Use of a non-genuine part could damage the air flow sensor.
When should the climate control air filter be replaced?
The climate control air filter should be replaced according to the Maintenance Schedule.
When should the climate control air filter be inspected and replaced more frequently?
If the vehicle is operated in severely air-polluted cities or on dusty rough roads for a long period, it should be inspected more frequently and replaced earlier.
How should you replace the climate control air filter?
- Open the glove box and remove the stoppers on both sides.
- With the glove box open, pull the support strap (1).
- Remove the climate control air filter cover while pressing the lock on the left side of the cover.
- Replace the climate control air filter.
- Reassemble in the reverse order of disassembly.
What can happen if the climate control air filter is not installed properly?
When replacing the climate control air filter install it properly. Otherwise, the system may produce noise and the effectiveness of the filter may be reduced.
What can make the windshield difficult to clean?
Commercial hot waxes applied by automatic car washes have been known to make the windshield difficult to clean.
What can reduce the effectiveness of the windshield wipers?
Contamination of either the windshield or the wiper blades with foreign matter can reduce the effectiveness of the windshield wipers. Common sources of contamination are insects, tree sap, and hot wax treatments used by some commercial car washes.
What should you do if the blades are not wiping properly?
If the blades are not wiping properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.
When should you replace the wiper blades?
When the wipers no longer clean adequately, the blades may be worn or cracked, and require replacement.
What should you NOT do when trying to clean or replace wiper blades?
To prevent damage to the wiper arms or other components, do not attempt to move the wipers manually.
What can happen if you use a non-specified wiper blade?
The use of a non-specified wiper blade could result in wiper malfunction and failure.
What should you NOT use on or near wiper blades?
To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.
How do you remove the front windshield wiper blade?
- Raise the wiper arm and turn the wiper blade assembly to expose the plastic locking clip.
- Compress the clip and slide the blade assembly downward.
- Lift it off the arm.
- Install the blade assembly in the reverse order of removal.
How do you remove the rear window wiper blade?
- Raise the wiper arm and pull out the wiper blade assembly.
What should you be careful of when handling the wiper arm?
Do not allow the wiper arm to fall against the windshield, since it may chip or crack the windshield.
How do you install the rear window wiper blade?
- Install the new blade assembly by inserting the center part into the slot in the wiper arm until it clicks into place.
- Make sure the blade assembly is installed firmly by trying to pull it slightly.
Who should replace the wiper blade to prevent damage?
To prevent damage to the wiper arms or other components, have an authorized Kia dealer replace the wiper blade.
What should you do to keep the battery in good condition?
- Keep the battery securely mounted.
- Keep the battery top clean and dry.
- Keep the terminals and connections clean, tight, and coated with petroleum jelly or terminal grease.
- Rinse any spilled electrolyte from the battery immediately with a solution of water and baking soda.
What should you do if the vehicle is not going to be used for an extended time?
If the vehicle is not going to be used for an extended time, disconnect the battery cables.
What should you do if electrolyte gets into your eyes?
If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immediate medical attention.
What should you do if electrolyte gets on your skin?
If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel pain or burning sensation, get medical attention immediately.
How should you dispose of a battery?
Dispose of the battery according to your local law(s) or regulation. Please return the battery to an authorized Kia dealer to be recycled.
Can you recharge the battery with the battery cables still connected?
Never attempt to recharge the battery when the battery cables are connected.
What are the risks when working with a battery?
Keep lit cigarettes and all other flames or sparks away from the battery. The battery contains hydrogen – a highly combustible gas which will explode if it comes in contact with a flame or spark.
Where should batteries be kept?
Keep batteries out of the reach of children because batteries contain highly corrosive SULFURIC ACID and electrolytes.
What should you do to protect yourself when working near a battery?
Wear eye protection when charging or working near a battery. Always provide ventilation when working in an enclosed space.
What can happen if you connect unauthorized electronic devices to the battery?
If you connect unauthorized electronic devices to the battery, the battery may be discharged. Never use unauthorized devices.
What type of battery does your vehicle have?
Your vehicle has a maintenance-free, calcium-based battery.
How should you recharge the battery if it becomes discharged in a short time?
If the battery becomes discharged in a short time, recharge it by slow charging (trickle) for 10 hours.
How should you recharge the battery if it gradually discharges because of high electric load?
If the battery gradually discharges because of high electric load while the vehicle is being used, recharge it at 20-30A for two hours.
What precautions should you observe when recharging the battery?
- The battery must be removed from the vehicle and placed in an area with good ventilation.
- Do not allow cigarettes, sparks, or flame near the battery.
- Watch the battery during charging, and stop or reduce the charging rate if the battery cells begin gassing (boiling) violently or if the temperature of the electrolyte of any cell exceeds 120°F (49°C).
- Wear eye protection when checking the battery during charging.
How should you disconnect the battery charger?
- Turn off the battery charger main switch.
- Unhook the negative clamp from the negative battery terminal.
- Unhook the positive clamp from the positive battery terminal.
What should you never touch while the vehicle is running?
Never touch the electrical ignition system while the vehicle is running. This system works with high voltage which can shock you.
What should you always do before performing maintenance or recharging the battery?
Before performing maintenance or recharging the battery, turn off all accessories and stop the engine.
Which battery cable should be removed first and installed last when the battery is disconnected?
The negative battery cable must be removed first and installed last when the battery is disconnected.
What items should be reset after the battery has been discharged or disconnected?
- Auto up/down window
- Sunroof
- Trip computer
- Climate control system
- Driver position memory system
- Audio
What must you always maintain for proper tire maintenance, safety, and maximum fuel economy?
You must always maintain recommended tire inflation pressures and stay within the load limits and weight distribution recommended for your vehicle.
When should you check tire pressures?
All tire pressures (including the spare) should be checked when the tires are cold.
What does “Cold Tires” mean?
“Cold Tires” means the vehicle has not been driven for at least three hours or driven less than one mile (1.6 km).
Where can you find the recommended inflation pressures?
For recommended inflation pressure refer to “Tire and wheels” in chapter 9. All specifications (sizes and pressures) can be found on a label attached to the driver’s side center pillar.
What are the risks of severe tire underinflation?
Severe underinflation (10 psi (70 kPa) or more) can lead to severe heat build-up, causing blowouts, tread separation, and other tire failures that can result in the loss of vehicle control. This risk is much higher on hot days and when driving for long periods at high speeds.
What does tire underinflation result in?
Underinflation also results in excessive wear, poor handling and reduced fuel economy. Wheel deformation is also possible.
What does tire overinflation produce?
Overinflation produces a harsh ride, excessive wear at the center of the tire tread, and a greater possibility of damage from road hazards.
How much do warm tires normally exceed recommended cold tire pressures?
Warm tires normally exceed recommended cold tire pressures by 4 to 6 psi (28 to 41 kPa).
Should you release air from warm tires to adjust the pressure?
Do not release air from warm tires to adjust the pressure or the tires will be underinflated.
Why should you reinstall tire inflation valve caps?
Be sure to reinstall the tire inflation valve caps. Without the valve cap, dirt or moisture could get into the valve core and cause air leakage.
What should you do if a valve cap is missing?
If a valve cap is missing, install a new one as soon as possible.
When should you check tire pressure?
- Check tire pressure when the tires are cold. (After the vehicle has been parked for at least three hours or hasn’t been driven more than one mile (1.6 km) since start-up).
- Check the pressure of your spare tire each time you check the pressure of other tires.
Should you overload your vehicle?
Never overload your vehicle. Be careful not to overload a vehicle luggage rack if your vehicle is equipped with one.
How often should you check your tires?
Check your tires once a month or more. Also, check the tire pressure of the spare tire.
How can you check tire pressure?
Use a good quality gauge to check tire pressure. You can not tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they’re underinflated.
How do you check tire pressure?
Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the tire and loading information label, no further adjustment is necessary. If the pressure is low, add air until you reach the recommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gauge. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.
What can result from overinflating or underinflating tires?
Overinflation or underinflation can reduce tire life, adversely affect vehicle handling, and lead to sudden tire failure. This could result in loss of vehicle control and potential injury.
What should you do when inspecting your tires?
Inspect your tires frequently for proper inflation as well as wear and damage. Always use a tire pressure gauge.
What can happen if you drive with too much or too little tire pressure?
Tires with too much or too little pressure wear unevenly causing poor handling, loss of vehicle control, and sudden tire failure leading to accidents, injuries, and even death.
Where can you find the recommended cold tire pressure for your vehicle?
The recommended cold tire pressure for your vehicle can be found in this manual and on the tire label located on the driver’s side center pillar.
How often should you check the spare tire?
Kia recommends that you check the spare every time you check the pressure of the other tires on your vehicle.
How often should you rotate your tires?
To equalize tread wear, it is recommended that the tires be rotated every 7,500 miles (12,000 km) or sooner if irregular wear develops.
What should you check during tire rotation?
During rotation, check the tires for correct balance. When rotating tires, check for uneven wear and damage.
What causes abnormal tire wear?
Abnormal wear is usually caused by incorrect tire pressure, improper wheel alignment, out-of-balance wheels, severe braking or severe cornering.
What should you look for when inspecting tires?
Look for bumps or bulges in the tread or side of tire. Replace the tire if you find either of these conditions. Replace the tire if fabric or cord is visible.
What should you do after tire rotation?
After rotation, be sure to bring the front and rear tire pressures to specification and check lug nut tightness.
What should you do with disc brake pads when rotating tires?
Disc brake pads should be inspected for wear whenever tires are rotated.
How should you rotate radial tires with an asymmetric tread pattern?
Rotate radial tires that have an asymmetric tread pattern only from front to rear and not from right to left.
What should you do if you notice your vehicle vibrating while driving?
If you notice your vehicle vibrating while driving, have the wheels aligned and balanced carefully.
Should you use the compact spare tire for tire rotation?
Do not use the compact spare tire (if equipped) for tire rotation.
Should you mix bias ply and radial ply tires?
Do not mix bias ply and radial ply tires under any circumstances. This may cause unusual handling characteristics.
How do you know when to replace a tire due to wear?
If the tire is worn evenly, a tread wear Indicator (A) will appear as a solid band across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. Replace the tire when this happens.
Should you wait for the band to appear across the entire tread before replacing a tire?
Do not wait for the band to appear across the entire tread before replacing the tire.
Why is tire size important for the ABS and ESC systems?
The ABS works by comparing the speed of the wheels. The tire size affects wheel speed. When replacing tires, all 4 tires must use the same size originally supplied with the vehicle.
What can happen if you use tires of a different size?
Using tires of a different size can cause the ABS (Anti-lock Brake System) and ESC (Electronic Stability Control) to work irregularly.
What do you recommend when replacing tires?
We recommend that when replacing tires, use the same which were originally supplied with the vehicle. If not, driving performance could be altered.
When should you replace a compact spare tire?
A compact spare tire has a shorter tread life than a regular size tire. Replace it when you can see the tread wear indicator bars on the tire.
What type of replacement compact spare tire should you use?
The replacement compact spare tire should be the same size and design tire as the one provided with your new vehicle and should be mounted on the same compact spare tire wheel.
Can a compact spare tire be mounted on a regular size wheel?
The compact spare tire is not designed to be mounted on a regular size wheel.
Can a regular size tire be mounted on a compact spare tire wheel?
The compact spare tire wheel is not designed for mounting a regular size tire.
What should you make sure of when replacing the metal wheels?
When replacing the metal wheels for any reason, make sure the new wheels are equivalent to the original factory units in diameter, rim width and offset.
What can happen if the wheel is not the correct size?
A wheel that is not the correct size may adversely affect wheel and bearing life, braking and stopping abilities, handling characteristics, ground clearance, body-to-tire clearance, snow chain clearance, speedometer and odometer calibration, headlight aim and bumper height.
What can reduce tire traction?
Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces.
When should tires be replaced due to wear?
Tires should be replaced when tread wear indicators appear.
What should you do when driving in rain, snow, or ice?
Slow down whenever there is rain, snow or ice on the road, to reduce the possibility of losing control of the vehicle.
What does correct wheel alignment help with?
Correct wheel alignment helps to decrease tire wear.
What should you do if a tire is worn unevenly?
If you find a tire is worn unevenly, have your dealer check the wheel alignment.
What should you do when you install new tires?
When you have new tires installed, make sure they are balanced. This will increase vehicle ride comfort and tire life. Additionally, a tire should always be rebalanced if it is removed from the wheel.
What is the tire sidewall labeling used for?
This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.
What can happen if you use wheels that do not meet specifications?
Wheels that do not meet Kia’s specifications may fit poorly and result in damage to the vehicle or unusual handling and poor vehicle control.
Where can you find the tire size designation?
A tire’s sidewall is marked with a tire size designation.
What do the letters and numbers in the tire size designation mean?
- P – Applicable vehicle type (tires marked with the prefix “P’’ are intended for use on passenger vehicles or light trucks; however, not all tires have this marking).
- 205 – Tire width in millimeters.
- 55 – Aspect ratio. The tire’s section height as a percentage of its width.
- R – Tire construction code (Radial).
- 16 – Rim diameter in inches.
- 89 – Load Index, a numerical code associated with the maximum load the tire can carry.
- H – Speed Rating Symbol.
What do the letters and numbers in the wheel size designation mean?
- 6.0 – Rim width in inches.
- J – Rim contour designation.
- 16 – Rim diameter in inches.
How old should tires be before they are replaced?
Any tires that are over 6 years old, based on the manufacturing date, (including the spare tire) should be replaced by new ones.
Where can you find the manufacturing date of a tire?
You can find the manufacturing date on the tire sidewall (possibly on the inside of the wheel), displaying the DOT Code.
How do you read the DOT code to find the manufacturing date?
The manufacturing date is designated by the last four digits (characters) of the DOT code. For example: DOT XXXX XXXX 1618 represents that the tire was produced in the 16th week of 2018.
What does the tire ply composition and material refer to?
The number of layers or plies of rubber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others.
What do the letters “R”, “D”, and “B” mean in tire ply composition?
The letter “R” means radial ply construction; the letter “D” means diagonal or bias ply construction; and the letter “B” means belted-bias ply construction.
What is the maximum permissible inflation pressure?
This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure.
Where can you find the recommended inflation pressure?
Refer to the Tire and Loading Information label for recommended inflation pressure.
What does the maximum load rating indicate?
This number indicates the maximum load in kilograms and pounds that can be carried by the tire.
What should you do when replacing tires with respect to the load rating?
When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.
Where can quality grades be found on a tire?
Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
What are the risks of not replacing tires within the recommended time frame?
Failure to replace tires as recommended can result in sudden tire failure, which could lead to a loss of control and an accident.
What does the tread wear grade indicate?
The tread wear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
What do the traction grades represent?
The traction grades, from highest to lowest, are AA, A, B and C. Those grades represent the tires ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
What does the temperature grade represent?
The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
What is “Air Pressure” in tire terminology?
The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in kilopascals (kPa) or pounds per square inch (psi).
What is “Accessory Weight” in tire terminology?
This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transaxle, power seats, and air conditioning.
What is “Aspect Ratio” in tire terminology?
The relationship of a tire’s height to its width.
What is a “Belt” in tire terminology?
A rubber-coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials.
What is a “Bead” in tire terminology?
The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim.
What is a “Bias Ply Tire”?
A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.
What does “GVWR” mean?
Gross Vehicle Weight Rating.
What does “GAWR FRT” mean?
Gross Axle Weight Rating for the Front Axle.
What does “GAWR RR” mean?
Gross Axle Weight Rating for the Rear axle.
What does “Intended Outboard Sidewall” mean?
The side of an asymmetrical tire, that must always face outward when mounted on a vehicle.
What does “Kilopascal (kPa)” mean?
The metric unit for air pressure.
What is a “Light truck(LT) tire”?
A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles.
What is “Load Index”?
An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire.
What are “Load ratings”?
The maximum load that a tire is rated to carry for a given inflation pressure.
What is “Maximum Inflation Pressure”?
The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall.
What is “Maximum Load Rating”?
The load rating for a tire at the maximum permissible inflation pressure for that tire.
What is “Maximum Loaded Vehicle Weight”?
The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight.
What is “Normal Occupant Weight”?
The number of occupants a vehicle is designed to seat multiplied by 150 lbs. (68kg).
What is “Occupant Distribution”?
Designated seating positions.
What is an “Outward Facing Sidewall”?
The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The outward-facing sidewall bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the inner-facing sidewall.
What is a “Passenger (P-Metric) Tire”?
A tire used on passenger cars and some light-duty trucks and multipurpose vehicles.
What is a “Ply”?
A layer of rubber-coated parallel cords.
How should you handle halogen bulbs?
Handle halogen bulbs with care. They contain pressurized gas that will produce flying pieces of glass if broken. Always handle them carefully, and avoid scratches and abrasions. If the bulbs are lit, avoid contact with liquids. Never touch the glass with bare hands, as residual oil may cause the bulb to overheat and burst when lit. A bulb should be operated only when installed in a headlamp. If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it. Wear eye protection when changing a bulb, and allow the bulb to cool down before handling it.
How do you replace the Headlamp (High/Low beam) bulb?
- Open the hood.
- Remove the headlamp bulb cover by turning it counterclockwise.
- Disconnect the headlamp bulb socket-connector.
- Remove the bulb-socket from the headlamp assembly by turning the bulb-socket counterclockwise until the tabs on the bulb-socket align with the slots on the headlamp assembly.
- Install a new bulb-socket assembly in the headlamp assembly by aligning the tabs on the bulb-socket with the slots in the headlamp assembly.
- Push the bulb-socket into the headlamp assembly and turn the bulb-socket clockwise.
- Install the headlamp bulb cover by turning it clockwise.
How do you replace the Front turn signal lamp bulb?
- Open the hood.
- Remove the bulb-socket from the headlamp assembly by turning the bulb-socket counterclockwise until the tabs on the bulb-socket align with the slots on the headlamp assembly.
- Remove the bulb from the bulb-socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the bulb-socket.
- Pull the bulb out of the bulb-socket.
- Insert a new bulb by inserting it into the bulb-socket and rotating it until it locks into place.
- Install the socket in the headlamp assembly by aligning the tabs on the bulb-socket with the slots in the assembly.
- Push the bulb-socket into the headlamp assembly and turn the socket clockwise.
How do you replace the Position lamp + DRL bulb?
- Open the hood.
- Remove the bulb-socket from the headlamp assembly by turning the bulb-socket counterclockwise until the tabs on the bulb-socket align with the slots on the headlamp assembly.
- Remove the bulb from the bulb-socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the bulb-socket.
- Pull the bulb out of the bulb-socket.
- Insert a new bulb by inserting it into the bulb-socket and rotating it until it locks into place.
- Install the socket in the headlamp assembly by aligning the tabs on the bulb-socket with the slots in the assembly.
- Push the bulb-socket into the headlamp assembly and turn the socket clockwise.
What should you do if the front fog lamp (Bulb and LED type) does not operate?
If the front fog lamp (Bulb and LED type) does not operate, it is recommended that you have your vehicle checked by an authorized Kia dealer.
How do you replace the Stop and tail lamp bulb?
- Open the tailgate.
- Open the service cover.
- Loosen the light assembly retaining screws with a cross-tip screwdriver.
- Remove the rear combination lamp assembly from the body of the vehicle.
- Disconnect the rear combination lamp connector.
- Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
- Remove the bulb from the socket by pressing it in and rotating it counter-clockwise until the tabs on the bulb align with the slots in the socket.
- Pull the bulb out of the socket.
- Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
- Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.
- Push the socket into the assembly and turn the socket clockwise.
- Install the rear combination lamp assembly to the body of the vehicle.
- Install the service cover.
How do you replace the Tail lamp (inside) bulb?
- Open the tailgate.
- Remove the service cover.
- Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
- Remove the bulb from the socket by pressing it in and rotating it counter-clockwise until the tabs on the bulb align with the slots in the socket.
- Pull the bulb out of the socket.
- Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
- Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.
- Push the socket into the assembly and turn the socket clockwise.
- Install the service cover by putting it into the service hole.
What should you do if the stop and tail lamp (LED) does not operate?
If the stop and tail lamp (LED) does not operate, it is recommended that you have your vehicle checked by an authorized Kia dealer.
What should you do if the Back-up lamp and Rear turn signal lamp does not operate?
If the Back-up lamp and Rear turn signal lamp does not operate, it is recommended that you have your vehicle checked by an authorized Kia dealer.
What should you do if the high mounted stop lamp (LED) does not operate?
If the high mounted stop lamp (LED) does not operate, it is recommended that you have your vehicle checked by an authorized Kia dealer.
How do you replace the License plate lamp bulb?
- Using a flat-blade screwdriver, gently pry the lens cover from lamp housing.
- Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
- Remove the bulb from bulb-socket by pulling it out.
- Insert a new bulb by inserting it into the bulb-socket.
- Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.
- Push the socket into the assembly and turn the socket clockwise.
- Align the lens cover tabs with the lamp housing notches and snap the lens into place.
What should you do if the side repeater lamp (LED type) does not operate?
If the side repeater lamp (LED type) does not operate, it is recommended that you have your vehicle checked by an authorized Kia dealer.
What should you do if the map lamp (bulb and LED type) does not operate?
If the map lamp (bulb and LED type) does not operate, it is recommended that you have your vehicle checked by an authorized Kia dealer.
How do you replace the Vanity mirror lamp bulb?
- Using a flat-blade screwdriver, gently pry the lamp assembly from interior.
- Remove the bulb by pulling it straight out.
- Install a new bulb in the socket.
- Install the lamp assembly to interior.
What precaution should be taken prior to working on interior lamps?
Prior to working on the Interior lamps, ensure that the “OFF” button is depressed to avoid burning your fingers or receiving an electric shock.
How do you replace the Room lamp bulb?
- Using a flat-blade screwdriver, gently pry the lens cover from lamp housing.
- Remove the bulb by pulling it straight out.
- Install a new bulb in the socket.
- Align the lens cover tabs with the lamp housing notches and snap the lens into place.
How do you replace the Glove box lamp bulb?
- Using a flat-blade screwdriver, gently pry the lamp assembly from interior.
- Remove the bulb by pulling it straight out.
- Install a new bulb in the socket.
- Install the lamp assembly to interior.
What should you do if the personal lamp (LED) does not operate?
If the personal lamp (LED) does not operate, it is recommended that you have your vehicle checked by an authorized Kia dealer.
How do you replace the Tailgate room lamp bulb?
- Using a flat-blade screwdriver, gently pry the lens cover from lamp housing.
- Remove the bulb by pulling it straight out.
- Install a new bulb in the socket.
- Align the lens cover tabs with the lamp housing notches and snap the lens into place.
What should you do when using chemical cleaners or polish on the exterior of the vehicle?
It is very important to follow the label directions when using any chemical cleaner or polish. Read all warning and caution statements that appear on the label.
How often should you wash the vehicle?
To help protect your vehicle’s finish from rust and deterioration, wash it thoroughly and frequently at least once a month with lukewarm or cold water. If you use your vehicle for off-road driving, you should wash it after each off-road trip.
What areas should you pay special attention to when washing the vehicle?
Pay special attention to the removal of any accumulation of salt, dirt, mud, and other foreign materials. Make sure the drain holes in the lower edges of the doors and rocker panels are kept clear and clean.
What can damage the vehicle’s finish if not removed immediately?
Insects, tar, tree sap, bird droppings, industrial pollution and similar deposits can damage your vehicle’s finish if not removed immediately.
What kind of soap should be used on the vehicle’s paint?
A mild soap, safe for use on painted surfaces, may be used.
What should you do after washing the vehicle?
After washing, rinse the vehicle thoroughly with lukewarm or cold water. Do not allow soap to dry on the finish. Test the brakes while driving slowly to see if they have been affected by water. If braking performance is impaired, dry the brakes by applying them lightly while maintaining a slow forward speed.
What should you do when using a high-pressure washer?
When using high-pressure washers, make sure to maintain sufficient distance from the vehicle. Insufficient clearance or excessive pressure can lead to component damage or water penetration. Do not spray the camera, sensors or its surrounding area directly with a high pressure washer. Shock applied from high pressure water may cause the device to not operate normally. Do not bring the nozzle tip close to boots (rubber or plastic covers) or connectors as they may be damaged if they come into contact with high pressure water.
When should you wax the vehicle?
Wax the vehicle when water will no longer bead on the paint.
What should you do before waxing the vehicle?
Always wash and dry the vehicle before waxing.
What should you use to wax the vehicle?
Use a good quality liquid or paste wax, and follow the manufacturer’s instructions. Wax all metal trim to protect it and to maintain its luster.
What should you do after removing oil, tar, and similar materials with a spot remover?
Removing oil, tar, and similar materials with a spot remover will usually strip the wax from the finish. Be sure to re-wax these areas even if the rest of the vehicle does not yet need waxing.
What should you not apply wax to?
Do not apply wax on embossed unpainted unit, as it may tarnish the unit.
What can water washing in the engine compartment cause?
Water washing in the engine compartment including high pressure water washing may cause the failure of electrical circuits located in the engine compartment.
What should you never allow water or other liquids to come in contact with inside the vehicle?
Never allow water or other liquids to come in contact with electrical/electronic components inside the vehicle as this may damage them.
When should you repair deep scratches or stone chips in the painted surface?
Deep scratches or stone chips in the painted surface must be repaired promptly.
What will happen to exposed metal?
Exposed metal will quickly rust and may develop into a major repair expense.
What should you do if your vehicle is damaged and requires any metal repair or replacement?
If your vehicle is damaged and requires any metal repair or replacement, be sure the body shop applies anti-corrosion materials to the parts repaired or replaced.
How should you remove road tar and insects from bright-metal parts?
To remove road tar and insects, use a tar remover, not a scraper or other sharp object.
How should you protect the surfaces of bright-metal parts from corrosion?
To protect the surfaces of bright-metal parts from corrosion, apply a coating of wax or chrome preservative and rub to a high luster.
What should you do with bright metal parts during winter weather or in coastal areas?
During winter weather or in coastal areas, cover the bright metal parts with a heavier coating of wax or preservative. If necessary, coat the parts with non-corrosive petroleum jelly or other protective compound.
What should you do to the undercarriage of the vehicle during the winter?
Wash the undercarriage of your vehicle regularly during the winter and whenever your vehicle has been exposed to such salts or chemicals.
What can wiping dust or dirt off the body with a dry cloth cause?
Wiping dust or dirt off the body with a dry cloth will scratch the finish.
What should you not use on chrome-plated or anodized aluminum parts?
Do not use steel wool, abrasive cleaners, acid detergents or strong detergents containing high alkaline or caustic agents on chrome-plated or anodized aluminum parts. This may result in damage to the protective coating and cause discoloration or paint deterioration.
What should you do at the end of winter?
Do a thorough washing of the undercarriage at the end of the winter.
What should you use to inspect for corrosion?
Use professional service technicians or governmental inspection stations to annually inspect for corrosion.
When should you seek an inspection of your vehicle?
Immediately seek an inspection of your vehicle if you become visually aware of corrosion flaking or scaling or if you become aware of a change in vehicle performance, such as soft or spongey brakes, fluids leaking, impairment of directional control, suspension noises or rattling metal straps.
What should you not use on aluminum wheels?
Do not use any abrasive cleaner, polishing compound, solvent, or wire brushes on aluminum wheels, as they may scratch the finish.
When should you clean the wheels?
Clean the wheels when it has cooled.
What should you use to clean the wheels?
Use only a mild soap or neutral detergent, and rinse thoroughly with water.
What should you do to the wheels after driving on salted roads?
Be sure to clean the wheels after driving on salted roads, as this helps prevent corrosion.
What should you avoid when washing the wheels?
Avoid washing the wheels with highspeed vehicle wash brushes.
What kind of detergents should you not use on aluminum wheels?
Do not use any alkaline or acid detergents. It may damage and corrode the aluminum wheels coated with a clear protective finish.
What should you do to help prevent corrosion?
Keep your vehicle clean. The best way to prevent corrosion is to keep your vehicle clean and free of corrosive materials. Attention to the underside of the vehicle is particularly important.
What should you do if you live in a high-corrosion area?
If you live in a high-corrosion area — where road salts are used, near the ocean, areas with industrial pollution, acid rain, etc.—, you should take extra care to prevent corrosion. In winter, hose off the underside of your vehicle at least once a month and be sure to clean the underside thoroughly when winter is over. When cleaning underneath the vehicle, give particular attention to the components under the fenders and other areas that are hidden from view. Do a thorough job; just dampening the accumulated mud rather than washing it away will accelerate corrosion rather than prevent it. Water under high pressure and steam are particularly effective in removing accumulated mud and corrosive materials.
What should you ensure when cleaning lower door panels, rocker panels, and frame members?
When cleaning lower door panels, rocker panels and frame members, be sure that drain holes are kept open so that moisture can escape and not be trapped inside to accelerate corrosion.
Where should you not park your vehicle to avoid corrosion?
Don’t park your vehicle in a damp, poorly ventilated garage, as this creates a favorable environment for corrosion. This is particularly true if you wash your vehicle in the garage or drive it into the garage when it is still wet or covered with snow, ice or mud. Even a heated garage can contribute to corrosion unless it is well ventilated so moisture is dispersed.
What should you do with scratches or chips in the vehicle’s finish?
Scratches or chips in the finish should be covered with “touch-up” paint as soon as possible to reduce the possibility of corrosion. If bare metal is showing through, the attention of a qualified body and paint shop is recommended.
How should you handle bird droppings?
Bird droppings are highly corrosive and may damage painted surfaces in just a few hours. Always remove bird droppings as soon as possible.
What should you be careful of when carrying fertilizers, cleaning materials or chemicals in the vehicle?
Moisture can collect under the floor mats and carpeting and cause corrosion. Check under the mats periodically to be sure the carpeting is dry. Use particular care if you carry fertilizers, cleaning materials or chemicals in the vehicle. These should be carried only in proper containers and any spills or leaks should be cleaned up, flushed with clean water and thoroughly dried.
What chemicals should you prevent from contacting the interior parts?
Prevent chemicals such as perfume, cosmetic oil, sun cream, hand cleaner, and air freshener from contacting the interior parts because they may cause damage or discoloration.
What should you do if chemicals contact the interior parts?
If chemicals contact the interior parts, wipe them off immediately. If necessary, use a vinyl cleaner, see product instructions for correct usage.
What should you never allow water or other liquids to come in contact with inside the vehicle?
Never allow water or other liquids to come in contact with electrical/electronic components inside the vehicle as this may damage them.
How should you take care of leather seats?
- Vacuum the seat periodically to remove dust and sand on the seat to prevent abrasion or damage of the leather and maintain its quality.
- Wipe the natural leather seat cover often with dry or soft cloth.
- Sufficient use of a leather protective may prevent abrasion of the cover and helps maintain the color. Be sure to read the instructions and consult a specialist when using leather coating or protective agents.
- Leather with bright colors(beige, cream beige) is easily contaminated and clear in appearance. Clean the seats frequently.
- Avoid wiping with wet cloth, as it may cause the surface to crack.
How should you clean leather seats?
- Remove all contaminations instantly.
- For cosmetic products(sunscreen, foundation, etc.) – Apply cleansing cream on a cloth and wipe the contaminated point. Wipe off the cream with a wet cloth and remove water with a dry cloth.
- For beverages(coffee, soft drink, etc.) – Apply a small amount of neutral detergent and wipe until contaminations do not smear.
- For oil – Remove oil instantly with absorbable cloth and wipe with stain remover for natural leather only.
- For chewing gum – Harden the gum with ice and remove gradually.
What should you use when cleaning leather products?
When cleaning leather products (steering wheel, seats etc.), use neutral detergents or low alcohol content solutions. If you use high alcohol content solutions or acid/alkaline detergents, the color of the leather may fade or the surface may get stripped off.
How should you clean fabric seats?
Please clean the fabric seats regularly with a vacuum cleaner in consideration of fabric material characteristics. If they are heavily soiled with beverage stains, etc., use a suitable interior cleaner. To prevent damage to seat covers, wipe off the seat covers down to the seams with a large wiping motion and moderate pressure using a soft sponge or microfiber cloth.
What should you make sure not to do on the surface of the fabric seats?
Velcro closures on clothing or sharp objects may cause snagging or scratches on the surface of the seats. Make sure not to rub such objects against the surface.
How should you clean vinyl upholstery?
Remove dust and loose dirt from vinyl with a whisk broom or vacuum cleaner. Clean vinyl surfaces with a vinyl cleaner.
How should you clean fabric upholstery?
Remove dust and loose dirt from fabric with a whisk broom or vacuum cleaner. Clean with a mild soap solution recommended for upholstery or carpets. Remove fresh spots immediately with a fabric spot cleaner.
What may happen if fresh spots on fabric upholstery do not receive immediate attention?
If fresh spots do not receive immediate attention, the fabric can be stained and its color can be affected. Also, its fire-resistant properties can be reduced if the material is not properly maintained. Using anything but recommended cleaners and procedures may affect the fabric’s appearance and fire-resistant properties.
How should you clean the lap/shoulder belt webbing?
Clean the belt webbing with any mild soap solution recommended for cleaning upholstery or carpet. Follow the instructions provided with the soap. Do not bleach or re-dye the webbing because this may weaken it.
How should you clean the interior window glass?
If the interior glass surfaces of the vehicle become fogged (that is, covered with an oily, greasy or waxy film), they should be cleaned with a glass cleaner. Follow the directions on the glass cleaner container.
What should you not do to the rear window?
Do not scrape or scratch the inside of the rear window. This may result in damage of the rear window defroster grid.
How should you operate the vehicle during a dynamometer test?
To prevent the vehicle from misfiring during dynamometer testing, turn the Electronic Stability Control (ESC) system off by pressing the ESC switch.
What should you do after dynamometer testing is completed?
After dynamometer testing is completed, turn the ESC system back on by pressing the ESC switch again.
What does the Evaporative Emission Control System do?
The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere. The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, preventing the escape of fuel vapors into the atmosphere.
What happens to fuel vapors in the canister?
Fuel vapors generated inside the fuel tank are absorbed and stored in the onboard canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the surge tank through the purge control solenoid valve.
How does the Purge Control Solenoid Valve (PCSV) work?
The purge control solenoid valve is controlled by the Engine Control Module (ECM). When the engine coolant temperature is low during idling, the PCSV closes so that evaporated fuel is not taken into the engine. After the engine warms up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine.
What should you not do to your vehicle?
This vehicle should not be modified. Modification of your vehicle could affect its performance, safety or durability and may even violate governmental safety and emissions regulations. In addition, damage or performance problems resulting from any modification may not be covered under warranty. If you use unauthorized electronic devices, it may cause the vehicle to operate abnormally, wire damage, battery discharge and fire. For your safety, do not use unauthorized electronic devices.
What should you do if you smell exhaust fumes inside your vehicle?
If you smell exhaust fumes of any kind inside your vehicle, have it inspected and repaired immediately. If you ever suspect exhaust fumes are coming into your vehicle, drive it only with all the windows fully open, then have your vehicle checked and repaired immediately.
What should you not do in confined or closed areas with the engine running?
Do not operate the engine in confined or closed areas (such as garages) any more than what is necessary to move the vehicle in or out of the area.
What should you do when the vehicle is stopped in an open area for more than a short time with the engine running?
When the vehicle is stopped in an open area for more than a short time with the engine running, adjust the ventilation system (as needed) to draw outside air into the vehicle.
What should you never do with the engine running?
Never sit in a parked or stopped vehicle for any extended time with the engine running.
What can excessive attempts to restart the engine cause?
When the engine stalls or fails to start, excessive attempts to restart the engine may cause damage to the emission control system.
What should you keep away from while the vehicle is running or immediately thereafter?
Keep away from the catalytic converter and exhaust system while the vehicle is running or immediately thereafter. The exhaust and catalytic systems are very hot and may burn you.
What should you not do with the vehicle near flammable objects?
Do not park, idle or drive the vehicle over or near flammable objects, such as grass, vegetation, paper, leaves, etc. A hot exhaust system can ignite flammable items under your vehicle.
What should you not do to the heat sink around the exhaust system?
Do not remove the heat sink around the exhaust system, do not seal the bottom of the vehicle or do not coat the vehicle for corrosion control, as it may present a fire risk under certain conditions.
What kind of fuel must be used for gasoline engines?
Use only UNLEADED FUEL for gasoline engines.
What should you not do when there are signs of engine malfunction?
Do not operate the vehicle when there are signs of engine malfunction, such as misfire or a noticeable loss of performance.
What should you not do with the engine?
Do not misuse or abuse the engine. Examples of misuse are coasting with the ignition off and descending steep grades in gear with the ignition off.
What should you not do with the engine at high idle speed?
Do not operate the engine at high idle speed for extended periods (5 minutes or more).
What should you not do to the engine or emission control system?
Do not modify or tamper with any part of the engine or emission control system. All inspections and adjustments must be made by an authorized Kia dealer.
What should you avoid doing with an extremely low fuel level?
Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the catalytic converter.
What should you do when replacing tires?
When replacing tires, use the same size originally supplied with the vehicle. Using tires of a different size can damage the related parts or make them work irregularly.
How much air can be added to the standard tire pressure specification if colder temperatures are expected soon?
It is permissible to add 3psi to the standard tire pressure specification if colder temperatures are expected soon.
What should you do if extreme temperature variations are expected with the tire pressure?
If extreme temperature variations are expected, re-check your tire pressure as necessary to keep them properly inflated.
What is recommended when replacing tires?
We recommend that when replacing tires, use the same originally supplied with the vehicles. If not, that affects driving performance.
What should you do with tire pressure when driving in high altitude grades?
When driving in high altitude grades, it is natural for the atmospheric pressure to decrease. Therefore, please check the tire pressure and add more air when necessary. Additionally required tire air pressure per km above sea level: 1.5psi/km.
What should you do to ensure proper engine and powertrain performance?
To help achieve proper engine and powertrain performance and durability, use only lubricants of the proper quality. The correct lubricants also help promote engine efficiency that results in improved fuel economy.
What can using oils of any viscosity other than those recommended cause?
Using oils of any viscosity other than those recommended could result in engine damage.
What is recommended to use for engine oils?
It is recommended to only use engine oils that uphold this API Certification Mark.
What should you do before any additional electrical equipment is installed in your vehicle?
Before any additional electrical equipment is installed in your vehicle, consult an Authorized Kia Dealer, in order to ensure that you do not void your warranty.
What may happen if you install certain electrical equipment?
Certain electrical equipment, or the way in which it is installed, may adversely affect the operation of your vehicle, including such systems as the engine control system, the audio system and the electrical charging system and thus potentially void all or part of your warranty.
What should you do if you install a mobile two-way radio system or an excessively powerful electronic system?
If a mobile two-way radio system or if an excessively powerful electronic system is installed, and it causes damage to your vehicle, consult an Authorized Kia Dealer concerning the proper equipment.
What should you do if you believe that your vehicle has a defect which could cause a crash or could cause injury or death?
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Kia Motors America, Inc.
How can you contact NHTSA?
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; download the SaferCar mobile application; or write to: Administrator, NHTSA, 1200 New Jersey Ave. SE., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
What should you do if the light bulb does not operate on an HID Headlamp (if equipped)?
Do not attempt to replace or inspect the HID headlamp (XENON bulb) due to electric shock danger. If the light bulb does not operate, have your vehicle checked by an authorized Kia dealer.
What should you do if you do not have the necessary tools, the correct bulbs and the expertise to replace a bulb?
If you don’t have the necessary tools, the correct bulbs and the expertise, consult an authorized Kia dealer.
What can happen if non-genuine parts or substandard bulbs are used?
If non-genuine parts or substandard bulbs are used, it may lead to blowing a fuse or other wiring damages.
What should you not install on the vehicle?
Do not install extra lamps or LEDs to the vehicle. If additional lights are installed, it may lead to lamp malfunctions and flickering. Additionally, the fuse box and other writing may be damaged.
CLICK HERE TO DOWNLOAD KIA SPORTAGE 2019 (01) PDF MANUAL