KENWOOD SB200 (01) PDF MANUAL

The wires in the cord are coloured as follows:

Blue = Neutral, Brown = Live.

The appliance must be protected by a 3A approved (BS1362) fuse.

For non-rewireable plugs the fuse cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained. The correct fuse cover is identified by colour and a replacement may be obtained.

If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY. An electric shock hazard may arise if an unwanted non-rewireable plug is inadvertently inserted into a 13A socket outlet.

Switch off and unplug:

before fitting and removing parts

after use

before cleaning.

Never let the power unit, cord or plug get wet.

Keep hands and utensils, other than the stirrer out of the goblet when it’s on the power unit.

Don’t touch sharp blades.

Don’t let children or infirm people use the machine unsupervised.

Never blend hot liquids.

Never use a damaged machine. Get it checked or repaired.

Never use an unauthorised attachment.

Never leave the machine on unattended.

Don’t let children play with the machine.

When removing the Smoothie Blender from the power unit, wait until the blades have completely stopped.

Only use the appliance for its intended domestic use.

Only operate the Smoothie Blender with the lid in place.

Never use the stirrer unless the lid is fitted to the goblet.

Make sure your electricity supply is the same as the one shown on the underside of the machine.

1 Remove all the packaging

2 Wash the parts: see ‘cleaning’.

1 stirrer

2 cap

3 lid

4 goblet

5 tap assembly

6 sealing ring

7 blade assembly

8 power unit

1 Fit the sealing ring over the blade assembly.

2 Screw the goblet onto the blade unit.

3 Screw the tap assembly onto the goblet, then place on the power unit.

Check that the dispensing tap lever is in the off position.

4 Place the liquid ingredients into the goblet.

This includes fruit (not frozen), fresh yoghurt, milk and fruit juices. These can be placed into the goblet to the level marked LIQUIDS for either 2 or 4 servings.

5 Add ice or frozen ingredients to the goblet.

This includes frozen fruit, frozen yoghurt, ice cream or ice. These can be added up to the level marked FROZEN INGREDIENTS for the corresponding number of servings.

6 Screw the lid onto the goblet.

7 Either put the cap into the lid, then turn. Or place the stirrer in the hole.

The stirrer can be used when blending thick mixtures or when large quantities of frozen items are used.

8 Press the MIX button for up to 30 seconds, this is to start the mixing process, then press the SMOOTH button. Allow the ingredients to blend until smooth.

Use the stirrer by moving it in an anti clockwise direction.

9 Place a glass under the tap, press the MIX button and press down on the dispensing tap lever.

Thinner drinks may dispense without having to switch on the power unit.

Use the stirrer to assist when dispensing thick smoothie drinks.

To help dispense the last amount of a thick smoothie drink, add a few tablespoons of liquid to increase the flow.

10 When the glass is full, switch off and release the lever.

To make a thinner smoothie drink add more liquid.

To make a thicker smoothie drink add more frozen ingredients.

Before fitting the lid, push the solid ingredients into the liquid using the stirrer.

Use the PULSE button to operate the power unit in a start stop action to control the texture of your drink. Take care as this automatically selects the higher speed and may cause the drink to be thrown up the sides and onto the lid of the goblet.

After blending, some drinks may not be completely smooth due to seeds or the fibrous nature of ingredients. Some drinks may separate on standing, therefore it’s best to drink them straight away. Separated drinks should be stirred before drinking.

Never blend dry ingredients (eg spices, nuts) or run the Smoothie Blender empty – it’s intended for blending smoothie drinks only.

Don’t use the blender as a storage container. Keep it empty before and after use.

Some liquids increase in volume and froth during blending eg milk, so do not overfill and ensure the lid is correctly fitted.

To ensure long life of your Smoothie Blender, never run it continuously for longer than 60 seconds.

Never blend food that has formed a solid mass during freezing, break it up before adding to the goblet.

Always switch off, unplug and dismantle before cleaning.

Never let the power unit, cord or plug get wet.

Empty the goblet before unscrewing it from the blade unit.

Always wash immediately after use. Don’t let food dry onto the goblet assembly as this will make cleaning difficult.

Don’t wash any part in the dishwasher.

Regularly dismantle the tap and clean the parts thoroughly.

Before dismantling the blender, half fill the goblet with warm water. Fit the lid and cap then place on the power unit. Switch to MIX and whilst running open the tap and allow the water to drain into a container to clean the valve. This can be repeated until the water runs clear. If further cleaning is necessary dismantle the unit first.

Wipe with a damp cloth, then dry.

1 Remove and wash the sealing ring.

2 Don’t touch the sharp blades – brush them clean using hot soapy water, then rinse thoroughly under the tap. Don’t immerse the blade assembly in water.

3 Leave to dry upside down away from children.

Wash by hand, rinse with clean water then dry.

Remove the tap assembly from the goblet, then soak the tap in hot soapy water with the valve open.

Wash thoroughly then rinse and dry.

Wash and dry the goblet then refit the tap ensuring that the seals are correctly positioned on the goblet.

1 Hold the tap by the lever. Push up on the plug whilst sliding the lever in the direction indicated.

2 Unscrew the cap.

3 Remove the spring.

4 Push up on the plug on the inside of the tap and at the same time pull the plug from above.

5 Wash all the components, then dry thoroughly.

6 Reassemble the unit by reversing the above procedure.