JOHN DEERE 1835 (01) PDF MANUAL

JOHN DEERE 1835 (01) PDF SUMMARY:

How should I prepare the machine for the leveling procedure?

1. Unfold and completely raise machine.
2. Properly inflate tires.
3. Disengage all depth control shims.
4. Adjust Wing Depth shims so half are engaged and half are disengaged.
5. Pull forward on level surface to rotate caster wheels to the seeding position. Maintain this position throughout procedure.
6. If equipped, raise fertilizer rockshaft.
7. Lower until sweeps are 25-51 mm (1-2 in.) above ground.

How do I perform the Center Frame Fore Aft Adjustment?

1. Measure location (2) and location (3). If equal, repeat on opposite side. If unequal, proceed as follows.
2. Lower machine and retract lift cylinders.
3. Adjust center frame fore aft bar (1).
4. Completely raise machine then lower until sweeps are 25-51 mm (1-2 in.) above ground.
5. Measure location (2) and location (3). Repeat adjustment procedure until equal.
6. Repeat fore aft adjustment on opposite side of center frame.

How do I perform the 3 Section Wing and 5 Section Inner Wing Side to Side Adjustment?

1. Completely raise machine then lower until sweeps are 25-51 mm (1-2 in.) above ground.
2. Verify only half the depth shims are engaged on wing shim pack.
3. Measure location (2) and (3). If equal, repeat on opposite side. If unequal, proceed as follows.
4. Lower machine and retract lift cylinders.
5. Turn wing shim pack bolt (1) until pressure is relieved from leveling shims.
6. Change number of engaged leveling shims (1) so locations (2) and (3) will be equal.
7. Turn wing shim pack bolt until shims are secure.
8. Completely raise machine then lower until sweeps are 25-51 mm (1-2 in.) above ground.
9. Measure location (2) and (3). Repeat procedure until equal. Repeat on opposite side.

How do I perform the 5 Section Outer Wing Side to Side Adjustment?

1. Completely raise machine then lower until sweeps are 25-51 mm (1-2 in.) above ground.
2. Measure location (3) and (4). If equal, repeat on opposite side. If unequal, proceed as follows.
3. Lower machine and retract lift cylinders.
4. Adjust outer wing eyebolt (5).
5. Completely raise machine then lower until sweeps are 25-51 mm (1-2 in.) above ground.
6. Measure locations (3) and (4). Repeat procedure until equal. Tighten eyebolt and repeat on opposite side.

How do I perform the 5 Section Inner Wing Fore Aft Adjustment?

1. Completely raise machine then lower until sweeps are 25-51 mm (1-2 in.) above ground.
2. Measure location (5) and (6). If equal, repeat on opposite side. If unequal, proceed as follows.
3. Lower machine and retract lift cylinders.
4. Adjust wing frame fore aft bar (4).
5. Completely raise machine then lower until sweeps are 25-51 mm (1-2 in.) above ground.
6. Measure location (5) and (6). Repeat adjustment procedure until equal.
7. Repeat fore aft adjustment on opposite wing.

How do I perform the 3 Section Wing or 5 Section Outer Wing Fore Aft Adjustment?

1. Completely raise machine then lower until sweeps are 25-51 mm (1-2 in.) above ground.
2. Measure location (8) and (9). If equal, repeat on opposite side. If unequal, proceed as follows.
3. Lower machine and retract lift cylinders.
4. Adjust outer wing turnbuckle (7).
5. Completely raise machine then lower until sweeps are 25-51 mm (1-2 in.) above ground.
6. Measure location (8) and (9). Repeat adjustment procedure until equal.
7. Lock turnbuckle.
8. Repeat fore aft adjustment on opposite wing.