INALTO ARBC90TPS (01) PDF DOCUMENT

To ensure your personal safety and avoid damage, please follow these instructions:

• Young children should be supervised to ensure they do not play with the cooker hood.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

• Ensure the cooker hood is switched off before carrying out maintenance, to avoid any possibility of electric shock.

• Never carry out flambé cooking under the cooker hood.

• This cooker hood is not suitable for use over barbecues.

• This cooker hood is for indoor installation only and cannot be installed for external use.

• The Aluminium grease filters must be removed every four weeks (at a maximum) for cleaning to reduce the risk of fire.

• The exhaust from the cooker hood must not be discharged into any heating flue, which may carry combustion products from other sources.

• Exhaust air must not be discharged into a wall cavity, unless the cavity is designed for the purpose.

• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels.

• Always cover lit gas burners with pots or pans when the cooker hood is in use.

• Always switch off gas burners before you remove pots or pans.

• Do not leave lit gas burners exposed due to the risk of fire.

Your INALTO ARBC90TPS Box Canopy Rangehood is supplied with:

• 1 × Rangehood

• 1 x Expandable 150mm pipe

• 1 x Packet of fasteners and wall plugs

• 2 x Stainless Steel flue pieces (upper and lower)

• 1 x Wall Bracket (“hook”) for the rangehood

• 1 x Wall Bracket for the inside of the chimney pieces

• 1 x “Outside Chimney” bracket

• 1 x User Manual

• 1 x Quick Start Guide

The height of the underside of the INALTO ARBC90TPS rangehood must be a minimum of 600mm to a maximum of 800mm from the top of your cooktop surface. For gas cooktops, this is the top of the gas burner. If the installation instructions for your cooktop specify a greater distance than the minimum, then that shall be the minimum height for installation.

The following rules must be strictly followed to obtain optimal air extraction:

• Keep exhaust flue short and straight.

• Do not reduce the size or restrict exhaust flue.

• Keep bends in the exhaust flue to a minimum; the more bends the lower the extraction performance.

• When using flexible flue always install duct with helix pulled taut to minimise pressure loss.

• Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the cooker hood.

Exhaust air must not be discharged into a wall cavity unless the cavity is designed for that purpose. The exhaust from the cooker hood must not be discharged into any heating flue, which may carry combustion products from other sources.

The INALTO ARBC90TPS rangehood cannot be operated in recirculation mode. It is recommended to duct wherever possible.

Please follow these tips on how to correctly duct your rangehood:

• Always use correctly sized ducting.

• Do not reduce the size of the ducting.

• Always use solid ducting.

• Always use non-flammable ducting.

• Always duct to the outside atmosphere.

• Do not use flexible ducting.

• Do not duct into the ceiling space. Always vent to the outside atmosphere.

• Avoid sharp 90 degree bends as much as possible. Use 45 degree bends instead wherever possible.

• Duct to the outside atmosphere using the shortest duct run possible.

• Use cylindrical ducting whenever possible.

Before starting, please refer to the Safety Information and position the rangehood according to the height requirements.

1. Once you’ve determined your installation height, drill 3 holes to install the mounting bracket (hook) onto the wall ensuring that it’s secured in a level position. Tighten the bracket with the screw plug and screw (ST4mm X 30mm).

2. When finished, line up the hood and hang it onto the wall bracket hook.

3. Attach the extensible 150mm tube to the canopy. Put the inside chimney with the outside chimney together, ensuring that the inner chimney piece can move freely inside. Now attach the chimney to the hood.

4. Fix the outside chimney to the canopy, mark the hole and drill 2 holes, then tighten the outside chimney bracket with a screw plug and screw (ST4mm X 30mm).

5. If you need the safety screws fixed into the hood, please mark, drill and tighten the hood with a screw plug and screw (ST4mm X 30mm). Note, you will need to remove the grease filters first.

6. Slide the inner chimney to adjust the inner chimney height. When the required height is reached, mark it and accommodate the inner chimney bracket with a screw plug and screw (ST4mm X 30mm). When finished, fix the inner chimney with the screws (4mm X 8mm) to the inner chimney bracket.

Your INALTO ARBC90TPS rangehood features touch controls with four speed levels of extraction. When powered, the ‘1’ button will be illuminated, indicating standby mode. Press any key to begin operation.

1 – Low Speed: Short press the ‘1’ button. Ideal for cooking with lower steam emissions such as slow cooking, simmering, and boiling with closed pans.

2 – Medium Speed: Short press the ‘2’ button. This is the ideal standard intensity for a normal cooking environment.

3 – High Speed: Short press the ‘3’ button. This is ideal for high-intensity cooking such as grilling, intensive frying, wok cooking, stir-frying, etc.

B – Boost: Short press the ‘B’ for Boost button to operate at maximum intensity for an intensive airflow. After 5 minutes of operation, the rangehood will automatically lower the intensity to setting 3.

• Short press the ‘Light’ button and the LED panel lights will turn on. To turn the lights off, simply push the ‘Light’ button again.

• Long press the ‘Light’ button and the LED light panel will turn on for 5 minutes of operation. After 5 minutes, the motor will turn off automatically.

Before cleaning, ensure the rangehood is disconnected from the main power supply. Ensure it is switched off at the wall socket and the plug is removed.

STAINLESS STEEL SURFACES:

Clean stainless steel surfaces using non-abrasive cleaning products specifically for use on stainless steel. Use even pressure and follow the grain of the stainless steel. A soft cloth reduces the risk of scratching. If the cloth is wet, use a dry soft cloth to wipe down the surface again to reduce the risk of surface rust.

CONTROL PANEL SURFACE:

The control panel can be cleaned using warm soapy water. Ensure the cloth is well wrung before cleaning. Use a dry soft cloth to remove any excess moisture left after cleaning.

ALUMINIUM GREASE FILTER:

• To remove the Aluminium grease filter, use a finger to pull the small locking latch on each filter to release it from the rangehood body. Be careful, as the filter can easily drop down.

• Your aluminium filters can be washed by hand in warm soapy water. For stubborn grease stains use a soft nylon brush. After cleaning, allow the filters to completely dry before refitting.

CAUTION: We do not recommend washing the Aluminium filters within a dishwasher. This can damage the filter and cause discolouration.

In the event of an emergency you should:

• Switch off all rangehood controls.

• Switch the rangehood off at the power outlet and immediately unplug.

If your appliance appears to be operating incorrectly, disconnect it from your electrical supply before troubleshooting. Do not attempt to repair the rangehood yourself.