HIKVISION DS-2CE76K0T-LMFS (01) PDF Document

To prevent serious injury or death, please follow these safeguards when using your HIKVISION DS-2CE76K0T-LMFS:

• You must be in strict compliance with the electrical safety regulations of your nation and region.

• The input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 and IEC62368-1 standard. Refer to technical specifications for detailed information.

• The socket-outlet must be installed near the equipment and be easily accessible.

• An all-pole mains switch should be incorporated into the electrical installation of the building.

• Do not connect multiple devices to one power adapter to avoid overheating or a fire hazard caused by overload.

• Ensure that the plug is firmly connected to the power socket.

• If you notice smoke, odor, or noise from the device, turn off the power immediately, unplug the power cord, and then contact the service center.

• Never attempt to disassemble the camera by unprofessional personnel.

To prevent potential injury or material damage to your HIKVISION DS-2CE76K0T-LMFS, please adhere to the following cautions:

• No naked flame sources, such as lighted candles, should be placed on the equipment.

• Install the equipment according to the instructions in this manual.

• To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation instructions.

• Do not drop the camera or subject it to physical shock.

• Do not touch sensor modules with your fingers.

• Do not place the camera in extremely hot, cold (the operating temperature shall be -40°C to 60°C), dusty, or damp locations, and do not expose it to high electromagnetic radiation.

• If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently.

• Do not aim the camera at the sun or extra bright places.

• The sensor may be burned out by a laser beam, so when any laser equipment is in use, make sure that the surface of the sensor will not be exposed to the laser beam.

• Do not expose the device to high electromagnetic radiation or extremely hot, cold, dusty, or damp environments.

• To avoid heat accumulation, good ventilation is required for the operating environment.

• Keep the camera away from liquid while in use for non-water-proof devices.

• While in delivery, the camera shall be packed in its original packing, or packing of the same texture.

The beam of light at a distance of 200 mm is classified as Risk Group 1 (RG1). Possible hazardous optical radiation is emitted from this product.

• DO NOT stare at the operating light source. It may be harmful to the eyes.

• Wear appropriate eye protection or turn on the supplement light only at a safe distance (0.3 m) or in an area that is not directly exposed to the light when installing or maintaining the device.

Please follow the steps below to call the menu. Note: The actual display may vary with your camera model.

Step 1. Connect the camera with the TVI DVR and the monitor.

Step 2. Power on the camera, TVI DVR, and monitor to view the image on the monitor.

Step 3. Click PTZ Control to enter the PTZ Control interface.

Step 4. Call the camera menu by clicking the appropriate button or calling preset No. 95.

Click the direction buttons to control the camera:

1. Click the up/down direction buttons to select menu options.

2. Click Iris + to confirm the selection.

3. Click the left/right direction buttons to adjust the value of the selected option.

The main menu of the HIKVISION DS-2CE76K0T-LMFS is organized into the following sections:

• VIDEO FORMAT

• EXPOSURE

• LIGHTING SETTINGS

• VIDEO SETTINGS

• AUDIO SETTINGS

• FACTORY DEFAULT

• EXIT

• SAVE & EXIT

The HIKVISION DS-2CE76K0T-LMFS supports various video formats depending on the camera model. The available formats are as follows:

You can set the EXPOSURE MODE on your HIKVISION DS-2CE76K0T-LMFS to GLOBAL, BLC, HLC, or DWDR.

• GLOBAL: This is the normal exposure mode which adjusts lighting distribution, variations, and non-standard processing.

• BLC (Backlight Compensation): BLC compensates light to the object in the front to make it clear, but this may cause over-exposure of the background where the light is strong.

• HLC (Highlight Compensation): HLC detects strong spots (over-exposure portions of the image) and reduces their brightness to improve the overall image.

• DWDR (Digital Wide Dynamic Range): DWDR gives the camera the ability to view dark areas of the image as well as extremely lighted portions, or areas of high contrast.

AGC (Auto Gain Control) on your HIKVISION DS-2CE76K0T-LMFS optimizes the clarity of the image in poor light conditions. The AGC level can be set to HIGH, MEDIUM, or LOW. Note that the noise will be amplified when setting the AGC level.

The HIKVISION DS-2CE76K0T-LMFS offers several lighting settings, with IR and WHITE LIGHT available as modes.

• IR LIGHT: You can turn the IR LIGHT on or off to meet the requirements of different circumstances.

• SMART IR: This function is used to adjust the light to its most suitable intensity and prevent the image from over-exposure.

• D→ N Threshold (Day to Night Threshold): This controls the sensitivity of switching from day mode to night mode. You can set the value from 1 to 9. A larger value means the camera is more sensitive.

• N→ D Threshold (Night to Day Threshold): This controls the sensitivity of switching from night mode to day mode. You can set the value from 1 to 9. A larger value means the camera is more sensitive.

• WHITE LIGHT: Under this sub-menu, you can set the mode to OFF or AUTO.

Under the WHITE LIGHT sub-menu, you can set the mode to OFF or AUTO.

• OFF: Set it to OFF to disable this function.

• AUTO: In this mode, you can configure THRESHOLD and LEVEL.

– THRESHOLD: The higher the threshold, the more sensitive the device is to a dark environment.

– LEVEL: You can adjust the maximum brightness of the supplement light.

Move the cursor to VIDEO SETTINGS and click Iris+ to enter the submenu. The following settings are adjustable:

• IMAGE MODE

• WHITE BALANCE

• BRIGHTNESS

• CONTRAST

• SHARPNESS

• SATURATION

• DNR

IMAGE MODE is used to adjust the image saturation on your HIKVISION DS-2CE76K0T-LMFS. You can set it to one of the following:

• STD (Standard)

• HIGH-SAT (High Saturation)

• HIGHLIGHT (better for indoor facial details)

White balance is the white rendition function of the HIKVISION DS-2CE76K0T-LMFS. It adjusts the color temperature according to the environment to remove unrealistic color casts in the image. You can set the WHITE BALANCE mode to AUTO or MANUAL.

In MANUAL mode, you can set the R-GAIN/B-GAIN value to adjust the shades of red/blue color in the image.

These settings on your HIKVISION DS-2CE76K0T-LMFS allow you to fine-tune the image quality:

• BRIGHTNESS: Refers to the brightness of the image. You can set the value from 1 to 9 to darken or brighten the image. The greater the value, the brighter the image.

• CONTRAST: This feature enhances the difference in color and light between parts of an image.

• SHARPNESS: Determines the amount of detail an imaging system can reproduce.

• SATURATION: This is the proportion of pure chromatic color in the total color sensation. Adjust this feature to change the saturation of the color.

• DNR: DNR refers to digital noise reduction. This function reduces noise in the video stream.

Under the AUDIO SETTINGS sub-menu on your HIKVISION DS-2CE76K0T-LMFS, you can set the mode to ON or OFF. You can also adjust the VOLUME to a higher value to raise the volume.

To reset your HIKVISION DS-2CE76K0T-LMFS, navigate to the FACTORY DEFAULT option in the menu. This will reset all settings except the video format to their factory defaults.

You have two options for exiting the menu on your HIKVISION DS-2CE76K0T-LMFS:

• EXIT: Move the cursor to EXIT and click Iris+ to exit the menu without saving any changes you made.

• SAVE & EXIT: Move the cursor to SAVE & EXIT and click Iris+ to save the settings and then exit the menu.