GARMIN VARIA VUE (01) PDF DOCUMENT

Please be aware of the following warnings when using your GARMIN VARIA VUE:

See the Important Safety and Product Information guide in the product box for product warnings and other important information.

The device can improve situational awareness. It is not a replacement for cyclist attentiveness and good judgement. Always maintain awareness of your surroundings, and operate the bicycle in a safe manner. Failure to do so could result in serious injury or death.

The device is intended for outdoor use. Without proper airflow during use, the device may become hot. Handle with care.

Always consult your physician before you begin or modify any exercise program.

Yes. Some jurisdictions regulate or prohibit the use of headlight camera devices. It is the responsibility of the user to know and follow all applicable laws in the jurisdiction where the device is intended to be used.

You can use the GARMIN VARIA VUE with your compatible Garmin device or a phone. This list provides an overview of the installation and setup tasks.

1. Charge the device.

2. Install and format the memory card.

3. Install the headlight on your bike.

4. Download the Garmin Varia app to your phone, and pair the devices.

5. If you are using an Edge series bike computer, pair the devices.

6. If you are using a Garmin watch, pair the devices.

You can use the out-front mount to install the headlight and your Edge bike computer. Garmin recommends that you adjust the mount for the viewing angle of the Edge bike computer before you install and adjust the headlight angle.

1. Select a secure location to mount the Edge bike computer and headlight where they do not interfere with the safe operation of your bike.

2. Use the 2.5 mm hex key to remove the screw from the handlebar connector.

3. Place a rubber pad around the handlebar:

• If the handlebar diameter is 25.4 mm, use the thicker pad.

• If the handlebar diameter is 31.8 mm, use the thinner pad.

• If the handlebar diameter is 35 mm, do not use a rubber pad.

4. Place the handlebar connector around the rubber pad. NOTE: You should align the contours on the rubber pad with the grooves on the inside of the handlebar connector.

5. Replace the screw, and use the 2.5 mm hex key to tighten the screw. NOTE: You should check the tightness of the screw periodically. Garmin recommends a torque specification of 7 lbf-in. (0.8 N-m).

6. Install the Edge bike computer, and adjust the mount (optional).

7. Connect the quarter-turn adapter to the headlight.

8. Insert the screw, and hand tighten.

9. Align the notches of the quarter-turn adapter with the tabs on the bottom of the mount.

10. Press up slightly, and turn the adapter counterclockwise until it locks into place.

11. Adjust the headlight angle so it is parallel to the ground, and use the 4 mm hex key to tighten the screw. NOTE: You should check the tightness of the screw periodically.

• Select a secure location to mount the device where it does not interfere with the safe operation of your bike.

• Select a mount that best fits your bike.

• Install the device correctly. The device faces forward, and must be mounted underneath the handlebars.

• Make sure there are no obstructions in front of the light.

• Adjust the headlight angle so it illuminates the ground ahead.

• To correctly line up the headlight, use the camera preview feature on the Varia app.

• If using an Edge bike computer, install the mount so the bike computer is visible from a comfortable riding position.

• Go for a test ride during the day in a safe environment.

1. Hold the device button for 1 second to turn on the device. The first time you turn on the headlight, it enters pairing mode. The status LED flashes purple. The device can be paired with the Varia app or an Edge bike computer.

2. Hold the device button for 2 seconds to turn off the device.

The GARMIN VARIA VUE is a safety device with a camera, providing peace of mind that the latest footage is always captured. When the camera is enabled, the device is always recording in a circular video loop, overwriting the oldest video footage with new footage.

You can save a video recording manually to prevent it from being overwritten during typical usage. If the memory card is full with saved video, the device will overwrite the oldest saved video to continue recording.

TIP: After you save a video recording, you should download the recording to your phone, or transfer the recording to your computer or other external storage location for permanent storage. You can purchase a Vault subscription to store your video in a secure online storage server.

TIP: Garmin recommends periodically backing up saved footage to your phone, computer, or the Garmin Vault.

When the camera is enabled, the device is always recording and saving video to the memory card, overwriting the oldest video footage with new footage. You can also save video files and photos manually at any time to prevent the camera from overwriting them.

• On the device, press the camera button.

• From the Varia app, select the photo or video icon.

• On your compatible Edge bike computer, select an option:

– To take a photo, select Take Photo.

– To save a 2-minute segment of video, select Save Clip.

– To manually save video, select Film Ride

TIP: To stop saving video, hold the camera button for 2 seconds.

The memory card has limited storage. After you manually save a video recording, you should download the recording to your phone, or transfer the recording to your computer or other external storage location for permanent storage. Saved recordings are automatically displayed in the Locked folder when your paired phone is connected to a Wi-Fi network.

By default, the device uses a sensor to detect possible incidents and saves video footage automatically before, during, and after the detected event. The video footage is stamped with the time, date, and location (if available) of the event.

The GARMIN VARIA VUE supports three different recording modes.

The GARMIN VARIA VUE stores video footage in a circular loop in 2-minute segments and in chronological order. The Varia app stitches consecutive 2-minute segments into 10-minute videos.

The length of manually saved video segments corresponds to the duration between starting and stopping the video, up to a maximum of 10 minutes. If the video is longer than 10 minutes, it will be broken into multiple videos.

Incident event videos are 90 seconds long if recording mode is continuous, with 15 seconds of footage preceding the occurrence of the incident. If recording mode is off, only 75 seconds of video footage is recorded starting from when the incident occurred.

Videos and photos are stored in the DCIM directory on the memory card. Videos are stored in MP4 and GLV file format, and photos are stored in JPG format. GLV is a low-resolution video file that provides a better mobile preview experience in the Varia app.

The videos and photos are sorted into folders:

The Varia app connects to your GARMIN VARIA VUE headlight using Bluetooth technology. The app displays light information, settings, videos, and photos.

• 1. Select to take a photo.

• 2. Displays the available light setting modes.

• 3. Indicates your current light setting mode.

• 4. Displays the battery status of the paired Varia device.

• 5. Select to change the device and camera settings.

• 6. Select to open the video and photo gallery.

• 7. Select to update the sounds and alerts on your phone. Select to view your Vault videos, settings, and more. NOTE: Vault features require a paid subscription.

• 8. Select to start saving a video.

• 9. Displays your current recording mode.

You can pair your GARMIN VARIA VUE to the Varia app on your phone to customize device settings, receive software updates, and view and edit video. After the initial pairing, the Varia app automatically connects to the Varia Vue when you open the app and the headlight device is active and within range.

1. Bring your phone within range (0.3 m) of the Varia Vue. NOTE: Stay 10 m away from other Bluetooth sensors while pairing.

2. On your compatible phone, enable Bluetooth technology.

3. From the app store on your phone, install and open the Varia app.

4. Select Add New Device.

5. While the Varia Vue is turned off, hold the device button for 2 seconds to enter pairing mode. The device status LED flashes purple, and the device turns on. The device is in pairing mode for 5 minutes or until you press the device button.

6. Select Pair.

7. Select an option:

• To store your videos with Vault, a secure online storage server, select Get Started, and follow the on-screen instructions. NOTE: Vault features require a paid subscription.

• To store your videos on the microSD card only, select Not Now.

When the Varia Vue is paired with your phone, the app displays the current light mode.

1. From the Varia app, select the menu icon.

2. Select Devices > Add Device.

3. Follow the on-screen instructions to complete the pairing and setup process.

When both the GARMIN VARIA VUE and a Varia radar device are paired with your phone, the app displays both devices.

Before you can view videos and photos on the Varia app, you must download the app and pair it with your GARMIN VARIA VUE device. NOTE: The device stops recording while you are viewing the gallery.

1. From the Varia app, select the gallery icon. The app opens to the Downloaded folder.

2. To view other folders, select an option:

• To view a saved video or photo, select Locked.

• To view recent, unsaved video footage, select Unlocked.

3. Select Join Varia Wi-Fi Network.

4. Follow the on-screen instructions.

Before you can download videos and photos on the Varia app, you must download the app, and pair it with your GARMIN VARIA VUE device. NOTE: The device stops recording while you are viewing the gallery.

1. From the Varia app, select the device icon at the top of the home screen.

2. Select Gallery & Storage > Gallery.

3. Follow the on-screen instructions.

4. Select the Locked or Unlocked folder.

5. Select a video or photo from the thumbnail gallery.

6. Select the menu icon, and select an option:

• To download the video or photo and delete it from its current folder, select Download & Delete.

• To download the video or photo and keep a copy in its current folder, select Download.

7. Select Downloaded to view the downloaded video or photo.

TIP: Select Add to Vault and following the on-screen instructions to upload your video or photo to your Garmin Vault account (optional).

Before you can delete a video or photo on the Varia app, you must download the app and pair it with your GARMIN VARIA VUE device. NOTE: The device stops recording while you are viewing the gallery.

1. From the Varia app on your phone, select gallery icon > Join Varia Wi-Fi Network, and follow the on-screen instructions.

2. Select the Locked or Unlocked folder.

3. Select a video or photo from the thumbnail gallery.

4. Select the menu icon on the video or photo.

5. Select Delete.

On the Varia app, select the device icon at the top of the home screen.

• Camera Configuration: Allows you to set up the camera, change recording mode, customize the video options, and enable incident recording.

• Gallery & Storage: Allows you to delete videos and photos in the gallery and format your memory card.

• Software Updates: Displays the software version and device information.

1. From the Varia app, select the device icon at the top of the home screen.

2. Select Camera Configuration > Recording Mode.

3. Select an option:

• Select Continuous to turn on camera recording when the device turns on.

• Select On Radar Activity to record video only when a compatible radar device radar that is connected to the app detects a vehicle. NOTE: If no radar device is connected, your camera will continuously record in this mode.

• Select Off to disable camera recording.

You can set the resolution of video recorded by the camera. Resolution is the width and height of the video in pixels. FPS is the number of video frames captured each second. Settings with a higher resolution or FPS require more memory card space.

You can turn on electronic image stabilization (EIS) to reduce shaky video.

1. From the Varia app, select the device icon at the top of the home screen.

2. Select Camera Configuration > Video Quality & Audio.

3. Select the Stabilize Video toggle switch.

The device records audio using the integrated microphone while recording video. You can turn off audio recording at any time.

1. From the Varia app, select the device icon at the top of the home screen.

2. Select Camera Configuration > Video Quality & Audio.

3. Select the Record Audio During Ride toggle switch.

1. From the Varia app, select the menu icon > Sounds & Alerts.

2. Select an option.

You can pair your GARMIN VARIA VUE with a compatible Edge bike computer through an open connection using ANT+ technology. After the initial pairing, the Edge bike computer automatically connects to the Varia device when you start your activity and the device is active and within range.

1. Bring the Edge bike computer within range (3 m) of the Varia Vue. NOTE: Stay 10 m away from other sensors that use ANT+ technology while pairing.

2. Turn on the Edge bike computer.

3. Select menu > Sensors > Add Sensor > Search All.

4. While the Varia Vue headlight is turned off, hold the device button for 2 seconds to enter pairing mode. The status LED flashes purple and the headlight turns on. The device is in pairing mode for 5 minutes or until you press the device button.

5. Select your sensor.

When the headlight device is paired with your Edge bike computer, the sensor status is Connected. The bike light status icon appears solid on the top banner of the home screen.

The status widget on your Edge bike computer displays the status of the GPS, sensors, and wireless connections.

Select an option:

• If your Edge bike computer uses a touchscreen, swipe down from the top of the home screen or a data screen.

• If your Edge bike computer uses device buttons, press up or down from the widgets screen.

The status widget appears. A flashing icon means the device is searching. A solid icon means the signal was found or the sensor is connected.

Before you can customize Varia device settings with your Edge bike computer, you must pair the devices.

1. From the Sensors menu, select Lights.

2. Select an option:

• Select Enable to enable the light network.

• Select Network Options > Light Mode to set the light intensity mode for all lights in your network.

• Select Network Options > Light Beam Activated to turn on the headlight automatically when the timer starts or when the Edge bike computer turns on.

• Select Network Options > Test Lights to check that each light in your network is set up correctly.

• Select Network Options > Auto Beam Adjustment to adjust the headlight intensity automatically based on the rate of speed. A high intensity is used at high speeds, and a low intensity is used at low speeds.

• Select a light to view device information and customize each light in your network.

From the Sensors menu, select Lights > Network Options > Light Mode.

• Auto: Automatically adjusts the light intensity and light mode based on the ambient light and time of day. This mode is recommended for commuting or road rides.

• High Visibility: Sets the light intensity to flash mode or the brightest setting available.

• Trail: Automatically adjusts the light intensity and light mode based on the ambient light and time of day. This mode is recommended for trail riding.

• Individual: Allows you to customize the light intensity and pattern mode for each light in your network.

1. From the Sensors menu, select Lights > Network Options > Test Lights.

2. Select a light to test.

The light blinks when it is connected.

When paired with a compatible Edge bike computer, the headlight can adjust automatically based on the current lighting conditions, sunrise and sunset information, and speed.

As your speed increases, the headlight shines brighter. At lower speeds, the light intensity is reduced to maximize battery life.

Before you can adjust the Varia light intensity with your Edge bike computer, you must pair the devices.

1. On your Edge bike computer, disable the automatic beam setting.

2. Go for a ride.

3. Select an option:

• If your bike computer uses a touchscreen, swipe the screen to view the bike lights widget.

• If your bike computer uses device buttons, press the menu icon, select Widgets, and press the up or down device buttons to view the bike lights widget.

4. Select High or Low to adjust the headlight beam.

Before you can control the Varia camera with your Edge bike computer, you must pair the devices.

1. Go for a ride.

2. Select an option:

• If your bike computer uses a touchscreen, tap the screen to view the timer overlay, and select the arrow icon. TIP: You can also control the camera using the quick action buttons on the timer overlay.

• If your bike computer uses device buttons, press the menu icon, and select Camera Controls. The bike computer displays the camera controls, as well as the recording mode, battery status, video resolution, and audio status of all connected cameras.

3. Select an option:

• Select Headlight Camera to customize the camera settings.

• Select the settings icon to customize the quick action buttons that appear on the timer overlay.

• Select Take Photo, Save Clip, or Film Ride.

Before you can customize Varia camera settings with your Edge bike computer, you must pair the devices.

1. Go for a ride.

2. Select an option:

• If your bike computer uses a touchscreen, tap the screen to view the timer overlay, and select the arrow icon.

• If your bike computer uses device buttons, press the menu icon, and select Camera Controls.

3. Select Headlight Camera.

4. Select an option:

• Select Video Recording to set the recording mode or turn off video recording.

• Select Resolution to set the video resolution recorded by the camera.

• Select Audio Recording to turn on or off audio recording.

• Select Image Stabilization to enable electronic image stabilization (EIS) and reduce shaky video.

You can pair your GARMIN VARIA VUE with a compatible Garmin watch, such as a Forerunner watch. When paired, the device controls appear on the compatible watch. You can also control the camera on the compatible device.

1. Bring the watch within range (3 m) of the Varia Vue. NOTE: Stay 10 m away from other sensors that use ANT+ technology while pairing.

2. Turn on the Garmin watch.

3. From the Settings menu, select Connectivity > Sensors & Accessories > Add New > Search All.

4. While the Varia Vue headlight is in active mode, hold the device button for 2 seconds to enter pairing mode. The status LED flashes purple. The device is in pairing mode for 5 minutes or until you press the device button to exit pairing mode.

5. Select your sensor.

When the headlight device is paired with your Garmin watch, the bike light status icon appears solid.

NOTE: Vault features require a paid subscription.

From the Varia app, you can connect your GARMIN VARIA VUE to a Wi-Fi network. When plugged into a wall charger and connected to a Wi-Fi network, your Varia Vue automatically uploads images and videos from the device’s memory card to your Vault account.

1. Connect your Varia Vue to the Varia app.

2. From the Varia app, select the device icon at the top of the home screen.

3. Select Vault Settings > Connect to Wi-Fi > Add a New Network.

4. Follow the on-screen instructions.

The next time you plug your Varia Vue into a wall charger within range of the saved Wi-Fi network, your device automatically reconnects to this network and uploads saved footage to your Vault account. The device LED flashes alternating blue and green to indicate the device is uploading videos to the Vault.

To prevent corrosion, thoroughly dry the USB port, the weather cap, and the surrounding area before charging or connecting to a computer. The device is powered by a built-in lithium-ion battery that you can charge using a standard wall outlet. NOTE: The device does not charge when outside the approved temperature range.

1. Pull up the weather cap from the USB port.

2. Plug the USB cable into the charging port on the device.

3. Plug the other end of the cable large end of the USB cable into an AC adapter or USB charging port.

4. Plug the AC adapter into a standard wall outlet.

5. Charge the device completely. The status LED flashes green while charging. The status LED is solid green when charging is complete.

6. Remove the USB cable, and close the weather cap.

• Connect the charger securely to the Varia device.

• You can charge the device by plugging the USB cable into a Garmin approved AC adapter with a standard wall outlet or a USB port on your computer. Garmin recommends charging the device using an AC power source.

• Remove the charger from the device when the status LED is solid green.

• View the remaining battery life on the Edge bike computer status widget or Varia app.

• Charge the device at least once a year to ensure it remains operable.

To prevent corrosion, thoroughly dry the USB port, the weather cap, and the surrounding area before charging or connecting to a computer. You can connect the device to your computer to install software updates or transfer videos and photos to your computer.

1. Pull up the weather cap from the USB port.

2. Plug one end of the cable into the USB port on the device.

3. Plug the other end of the cable into a computer USB port.

Depending on your computer operating system, the device appears as either a removable drive or a removable volume on your computer.

The device supports 8 to 512 GB microSD memory cards with a speed rating of Class 10 or higher. Garmin recommends using a 32 GB or higher microSD memory card. NOTE: You can replace a memory card to increase the storage capacity or when it has reached the end of its useful life. All memory cards have a limited life and must be replaced periodically.

1. On the back of the device, slide the tab to unlock the memory card cover.

2. Press the existing memory card in until it clicks, and release the card. The existing memory card ejects from the slot.

3. Remove the existing memory card from the slot.

4. With the gold contacts facing upward, insert the new memory card into the slot.

5. Press the memory card in until it clicks.

6. Close and latch the cover.

7. Go to the Varia app to format the memory card.

NOTICE: Formatting the memory card deletes all data on the card. Erased data cannot be restored.

You can reformat the memory card installed in your camera to erase all photos, videos, and other data. You may also need to format the memory card the first time you use it in your camera.

1. Turn on the headlight, and connect it to the Varia app.

2. Select the device icon at the top of the home screen.

3. Select Gallery & Storage > Erase & Reformat Card > Erase & Format.

• Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage.

• Avoid chemical cleaners, solvents, sunscreen, and insect repellents that can damage plastic components and finishes.

• Secure the weather cap tightly to prevent damage to the USB port.

• Avoid extreme shock and harsh treatment, because it can degrade the life of the product.

• Keep the memory card cover in the latched position to prevent water ingress.

• NOTE: Do not store the device in smart mode to prevent the battery from draining and to prevent accidently turning on the headlight.

NOTICE: Avoid chemical cleaners and solvents that can damage plastic components. Do not use a cloth or any material that can scratch the optical lens on the front of the device. Scratching the optical lens may cause poor performance.

• Clear mud and dirt from the weather cap area.

• While the weather cap is closed, hold the device under running water.

After cleaning, allow the device to dry completely.

1. Turn off the device and disconnect the device from power.

2. Clean the USB port using a soft, clean, lint-free cloth or cotton swab. NOTE: If necessary, you can lightly dampen the cloth or cotton swab with isopropyl alcohol.

3. Allow the device to dry completely before you connect it to power.

When you do not plan to use the GARMIN VARIA VUE device for several months, you should charge the battery to at least 50% before you store the device. You should store the device in a cool, dry place with temperatures around the typical household level. After storage, you should fully recharge the device before using it.

The actual battery life depends on the features enabled on your headlight, such as light intensity mode, video resolution setting, and electronic image stabilization (EIS).

You can reset the device if it stops responding. NOTE: Resetting the device deletes the pairing connections from the device, and clears all personal data stored on the device. It does not remove any data stored on the memory card. To protect your data on the memory card, you should format or remove the memory card from the device.

1. Turn the device on.

2. Hold both buttons for 10 seconds. The LED flashes red and green continuously, until the reset is complete.

If the device is turned off, you can lock the device, preventing it from turning on.

1. Hold both buttons for 4 seconds to lock the device. If you press any button, the status LED flashes yellow three times.

2. Hold both buttons for 4 seconds to unlock the device. The device turns on, and the status LED double flashes green. The device is in active mode, and the camera is on.

To prevent overheating, the GARMIN VARIA VUE may turn off when operated at a high intensity in warm, stagnant air. This is a thermal safety shutdown. The status LED flashes red until the device cools down. You should use the device outdoors.

If the status LED flashes red while charging, try the following:

• Check the USB cable, connectors, and ports for damage.

• Make sure the AC adapter or computer USB port is generating power. You can check this several ways. For example, you can check whether other devices powered by the source are functioning.

• Charge the device within the approved charging temperature range.

If the headlight is not connected, Garmin recommends that you stop riding and check the devices in a safe location.

• Turn off Bluetooth technology from your phone settings, and turn it back on.

• Close and reopen the Varia app.

• Turn off both devices, and turn them back on.

The Varia Vue sends light data to the Varia app. When connected, the Varia app plays an audio tone and displays a green dot at the device icon at the top of the home screen.

If the headlight is not connected, Garmin recommends that you stop riding and check the devices in a safe location.

• Turn both devices off, and turn them back on.

• Pair the devices again.

The Varia Vue sends light data to the Edge bike computer. The Edge bike computer displays the light network icon when connected.

There are three different ways to check the battery level.

• On the Varia Vue, press the device button to turn it on.

– Green light: The battery level is OK

– Red light: The battery level is low

• On your connected Edge bike computer or Garmin watch, open the sensors menu, and select the headlight camera.

• On the Varia app, select the device icon at the top of the home screen. The battery status is displayed at the top left of the screen. TIP: When the battery is low, the app displays a low battery notification at the top of the screen.

Before you can update the device software, you must pair the device with the Varia app on your phone.

1. Bring your phone within range (3 m) of the device.

2. Sync your device with the Varia app. When new software is available, the app alerts you to update the software. TIP: You can check for software updates in the app by selecting the device icon at the top of the home screen, and selecting Software Updates.

3. Follow the on-screen instructions.

The device LED flashes alternating yellow and green to indicate the device is updating. When the update is complete, the LED flashes green 20 times.

For the best experience, you should keep the software on your GARMIN VARIA VUE up to date. Software updates provide changes and improvements to the device features and operation. Your Varia device automatically checks for updates when connected using Bluetooth technology. On your computer, you can install Garmin Express. On your phone, you can install the Varia app.

This provides easy access to these services for Garmin devices:

• Software updates

• Data uploads to the Varia app

• Product registration

• Vault subscription setup

Before you can update your device software, you must download the Garmin Express application.

1. Connect the device to your computer using the USB cable. Garmin Express looks for software updates automatically and sends them to your device.

2. Follow the on-screen instructions.

3. Disconnect the device, and turn it on. The device LED flashes alternating yellow and green to indicate the device is updating. When the update is complete, the LED flashes green 20 times.