ELECTROLUX DBGL1032CN (01) PDF Document

The control panel of the ELECTROLUX DBGL1032CN has several functions indicated by different buttons and indicators:

You should check the recommended speed for your ELECTROLUX DBGL1032CN according to the table below:

To operate the ELECTROLUX DBGL1032CN cooker hood, follow these steps:

1. Press the first speed button to switch on the appliance.

2. If needed, press the light button to illuminate the cooking surface.

3. If needed, change the speed by pressing the desired button.

4. To turn off the appliance, press the first speed button again.

It is recommended to leave the hood operating for approximately 15 minutes after cooking.

The Hob²Hood function on your ELECTROLUX DBGL1032CN is an automatic feature that connects the hob with the hood. Both the hob and the hood have an infrared signal communicator. The speed of the fan is defined automatically based on the mode setting and the temperature of the hottest cookware on the hob. You can also operate the fan manually using the hob. The function can be activated from the panel of the hob.

The filter alarm on your ELECTROLUX DBGL1032CN reminds you to change or clean the charcoal filter and the grease filter.

• The filter indicator turns on for 30 seconds if the grease filter must be cleaned.

• The filter indicator flashes for 30 seconds if the charcoal filter must be replaced or cleaned.

To reset the function, press the filter notification button for 3 seconds.

To activate or deactivate the filter notification function on your ELECTROLUX DBGL1032CN, follow these steps:

To activate the function:

1. Press the filter notification button for 3 seconds. If the function is activated, the indicator will flash two times.

To deactivate the function:

1. Press the filter notification button for 3 seconds. If the function is deactivated, the indicator will flash once.

The ELECTROLUX DBGL1032CN can be controlled with a remote control. The connection is originally enabled. To connect or disconnect the remote control, follow these steps:

1. Switch off the appliance.

2. Press the maximum speed button for 3 seconds.

The indicator on the control panel will flash twice if the function is enabled and once if it is disabled.

For proper cleaning and maintenance of your ELECTROLUX DBGL1032CN:

• Do not use abrasive detergents and brushes. Clean the surface of the appliance with a soft cloth with warm water and a mild detergent.

• After cooking, some parts of the appliance can get hot. To avoid stains, the appliance must be cooled down and dried with a clean cloth or paper towels.

• Clean stains with a mild detergent.

• Clean the appliance and grease filters each month. Carefully clean the interior and grease filters to remove fat. Fat accumulation or other residue may cause a fire.

• Grease filters can be washed in a dishwasher. The dishwasher must be set to a low temperature and a short cycle. The grease filter may discolour, but this has no influence on the performance of the appliance.

• The activated charcoal filter is not washable and cannot be regenerated. It must be replaced approximately every 4 to 6 months of operation, or more frequently for particularly heavy usage.

The filters on the ELECTROLUX DBGL1032CN are mounted with clips and pins on the opposite side. To clean the filter:

1. Press the handle of the mounting clip on the filter panel underneath the hood.

2. Slightly tilt the front of the filter downwards, then pull.

3. Repeat the first two steps for all filters.

4. Clean the filters using a sponge with non-abrasive detergents or in a dishwasher. The dishwasher must be set to a low temperature and a short cycle. The grease filter may discolour, but this does not affect the appliance’s performance.

5. To mount the filters back, follow the first two steps in reverse order. Repeat the steps for all filters if applicable.

The charcoal filter is non-washable. To replace the charcoal filter on your ELECTROLUX DBGL1032CN:

1. Remove the grease filters from the appliance.

2. Press the front edge in the slot towards the bottom part of the filter. Slightly tilt the front of the filter downwards.

3. To install a new filter, perform the same steps in reverse order.

In any case, it is necessary to replace the filters at least every four months.

If you cannot activate your ELECTROLUX DBGL1032CN, check the following possible causes and remedies:

If the lamp on your ELECTROLUX DBGL1032CN is not working, it is likely defective. The appliance is supplied with an LED lamp and separate control gear (LED driver), and these parts can only be replaced by a technician. Please refer to the “Service” section in the “Safety Instructions” chapter of the user manual.

If your ELECTROLUX DBGL1032CN does not absorb enough vapours, the motor speed may not be adequate for the appearing vapours. You should change the speed of the motor to a higher setting.

If the filter alarm indicator on your ELECTROLUX DBGL1032CN is on, it means the filter alarm is active. The grease filter must be cleaned, or the charcoal filter must be replaced or cleaned. Refer to the filter notification in the “Daily use” chapter for instructions on how to proceed.