Click here to download ELATION PROFESSIONAL TVL3000CW (01) PDF MANUAL

PDF Content Summary:

****** Page 1 ****** TVL3000WW/TVL3000CW General Information ATOo PROFESSIONAL TVL3000WW/TVL3000CW ooe 000 ooe o@oo 0 0 0 Unpacking: Thank you for purchasing the TVL3000WW or TVL3000CW by Elation Professionalso. Every TVL3000WW & TVL3000CW has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without contacting customer sup- port first. Introduction: The TVL3000WW & TVL3000CW are DMX intelligent LED fixture’s. The TVL3000WW & TVL3000CW have 1 DMX channel, which is a master dimmer. This fixture’s have two operating modes; manual mode or DMX controlled. The TVL3000WW & TVL3000CW can only be run as stand alone unit. The light projections can be enhanced using fog or special effects smoke. Customer Support: Elation Professionals@ provides a toll free cus- tomer support line, to provide help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at for any com- ments or suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time. Voice: Fax: E-mail: (323) 582-3322 (323) 832-9142 o User Instructions 7/11 To purchase parts online visit Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture. Warning! This may cause severe eye damage. Avoid looking directly into the light source at all times! OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 2

****** Page 2 ****** TVL3000WW/TVL3000CW General Instructions TVL3000WW/TVL3000CW Safety Precautions To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference. TVL3000WW/TVL3000CW • 1 DMX Channel: Dimmer • 2 Operating Modes – Manual Mode & DMX Control • Digital Display for Address and Function Setting • TVL3000WW Warm White Temperature: 2700-3300K • TVL3000CW Cool White Temperature: 5000-6000K Features • 4 Beam Angles: 100/250/400/600 TVL3000WW/TVL3000CW Warranty Registration The TVL3000WW & TVL3000CW carry a 2 year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase and warranty. You may also register your product online at All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your proof of purchase invoice. Please contact Elation@ customer support for a R.A. number. TVL3000WW/TVL3000CW Handling Precautions Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures war- ranty. In the unlikely event your unit may require service please contact Elation Professionalso. During operation the housing may become hot. Avoid touching the unit with bare hands while in use. Elation Professionalse will not accept any liability for any resulting dam- ages caused by the non-observance of this manual or any unauthor- ized modification to this unit. For Your Own Personal Safety, Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit! • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit. Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. Disconnect from main power before making any type of connection. Do not remove the cover under any conditions. There are no user serviceable parts inside. Never operate this unit when it’s cover is removed. • Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6″ (15cm) between this device and a wall. Do not attempt to operate this unit, if it becomes damaged. • This unit is intended for indoor use only, use of this product out- doors voids all warranties. • Always mount this unit in safe and stable matter. Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep- tacles, and the point where they exit from the appliance. • Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 14 for cleaning details. • Heat -This fixture should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. • The fixture should be serviced by qualified service personnel when: A. Objects have fallen, or liquid has been spilled into the appliance. B. The appliance has been exposed to rain or water. C. The appliance does not appear to operate normally or exhibits a marked change in performance. OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 3 OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 4

****** Page 3 ****** TVL3000WW/TVL3000CW Set Up TVL3000WW/TVL3000CW Set Up Power Supply: The Elation Professionals@ TVL3000WW & TVL3000CW contain an automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere. Also be sure to only use the included I.E.C. power cable supplied with the unit. DMX-512: DMX is short for Digital Multiplex. This is a universal pro- tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fix- ture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal). DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a sin- gle controller, as long as all fixtures and the controller are DMX com- pliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): The TVL3000WW & TVL3000CW have 1 DMX channel. The DMX address is set electronically using the controls on the rear of Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground post on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX512 OUT 3-PIN XLR XLR Male Socket 1 Ground 3 Hot Figure 3 10 30 COMMON DMX + DMX – 01 03 02 DMX512 IN 3-PIN XLR Figure 2 XLR Female Socket 1 Ground 3 Hot XLR Pin Configuration Pin 1 = Ground Pin 2 = Data Compliment (negative) Pin 3 = Data True (positive) Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con- nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic the unit. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data cable for data input and data output. We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro- fessional sound and lighting stores). Your cables should be made with a male and female XLR con- nector on either end of the cable. Also remember behavior. OEIation Professionals@ 01 3 2 Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. Figure 4 Figure 1 that DMX cable must be daisy chained and cannot be split. OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 5 – – TVL3000WW/TVL3000CW Instruction Manual Page 6

****** Page 4 ****** Set Up 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting stan- dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion. 3-Pin XLR to 5-Pin XLR Conversion TVL3000WW/TVL3000CW Blackout Mode ” Yes Blackout ” TVL3000WW/TVL3000CW System Menu DMX512 Address Setting Conductor Ground/Shield Data Compliment (- signal) Data True (+ signal) Not Used Not Used OEIation Professionals@ 3-Pin XLR Female (Out) 5-Pin XLR Male (In) Pin I Pin 2 Pin 3 Pin I Pin 2 Pin 3 Pin 4 – Do Not Use Pin 5 – Do Not Use 1 MENU 1 u OEIation Professionals@ use n FF Dimmer Mode Blackout Mode ‘ Self-test LED on LED off Normal Inversion Fixture Hours No Blackout ” – – TVL3000WW/TVL3000CW Instruction Manual Page 7 Software Version – – TVL3000WW/TVL3000CW Instruction Manual Page 8

****** Page 5 ****** TVL3000WW/TVL3000CW System Menu TVL3000WW/TVL3000CW ‘Xin CILI IL-I — Blackout or Stand by mode. System Menu System Menu. The TVL3000WW & TVL3000CW come with an easy to navigate system menu. This next section will detail the functions of each command in the system menu. Please read the next section thoroughly! To access the main menu press the MENU button. Tap the UP or DOWN buttons until you reach the function you wish to change. When you reach the function you wish to change press the ENTER button. When a function is selected use the UP or DOWN buttons to change the function settings. Once your changes are made press the ENTER button, and then press and hold the MENU button for at least three seconds to confirm and lock the change into the system memory. If the MENU button is not pressed and held within eight seconds the fixture will automatically confirm and lock the change into the system memory. To exit without making any changes press the MENU button. rn—tna I¯IUUIX DMX Address Setting. 1. First set the unit to your desired DMX Channel mode. 2. To set your address, tap either the MENU, UP, or DOWN buttons until “RüüR” is displayed, press ENTER. “l” will now be displayed and flashing. 3. Press the UP or DOWN buttons to find your desired address. When you have found your desired DMX address press ENTER, and connect your DMX Controller. rumm Lili II | Dimmer mode. 1. Press the MENU button until ill is displayed, press ENTER. 2. Use the UP and DOWN buttons to adjust the intensity until you reach your desired intensity. OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 9 1. Press the MENU button until “BLNü” is displayed, press ENTER. Either Yes or No will be displayed. 2. To activate Blackout press the UP or DOWN buttons until Yes is displayed, press ENTER to confim and exit. The fixture will now be in Blackout mode. To deactivate Blackout mode, select No and press Enter. TESå – This function will run a self test program. 1. Tap the MENU button until “TEST” is displayed, press ENTER. 2. The fixture will now run a self test program. To stop the self test press either the MENU or ENTER button. I-Eu With this function you can have the LED display turn off after 20 seconds. 1. Press the MENU button until “LEO” is displayed, press ENTER. 2. The display will show either “ÜINI” or “OFF”. Press the UP or DOWN buttons to select I-III to keep the LED display On at all times, or “OFF” so that the LED display turns off after 20 sec- onds. 3. Press ENTER to confirm. WISP This function will reverse the display 1800. 1. Press the MENU button until “ü}SP” is displayed, press ENTER. 2. Press the UP button to select to reverse the display, or I-FF to reverse it back. 3. Press ENTER to confirm. OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 10

****** Page 6 ****** TVL3000WW/TVL3000CW System Menu TVL3000WW/TVL3000C Universal DMX Control FHRS – With this function the display will show the run- ning time (in hours) of the unit. Press the MENU button until “FHRS” is displayed, press ENTER. 2. The display shows the life time of the unit. Press MENU to exit. VER – Use this function to display the Software version of the unit. 1. Press the MENU button until “VER” is displayed, press ENTER. 2. The display will show the software version. Universal DMX Control: This function allows you to use a Elation@ universal DMX-512 controller to create unique programs tailored to your individual needs. 1. 2. 3. 4. 5. 6. 7. The TVL3000WW/TVL3000CW have one DMX channel, see page 13. To control your fixture in DMX mode, follow the set-up procedures on pages 5-7 as well as the set-up specifications that are included with your DMX controller. Use the controller’s faders to control the various DMX fixture traits. This will allow you to create your own programs. Follow the instructions on page 9 to set the DMX address. For longer cable runs (more than a 100 feet) use a terminator on the last fixture. For help operating in DMX mode consult the manual included with your DMX controller. TVL3000WW/TVL3000CW Changing the Beam Angle When changing the beam angle unscrew the thumb screw and remove the previous lens kit and replace with the new kit, now replace the thumb screw. The 100 lens is the lens that comes attached to the unit. 0 000 000 00 Manual Mode: This mode allows the user to adjust the dimming so that you can manually set your desired color temperature. 1. Press the MENU button until “Ü}IFIIIFII” is displayed, and press ENTER. 2. Use the UP and DOWN buttons to adjust the intensity until you reach your desired intensity. TVL3000WW/TVL3000CW Installation The unit should be mounted using a mounting clamp (not provided), affixing it to the mounting bracket that is provided with the unit. Always ensure that the unit is firmly fixed to avoid vibration and slip- ping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit’s weight. Also, always use a safety cable that can hold 12 times the weight of the unit when installing the fixture. The equipment must be installed by a professional, and it must be installed in a place where it is out of the reach of people’s grasp. OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 1 1 OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 12

****** Page 7 ****** TVL3000WW/TVL3000CW 1 Channel mode Dimmer DMX Mode Photometric Chart TVL3000WW/TVL3000CW Cleaning Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp output. 255 TVL3000WW/TVL3000CW 100% 1. 2. 3. 4. 5. Use normal glass cleaner and a soft cloth to wipe down the out- side casing. Use a brush to wipe down the cooling vents and fan grill. Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days. Always be sure to dry all parts completely before plugging the unit back in. TVL3000WW/TVL3000CW Trouble Shooting CWI 00 WW100 CW250 WW25@ CW400 wvv400 CW600 WW600 82691 60580 55617 42252 16587 13488 8994 6094 10 20673 15145 13094 10563 4147 3372 2248 1524 20 TVL3000 9188 6731 6180 4695 1843 1499 999 677 30 5168 3786 3476 2641 1037 843 562 381 4.0 3308 2423 2225 1690 664 540 360 244 (lux) 60 • .3m 3.6m 9.0m Trouble Shooting: Listed below are a few common problems that you may encounter, with solutions. 1. The unit does not work, no light and the fan does not work Check the power connection on both the unit and power source. 2. Not responding to DMX controller DMX LED should be on. If not, check DMX connectors and cables make sure they are linked properly. If the DMX LED is on and no response to the channel, check the address settings If you have intermittent DMX signal problems, check the pins on connectors. -u Try to using another DMX controller. Check if the DMX cables run near or run alongside high voltage cables that may cause damage or interference to DMX interface 50 OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 13 circuit. OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 14

****** Page 8 ****** TVL3000WW/TVL3000CW 2-YEAR LIMITED WARRANTY Warranty A. Elation@ Architectural hereby warrants, to the original purchaser, Elation@ Professionals@ products to be free of manufacturing defects in material and workmanship for a period of two years (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service, send the product only to the Elation@ Professionals@ factory. All shipping charges must be pre-paid. If the requested repairs or ser- vice (Including parts replacement) are within the terms of this warranty, Ela- tion@ Professionals@ will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, Elation@ Professionals@ shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which Elation@ Professionals@ concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation@ Professionals@ factory unless prior written authorization was issued to purchaser by Elation@ Profes- sionals@; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include mainte- nance, cleaning or periodic check-up. During the period specified above, Ela- tion@ Professionals@ will replace defective parts at its expense, and will absorb all expenses for warranty service and re air labor by reason of defects in mate- rial or workmanship. The sole responsi ility of Elation@ Professionals@ under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Elation@ Professionals@. All products covered by this warranty were manufactured after January 1, 1990, and bear identifying marks to that effect. E. Elation@ Professionals@ reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation@ Profession- als@ in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no war- ranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation@ Professionals@ be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. G. This warranty is the only written warranty applicable to Elation@ Profession- als@ Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. OEIation Professionals@ – – TVL3000WW/TVL3000CW Instruction Manual Page 15 TVL3000WW/TVL3000CW Model: Voltage: LEDs: Power Consumption: Dimensions: Without Bracket: With Bracket: Weight: Colors: DMX: Working Position: Warranty: Specifications TVL3000WW/TVL3000CW 110 240V-50/60Hz 24 x 3W LEDs 70W 222mm x 135.5mm x 194mm 222mm x 200mm x 317 mm 14.3 Lbs. / 6.5 kgs. TVL3000WW: Warm White TVL3000CW: Cool White 1 DMX Channel Any Safe, Secure Position 2 Year (730 days) Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. Auto Sensing Voltage: This fixture contains a automatic volt- age switch, which will auto sense the voltage when it is plugged into the power source. OEIation Professionals@ A Division of the AmericanDJ@ Group of Companies World Headquarters: 6122 S. Eastern Ave. Los Angeles, CA 90040 USA Tel: 323-582-3322 Fax: 323-832-9142 • E-mail: Web. American DJ Europe Junostraat 2 6468 EW Kerkrade Netherlands / Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99








Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.