Free English BELKIN AV360 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD BELKIN AV360 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
Who should install the BELKIN AV360 system?
The BELKIN AV360 should only be installed by a licensed cable electrician skilled in the field of low voltage indoor cable installs. The BELKIN AV360 solution is not intended for do-it-yourself installation as critical damage to building, hardware and bodily harm may occur if not properly installed.
What is the intended usage environment for the BELKIN AV360?
The purchase and usage of BELKIN AV360 is for indoor application only.
What are the supported cable lengths for BELKIN AV360 solutions?
Composite, S-Video, or Component: 25-100ft extension cables will work with composite, s-video or component wall plates. The composite, s-video or component adapters will only work with 25 and 50ft extension cables.
VGA or VGA+Stereo Audio: up to 300’ with wallplate terminations.
HDMI: up to 250’ with wallplate terminations.
Can BELKIN AV360 extension cables pass through conduits?
The BELKIN AV360 is designed to pass straight conduits and 90 degree bending conduits. However, the BELKIN AV360 will not pass through 90 degree tight angled conduits.
What matching requirements exist for the BELKIN AV360 cabling and wallplates?
The BELKIN AV360 Extension Cable Type MUST match the BELKIN AV360 Wallplates. The cables are color-coded to match the wallplates. Any non-color matched configuration will result in non-performance and potential damage to the cabling and active components.
What tools are required to install the BELKIN AV360?
Phillips screwdriver
Pull rod, fish tape and/or pull line
Optional, if junction box is not used:
Electric Drill
Drywall saw
Wall anchor screws
How do I distinguish between the TX and RX wallplates on the BELKIN AV360?
BELKIN AV360 powered wallplates have a designated TX sticker for transmitter and RX sticker for receiver on the individual wall plate:
TX is the source side: DVD, PC, or Media player
RX is the display side: Projector, monitor, or TV
What is the installation procedure for the BELKIN AV360 with an electrical junction box and conduit?
1. Install electrical conduit and [2-port] junction boxes at the TX and RX locations according to local electrical codes.
2. Pull BELKIN AV360 extension cable through the conduit using pull rod, fish tape or pull line attached to pull cap.
3. Remove pull caps and connect ends of BELKIN AV360 extension cable to the BELKIN AV360 wallplates.
4. Connect power adaptors to BELKIN AV360 wallplates. If the electrical outlet for the adaptor is behind the wall, route the cable through the wallplate cover’s notch.
5. Attach BELKIN AV360 wallplates to junction box.
What is the installation procedure for the BELKIN AV360 without an electrical junction box?
1. Using the enclosed template, cut the wallplate hole into the wall at both the TX and RX locations.
2. Drill the mounting holes according to the template and insert wall anchors screws.
3. Pull BELKIN AV360 extension cable from one wallplate hole to the other using pull rod, fish tape or pull line attached to pull cap.
4. Remove pull caps and connect ends of BELKIN AV360 extension cable to the BELKIN AV360 wallplates.
5. Connect power adaptors to BELKIN AV360 wallplates. If the electrical outlet for the adaptor is behind the wall, route the cable through the wallplate cover’s notch.
6. Attach BELKIN AV360 wallplates to the anchored holes on the wall.
How should the source and player be powered on when using the BELKIN AV360?
Once the extension cable is connected to the TX and RX wallplate, plug in the power adapter before turning on the source and player.
Do BELKIN AV360 HDMI wallplates upscale video resolution?
No, HDMI wallplates will not upscale video to 1080p if the source is not rated 1080p. Additionally, VGA wallplates will not upscale beyond source graphic card capability.
How do I adjust video settings on BELKIN AV360 VGA and HDMI wallplates?
For VGA wallplates: to make video adjustments, adjust the TX wallplate tuning button first, and then the RX wallplate tuning button to fine tune video image.
HDMI wallplates are plug & play, no additional adjustments needed.
What should I check if I am getting ghosting, shadowing, or fuzzy images on my monitor with the BELKIN AV360?
Check that all video cables are inserted properly.
Check that the monitor supports the resolution and refresh rate setting on your computer.
Check that the graphic card supports the resolution and refresh rate setting on your computer.
Hit auto adjust on monitor to see if the problem still appears.
VGA wallplates only: adjust the TX (transmitter) wallplate first, and then the RX (receiver) wallplate to fine tune the image to see if the problem still appears.
What should I check if I am getting ghosting, shadowing, or fuzzy images on my TV with the BELKIN AV360?
Check that all video cables are inserted properly.
Check that the TV supports the resolution and refresh rate setting on your DVD player.
Check that the DVD player supports the resolution and refresh rate setting on your TV.
Hit auto adjust on TV to see if the problem still appears.
VGA wallplates only: adjust the TX (transmitter) wallplate first, and then the RX (receiver) wallplate to fine tune the image to see if the problem still appears.
How do I troubleshoot a black screen when using the BELKIN AV360?
Check that all video cables are inserted properly.
If a power adapter is used, check that the power adapter is properly connected.
Connect the computer or DVD player directly to the monitor or TV to see if the problem persists.
Hit auto adjust on monitor to see if the problem still appears.
VGA wallplates only: adjust the TX (transmitter) wallplate first, and then the RX (receiver) wallplate to fine tune the image to see if the problem still appears.
CLICK HERE TO DOWNLOAD BELKIN AV360 (01) PDF DOCUMENT