ANKO 300155 (01) PDF DOCUMENT

To start the ANKO 300155 fabric shaver:

1. Rotate the handle counter-clockwise 180°.

2. Short press the switch button. The fabric shaver will turn on, and the default gear 1 will work. When there is no operation after 2 seconds, the LED will display the real-time power.

3. Short press the switch button again to switch to gear 2. When there is no operation after 2 seconds, the LED will display the real-time power.

4. Short press the switch button a third time to stop working.

Before using the ANKO 300155 fabric shaver:

• Read all instructions before use.

• Place the fabric on a flat surface such as an ironing board and pull it as straight as possible.

• Tuck in any loose threads before shaving and test the fabric’s suitability on an unexposed area first.

• Gently glide the shaving head over the fabric in an up and down motion.

• Do not press down heavily in order to prevent possible damage to the fabric.

• Use the rotation handle for comfortable use.

• Empty the fabric shaver after each use.

• Plug the small end of the supplied USB cable into the port located at the end of the handle. This appliance contains non-replaceable batteries.

• Ensure the charging adapter used is compatible with 5V 1A.

• The charging time is 3 hours. The LED digits will display the real-time battery percentage.

• The charging indicator will be flashed green while the fabric shaver is charging, and the charging indicator will stay on steady green when the fabric shaver is fully charged.

• The working time is approximately 1.5 hours from a full charge on gear 1, and approximately 1 hour from a full charge on gear 2.

• Note: Do not use the ANKO 300155 fabric shaver when it’s charging.

1. Remove the cap of the lint storage compartment to see the built-in lint compartment.

2. Sweep out the lint inside with the provided cleaning brush (part 8), then install the cap.

1. Pull the cotton thread outward to remove the washable lint remover.

2. After removing the washable lint roller, pull out the round fastener.

3. Rinse the lint roller with water and then reassemble it, then buckle up the round fastener.

• Use a damp cloth to wipe the surface of your fabric shaver. Do not allow water or other liquid to enter the inner parts of this device.

• To clean the shaving head or blades, switch off and unplug your fabric shaver. Unscrew the shaving head and use the cleaning brush provided to remove any bobbles or lint pieces, then screw the shaving head back on. Blades are sharp so please use caution.

• If the screen cover is loose or open when the power is on, the motor will shut down for safety.

When using the ANKO 300155, basic safety precautions should always be followed:

Electrical Safety:

• It must only be supplied at safety extra low voltage corresponding to the marking on the appliance.

• Before connecting the appliance, check if the voltage indicated on the bottom of the appliance is in accordance with the mains voltage in your home.

• To protect against electric shock, do not immerse the power cable, plug, or appliance in water or any other liquid.

• Any repairs must be conducted by a qualified electrician or electrical service agent.

Usage & Handling:

• WARNING: Keep the appliance dry.

• For domestic indoor use only. Do not use outdoors or for commercial use.

• Use this fabric shaver only as recommended in the manual.

• Use this fabric shaver on fabric only; it is not to be used on skin, hair or any other material.

• Do not use this fabric shaver on delicate, easily damaged fabrics. If unsure, test the fabric’s suitability on an unexposed area first.

• Before use, check thoroughly for any defects and do not use if defects are found. Take care not to drop the appliance as heavy impacts may cause internal damage.

• Check the appliance and power cable carefully for damage before each use.

• This fabric shaver is equipped with a sharp cutting blade; do not leave it unattended.

• Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children shall not play with the appliance.

Placement & Environment:

• Do not place on or near heat sources.

• Use on a level, stable surface.

• Do not cover the item in any way when in use as this may cause overheating.

• Ensure there is sufficient distance between this appliance and other items on the work surface or work station, or sufficient distance between the appliance and the confines of the area in which it is situated. We recommend a minimum clearance around all faces of at least 10cm.

Power & Accessories:

• Do not let the power cable hang over the edge of a table or counter, or touch hot surfaces. We recommend that the power cable is not kinked or stored in a twisted manner, and that you regularly check its condition.

• Unplug from outlet when not in use and before cleaning.

• Do not operate any appliance with a damaged power cable or plug or after the appliance malfunctions, or has been damaged in any manner.

• The use of any accessory attachments not recommended may cause injuries and invalidate any warranty you may have.

The parts of the ANKO 300155 are:

1. Cap

2. Stainless Steel Mesh Board

3. Fine mesh board

4. Blade

5. Rotation Handle

6. Washable Lint Remover

7. Type C Cable

8. Cleaning Brush

Dimensions

Height: 10.8cm

Width: 14cm

Length: 7cm

Power Details

5V-1A

Ta: 25°C

Protection Class: III

Rechargeable Battery

3.7V 1200mAh 18650 Li-battery