ALERATEC 240132 (01) PDF Document

The ALERATEC 240132 DVD/CD Disc Repair Plus offers the following features:

• Repairs minor scratches, scrapes, and abrasions

• Removes fingerprints, dust, and stains

• Forms a protective layer on the disc

• Hands-free operation during cleaning/repairing process

• Supports 12 cm and 8 cm discs

• User-friendly operation with automatic timer

The ALERATEC 240132 supports the following disc types:

• Standard sized (5 inch/12 cm) and Mini (3 inch/8 cm) discs

• DVD-Video Discs, DVD-ROMs, DVD±Rs, DVD±RWs

• Audio CDs, Karaoke CDs, CD-ROMs, CD-Rs, CD-RWs, and other optical discs

Please follow these precautions when using your ALERATEC 240132:

• Choose an appropriate location to install and operate the system.

• Allow adequate clearance for moving parts.

• Do not place near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibrations or shock.

• Disconnect the AC adapter from the outlet if the product is not used for an extended period of time.

• Proper care will help assure maximum product life.

Symptoms that may indicate minor damage include a scrambled screen, signal skipping, abnormal noise, unstable signal, or the inability to read a file.

For minor damage, perform the Disc Cleaning procedure first, then test the disc for improvements. If the disc is not sufficiently restored, follow with the Disc Repair procedure.

Symptoms indicating major damage include a frozen screen, no sound, no loading, or the system or drive is not accessible.

For major damage, first clean the disc with the Disc Cleaning procedure. Next, use the Disc Buffing procedure and finish with the Disc Repair procedure. Check for improvements to the disc’s condition. If not repaired, repeat the Disc Repair procedure until the disc is sufficiently restored.

The Disc Cleaning procedure removes surface contaminants such as dust, dirt, fingerprints, smudges, smears, and stains. Follow these steps:

1. Open the kit and remove the cleaning head marked “WET”.

2. Remove the cleaning head cover and then use the plastic end of the brush to remove the cleaning head and the spring.

3. Remove the cleaning solution from the kit. Then, fill the cleaning unit with solution until 80% full. Note: Upon initial use, a sharp object such as a safety pin must be used to puncture the mouth of the bottle.

4. Then replace the spring and the cleaning head.

5. Open the top cover and place the cleaning heads marked “WET” and “DRY” in their respective places, as indicated on the machine. Once in, rotate each of them in a counterclockwise direction until secure.

6. Insert the disc (data-side facing downward) and then close the top cover.

7. Press the CLEAN button to begin the cleaning process, which lasts approximately 20 seconds. The machine will automatically stop when the cleaning process has finished.

8. Once the disc is cleaned, press the OPEN button and remove the disc.

9. Re-attach the cleaning head cover.

Note: During continuous usage, the “Dry” cleaning head will gather moisture. If it becomes too damp, either replace it with another dry cleaning head or discontinue use until it is sufficiently dry.

The Disc Repair procedure is used to polish scratches, scrapes, and other abrasions. It also adds a protective layer to the disc. Follow these steps:

1. Open the top cover by pressing the OPEN button.

2. Remove both of the circular repair heads from the repair protective kit.

3. Rotate the repair units in a counterclockwise motion until secure.

4. Place 3 drops of the repair protective solution on the side of the repair head marked “WET”.

5. Insert the disc (data-side facing downward) and then close the top cover.

6. Press the REPAIR button to begin the repairing process, which lasts approximately two minutes. The machine will automatically stop when the process is complete.

7. Press OPEN to remove the disc.

8. Gently wipe the disc with the included microfiber cloth to remove any residue remaining from the repair process.

9. Check for improvements in the ability to play/read the disc. If the disc has not been sufficiently recovered, repeat the Disc Repair procedure.

The Disc Buffing procedure is intended for the most severely damaged discs. This process, which removes a small amount of plastic from the disc, allows deeper levels of damage to be repaired. Follow these steps:

1. Remove the pink Buffing units from the product packaging. Note: Buffing heads must be mounted onto clear plastic bases prior to use. Use the plastic end of the brush tool to pry each of the two Repair heads into its base. Install each Buffing head onto a base, pressing down gently until they snap into place.

2. Install the assembled Buffing heads into the motorized repair unit and rotate counter-clockwise to secure them.

3. Insert the disc (data-side facing downward) and close the top cover.

4. Press the REPAIR button to begin the Buffing process. It will run for approximately two minutes and stop automatically when complete.

5. Press the OPEN button to remove the disc, then follow with the Disc Repair Procedure to create a protective layer on your disc.

The motorized disc repair unit can be cleaned with a non-abrasive cloth dampened with isopropyl alcohol or ammonia-free glass cleaner. Do not use solvents.

When the Repair or Cleaning heads become dirty, clean them with the included brush and/or rinse with water, allowing sufficient drying time before use.

If the Buffing heads become soiled, use the included brush to remove any accumulated matter.

For best results, replace the various components according to the following schedule:

Cleaning Heads: 220 uses

Repair Heads: 20-25 uses

Buffing Heads: 10-20 uses

The following refills for the DVD/CD Disc Repair Plus are available: Aleratec DVD/CD Disc Repair Refill Value Pack, part no. 240138.