A-NEUVIDEO ANI-PIP-LITE (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download A-NEUVIDEO ANI-PIP-LITE (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** ANI-PiP-LlTEl HDMI 2×1 Multi-Viewer with PIP A»NEUVIDEO POWER OUT RS232 A-NeuVideo.com Frisco, Texas 75036 SOURCE HDMI INPUT MODE RESOLUTION HDMI OUTPUT OUT DC 5V IN A>NCUVIDEO

****** Page 2 ****** SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture. 5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth. 6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance. 7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced. 8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated. 9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection 10. 11 12 13. 14. 15. 16. 17. 18. 19. to improper AC voltage is not covered by any warranty. Tum power off and disconnect unit from AC current before making connections. Never hold a power switch in the “ON” position. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. The equipment power cord should be unplugged from the outlet when left unused for a long period of time. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. Service Information Equipment should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment. C. The equipment has been exposed to rain. D. The equipment does not appear to operate normally, or exhibits a marked change in performance. E. The equipment has been dropped, or the enclosure damaged. THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

****** Page 3 ****** A>NEUVIDEO SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. • Do not attach the power supply cabling to building suffaces. • Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. • Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. • To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use. We assume no responsibility for any inaccuracies that may be contained in this document We make no commitment to update or to keep current the information contained in this document. We reserve the right to make improvements to this document and/or product at any time and without notice COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means — electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent. @Copyright 2020. All Rights Reserved. Version 1.8 APR 2020 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. 1

****** Page 4 ****** TABLE OF CONTENTS INTRODUCTION & CONTENTS FEATURES & SPECIFICATIONS OPERATION CONTROLS & FUNCTIONS REMOTE CONTROL APPLICATION EXAMPLE MODE OPTIONS GUI SOFTWARE RS-232 PROTOCOL INTRODUCTION A>NEUVIDEO .2 ..3 .4 .6 .8 .9 11 The ANI-PiP-LlTE is a high performance (2) by (1) Multi-Viewer. It supports (2) High definition input source displays on (1) screen. As a Multi-Viewerj it can display on one screen in (4) different modes. This product has a 3 year warranty. PACKAGE CONTENTS Before attempting to use this unit} please check the packaging and make sure the following items are contained in the shipping carton: ANI-PiP-LlTE HDMI 2×1 Multi-Viewer • Remote Control • RS-232 Serial Cable • (2) Mounting Ears • 5V IA DC Power Adapter • Users Guide APPLICATIONS • Display an otherwise incompatible HDMI signal on an HDMI display • Upscale a standard definition video signal for display on a High Definition display • Lecture room/Showroom/Meeting room/Classroom signal display SYSTEM REQUIREMENTS HDMI source equipment such as a DVD player or set-top box and a HDMI equipped display and audio amplifier. 2

****** Page 5 ****** FEATURES / SPECIFICATIONS FEATURES HDMI 1.3a and HDCP 1.2 Compliant • Supports multiplexed HDMI (2) Inputs and (1) Output with (4) display modes Supports up to 1080p High Definition resolution • Supports scaler up and down functions • Supports multi output resolutions • Supports digital audio formats LPCM/AC3/DTS SPECIFICATIONS Video Bandwidth: 225MHz/6.75Gbps Input Ports: (2) HDMI (Female type) • Output Ports: (1) HDMI (Female type) Audio Output: PCM2, 5.1, 7.1 CH, Dolby 5.11 DTS5.1 •Input Resolutions: 480i60Hz, 480p60Hz, 576i50Hz, 576p50Hz, 720p50/601-lz, 1080i50/601-lzI 1080p24/30/50/60Hz, 800×600@60Hzl 1024×768@601-lzI 1280×720@60Hz, 1920×1080@60Hz • output Resolutions: 1080m 720p, 1080i, 1024×768, 1360×768 • ESD Protection: Human Body Model: •±8kV (air-gap discharge) • ±4kV (contact discharge) Dimensions (WxDxH): 2.6 x 5.5 x 1 in (70x140x25mm) Weight: .7 lb (300g) • Chassis Material: Metal • Operating Temperature: OOC-400C/ 320+1040F Storage Temperature: -200C 600C/-4ØF -1400F • Relative Humidity: 20-90% RH (non-condensing) • Power Consumption (Max): IOW Power Supply: 5V/lA DC (US/EU standards, CE/FCC/UL certified) As product improvements are continuous, specifications are subject to change without notice. 3

****** Page 6 ****** OPERATION CONTROLS & FUNCTIONS FRONT PANEL POWER OUT IN 1 SOURCE MODE POSITION S17E RESOLUTION O POWER LED: This red LED illuminates when the device is connected with the power supply. O OUTPUT LED: This red LED illuminates when the TV plug is in the corresponding HDMI output port. O INI LED: This red LED illuminates when the HDMI INI is selected as the main image. O IN2 LED: This red LED illuminates when the HDMI IN2 is selected as the main image. Receives the remote control signal. O SOURCE: Press the button to select the input source as the main image and the LED will indicate the corresponding input source. O MODE: Press the button to select the display mode. O POSITION: The position fuction is not avaialble via the front panel. To adjust the PiP position, use the GUI Software application. See page 8 of this users manual for more information. O SIZE: The size fuction is not avaialble via the front panel. To adjust the PiP size, use the GUI Software application. See page 8 of this users manual for more information. O RESOLUTION: Press the button to select the output resolution. 1 2 3 4 5 RESOLUTION 1080p, Main image audio 720p, Main image audio 1080i, Main image audio 1024×768, Main image audio 1360×768, Main image audio 4

****** Page 7 ****** OPERATION CONTROLS & FUNCTIONS BACK PANEL RS232 HDMI INPUT HDMI OUTPUT o DC 5V IN O RS-232: Connected to computer via RS-232 tool and controlled via host-computer software. O HDMI IN2: This slot is where you connect the HDMI source output from DVD, PS3} etc. O HDMI INI : This slot is where you connect the HDMI source output from DVD, PS3} etc. O HDMI OUTPUT: This slots is where you connect the HDTV or monitor with a HDMI cable. O DC 5V IN: Plug the 5V DC power supply into the unit. 5

****** Page 8 ****** REMOTE CONTROL O POWER: Press this button to power on the matrix or set it to standby mode. O INI: Press this button to select Input 1 as the main image. O IN2: Press this button to select Input 2 as the main image. O SIZE: Press the button to select the size of the sub image when in PiP mode. (Currently Not Supported.) O POSITION: Press these buttons to select the position of the sub image when in PiP mode. (Currently Not Supported.) O MODE: Press the button to select the display mode. O RESO: Press the button to select the output resolution. IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) CUSTOM CODE: 86E7 DATA CODES: 2 MOOE 17 1B 59 1 3 5 RESO. POWER: INI: IN2: SIZE: MODE: RESO 86E7 86E7 86E7 86E7 86E7 86E7 04 00 43 42 16 POSITION: DOWN. LEFT: RIGHT: 6 86E7 86E7 86E7 86E7

****** Page 9 ****** REMOTE CONTROL IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) CUSTOM CODE: 86E7 DATA CODES: POWER: INI: SIZE: MODE: RESO 86E7 86E7 86E7 86E7 86E7 86E7 04 00 43 42 16 POSITION: DOWN: LEFT: RIGHT: 7 86E7 86E7 86E7 86E7 17 1B 59 17 42 59

****** Page 10 ****** APPLICATION EXAMPLE USB DVD or Blu-ray Player DVD or Blu-ray Player nsocuoo• HDMI TV Power Supply HDMI

****** Page 11 ****** MODE OPTIONS O MODE 1: ONE-VIEW MODE O MODE 3: POP MODE A O MODE 4: POP MODE B Using this software allows the PiP image to be custom sized and placed anywhere on the screen. Once these settings are set} they will be retained in NVROM which means during a loss of power} the settings will remain.

****** Page 12 ****** GUI SOFTWARE Windows GUI Software available for download. Works on WIN XR WIN7 and WIN10. COM Port COMB OUTPUT Resdution mooE PIP MOOE Start pant X: Width: PIP MODE Start paint X: Width: O Cisconnect Restcre The Factory Settings AUDIO CIAudio independent switch check Reset logop 74 1746 74 1746 80ROER Upgra± Open BIN File goo Set C] Show Border Start point Y: y-Elght: goo Set Start point Y: Height: Start Point X: Is the starting position of the horizontal axis. “0” will be the top left corner. Width: (W) is the width of the image. Max value is dependent on the Output resolution. Start Point Y: Is the starting position of the vertical axis. “0” will be the top left corner. Height: (H) is the height of the image. Example 1: If the Output resolution is 1920x1080p. Example 2: If the Output resolution is 1920x1080p. x Width 1920 Height 1080 x Width 960 960 Height 540 540 That means, X+W=1920. The resulting image will be full screen. (Not practical) That means, X+W=1920. The resulting image will be PiP in the lower right corner. 10

****** Page 13 ****** AS-232 SERIAL INTERFACE ras-æsæ SERIAL INTERFACE FOR CONNECTION TO A PC on 3RD PARTY CONTROLLER 1. Transmission rate: 115200bps 2. Data format: 8 data bits, No parity, 1 start bit and 1 stop bit 3. Flowing control: None Also know as 115200,8jn,1 ras-232 CONFIGURATION RS-232 cable is a straight thru cable and not null-modem Definition Pin Pin Definition TX Device GND Data String Format 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 DCD TX DTR GND DSR RTS CTS RI The data string must conclude with an explanation point “!” (without the quotes). All text is full ASCII Code and is NOT case sensitive. 00000 0000 11

****** Page 14 ****** AS-232 COMMANDS COMMAND IN2! ONE-INPUT! PIP! SIDE-BYSIDEI! SIDE-BYSlDE2! ?VERSION! RESET! POWERON! POWEROFF! AMO! AMII IA2! ACTION Change resolution to 1080p Change resolution to 720p Change resolution to 1080i Change resolution to 1360×768 Change resolution to 1024×768 Select input 1 Select input 2 Select mode QUAD Select mode PIP Select mode POPI Select mode POP2 Check software version Factory Reset System power on System power off Audio switch follow Video Audio independent switch Select audio Input 1 Select audio Input 2 Change PiP Location and Height Example: 12 AM-QUAD-MINI RETURNS Resolution: Resolution: Resolution: Resolution: Resolution: 1080p/60 720p/60 1080i/60 1024×768/60 1360×768/60 Input 1 select Input 2 select Mode: QUAD Mode: PIP Mode: POPI Mode: POP2 V 1.7 Factory Reset PowerON PowerOFF Audio switch follows Video Audio independent switch Audio select 1 Audio select 2 xo yo wi00 h200 See GUI Intetface for more info

****** Page 15 ****** THIS PAGE IS INTENTIONALLY LEFT BLANK.

****** Page 16 ****** TERMS AND CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTSAND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NauVideo, INC (COLLECTIVELY THE “PRODUCT”). ay using installing or using the Product, you unconditionally signfy your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not usa the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Products packing label at your expense. A-NeuVldeo, Inc. may modify these Terms and Conditions at anytime, without notice to you. RESTRICTIONS ON USE OF THE PRODUCT It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you mh respect to the Product. You are authorized to usa the Product solely in connection wm such instructions. Any use of tha Product not in accordance with such instructions shall void any warranty pertaining to the Product Any and all damages that may occur in the use of the Product that is not strictly in accordanæ with such instructions shall be bome by you and you agree to indemnfy’ and hold harmless A-NeuVldeo, Inc. from and against any such damage. The Product is protected by certain intellectual propeny rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVideo, Inc. and/or its affiliatesr including any manufacturers or distributors of tha Product (collectively, “A-NeuVideo*) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product. The Product is sold to you end any use of any associated intellectual propeny is deemed to be Iiænsed to you by A-NeuVIdeo for your personal usa only. A-NeuVldeo does not transfer either the title or the intellectual propaty rights to the Product and A-NeuVideo retains full and complete title to tha intellectual propeny rights therein. All trademarks and ogos are omed by A-NeuVIdeo or its licensors and providers of the Product, and you mey not wpy or use them in any manner without tha prior written consent of A-NeuVideo, which c:onsent may be withheld at the sole discretion of A-NeuVldao. The functionalty’ and usability of the Product is controlled by A-NeuVideo, Inc. from its offices mhin the State of Texas, United States of America. A-NauVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that tha Product may be subject to U.S. export controls. DISCLAIMERS AND LIMITATION OF LIABILITY A-NauVideo mey change or modify the Product at any time: from time to time. THE PRODUCT IS PROVIDED “AS AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIOEO DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. A-NauVideo has no duty or polW/ to update any information or statements pertaining to the Product and, therefore, such information or staternents should not be relied upon as being current as of the date you use the Product Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may ba made from time to time without notic:e respect to the Product. TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCTWILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. Pa•dEClVlDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIOEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO CINDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIOEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OE OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF A-NEUVIOEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEOS TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO A-NEUVIDEQ IF ANY, FOR THE PRODUCT. END OF DOCUMENT


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.